Download Print this page
Teknik Hudson 5425815 Instructions Manual

Teknik Hudson 5425815 Instructions Manual

Wall mounted night stand

Advertisement

Quick Links

Hudson Wall Mounted Night Stand
Model 5425815
Teknik
www.teknikoffice.co.uk
For things and such.
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.

Advertisement

loading

Summary of Contents for Teknik Hudson 5425815

  • Page 1 Teknik www.teknikoffice.co.uk For things and such. Hudson Wall Mounted Night Stand NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Model 5425815 PLEASE READ AND KEEP FOR FUTURE REFERENCE.
  • Page 2 Table of Contents Assembly Tools Required Part Identifi cation No. 2 Phillips Screwdriver Tip Shown Actual Size Hardware Identifi cation Assembly Steps 5-17 Hammer Not actual size Français 18-19 Español 20-21 Pencil Safety Electric drill with 3/32" and 7/16" bit Warranty (ONLY in indicated step) Tape Measure...
  • Page 3: Part Identification

    Now you know Part Identifi cation our ABCs. å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identifi cation to help identify similar parts. LEFT END (1) BOTTOM (1) MOLDING (1)
  • Page 4: Hardware Identification

    Hardware Identifi cation å Screws are shown actual size. You may receive extra hardware with your unit. HIDDEN CAM - 12 CAM SCREW - 12 WOOD DOWEL - 24 BLACK APPLIQUE WHITE APPLIQUE WALL ANCHOR - 1 NAIL - 12 CARD - 1 CARD - 1 2-7/16"...
  • Page 5 Hardware Usage Guide HOW TO USE A HIDDEN CAM & CAM SCREW OR CAM DOWEL NOTE: Various CAM SCREWS or a CAM DOWEL may be used. Turn the CAM SCREW or gently tap the CAM DOWEL until the shoulder is against the surface of the part.
  • Page 6 Step 1 Assemble your unit on a carpeted fl oor or on the empty å carton to avoid scratching your unit or the fl oor. Remember: Righty tighty. Turn twelve CAM SCREWS (2) into the ENDS (A and B), å Lefty loosey.
  • Page 7 Step 2 Push twelve HIDDEN CAMS (1) into the ENDS (A and B) å and SHELF (F). Arrow Arrow (12 used) Arrow Page 7...
  • Page 8 Step 3 Insert two WOOD DOWELS (3) into the MOLDING (G). å Fasten the MOLDING (G) to the SHELF (F). Tighten two å HIDDEN CAMS. NOTE: Be sure the WOOD DOWELS in the MOLDING å insert into the SHELF. i t h f a c S u r D E N...
  • Page 9: Hidden Cam

    Step 4 Insert two WOOD DOWELS (3) into the RIGHT END (B). å Fasten the SHELF (F) to the RIGHT END (B). Tighten the å HIDDEN CAM. NOTE: Be sure the WOOD DOWELS in the RIGHT END å insert into the SHELF. This notch must be here.
  • Page 10 Step 5 Insert four WOOD DOWELS (3) into the RIGHT END (B). å Push the SMALL BACK (E) onto the WOOD DOWELS in å the RIGHT END (B). These holes will be smaller than the holes on the opposite surface. (4 used) Page 10...
  • Page 11 Step 6 Insert six WOOD DOWELS (3) into the SMALL BACK (E) å and SHELF (F). Now might be a good time to refresh Fasten the LEFT END (A) to the SMALL BACK (E) and å your drink. SHELF (F). Tighten the HIDDEN CAM in the SHELF. NOTE: Be sure the WOOD DOWELS in the SMALL BACK å...
  • Page 12 Step 7 Insert four WOOD DOWELS (3) into the BOTTOM (D). å Fasten the ENDS (A and B) to the BOTTOM (D). å Tighten four HIDDEN CAMS. NOTE: Be sure the WOOD DOWELS in the BOTTOM å insert into the ENDS. (4 used) Angled edge Page 12...
  • Page 13 Step 8 Insert six WOOD DOWELS (3) into the ENDS (A and B) å and BACK (E). Fasten the TOP (C) to the ENDS (A and B) and BACK (E). å Tighten four HIDDEN CAMS. NOTE: Be sure the WOOD DOWELS in the ENDS and å...
  • Page 14 Step 9 Turn your unit onto its front edges. å Place the LARGE BACK (H) into the groove of the å ENDS (A and B) and fasten it to your unit using the NAILS (7). NAIL (12 used for the BACK) Page 14...
  • Page 15 Step 10 You must fasten your unit to one wall stud and one å WALL ANCHOR (6). 1. You will need to locate a stud in your wall to fasten your unit. å Determine the desired height of unit on your wall and move 1-5/8"...
  • Page 16 Step 11 On the marks, drill a 3/32" hole in the center of a wall stud å and a 7/16" hole in your wall for the WALL ANCHOR (6). Next, push the wings of the WALL ANCHOR (6) together, å while inserting the WALL ANCHOR into the 7/16"...
  • Page 17 Step 12 With the help of another person, fasten your unit to the wall. Use two 2-7/16" FLAT HEAD SCREWS (8) into the wall å stud and into the WALL ANCHOR. Peel BLACK APPLIQUES from the BLACK APPLIQUE CARD (4) and stick them onto each visible HIDDEN CAM. å...
  • Page 18 WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Properly mounting the cabinet to the wall. •...