Advertisement
Quick Links
Advertisement
Related Manuals for Teknik 5425015
Summary of Contents for Teknik 5425015
- Page 1 Teknik The original desktop. Summit Desk Model 5425015...
- Page 2 Table of Contents Assembly Tools Required Part Identifi cation No. 2 Phillips Screwdriver Tip Shown Actual Size Hardware Identifi cation Assembly Steps 6-28 Hammer Not actual size Français 29-32 Español 33-36 Safety 37-38 Warranty Page 2...
- Page 3 Now you know Part Identifi cation our ABCs. å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identifi cation to help identify similar parts. RIGHT END (1) D540 PENCIL DRAWER BACK (1) FRONT/BACK MOLDING (2)
- Page 4 Hardware Identifi cation å Screws are shown actual size. You may receive extra hardware with your unit. 35GA CABINET RIGHT - 1 35GB CABINET LEFT - 1 35GC DRAWER RIGHT - 1 35GD DRAWER LEFT - 1 (EXTENSION SET SHOWN SEPARATED) EXTENSION RAIL - 2 EXTENSION SLIDE - 2 10A SLIDE CAM - 2...
- Page 5 Hardware Identifi cation å Screws are shown actual size. You may receive extra hardware with your unit. BLACK 9/16" LARGE HEAD SCREW - 4 3S GOLD 5/16" FLAT HEAD SCREW - 16 30S BLACK 1-9/16" FLAT HEAD SCREW - 8 BLACK 7/8"...
- Page 6 Step 1 Assemble your unit on a carpeted fl oor or on the empty carton to å avoid scratching your unit or the fl oor. Push twenty HIDDEN CAMS (1F) into the ENDS (A and B), å MODESTY PANEL (C), UPRIGHT (D), BOTTOM (E), BACK (M), and BRACE (N).
- Page 7 Step 2 Push eighteen HIDDEN CAMS (1F) into the remaining å holes of the ENDS (A and B), UPRIGHT (D), LEFT BRACE (G), and BOTTOM MOLDINGS (H and S). Arrow (18 used) Arrow Arrow Hole The arrow in the HIDDEN CAM must point toward the hole in the edge of the board.
- Page 8 Step 3 Turn eighteen CAM SCREWS (8F) into the LEGS (L, P, Q, and R). å First, fi ll the hole in the end of the LEG (Q) 1/4 to 1/2 full with å GLUE (177M). Then, insert the WOOD DOWEL (15F) into the hole. Wipe away the excess GLUE.
- Page 9 Step 4 First, fi ll the holes in the LEGS (Q and R) 1/4 to 1/2 full with å GLUE (177M). Then, insert the WOOD DOWELS (15F) into the holes. Wipe away the excess GLUE. Now, fi ll the holes in the LEFT END (B) and LEFT BRACE (G) å...
- Page 10 Step 5 Fasten the LEGS (L and P) to the RIGHT END (A) å and RIGHT BOTTOM MOLDING (S). Tighten six HIDDEN CAMS. NOTE: Position the RIGHT BOTTOM MOLDING (S) å exactly as shown. Edge with CAM DOWELS S u r f a c w i t h H I D...
- Page 11 Step 6 Fasten the LEGS (L and P) to the UPRIGHT (D) and LEFT å BOTTOM MOLDING (H). Tighten six HIDDEN CAMS. NOTE: Position the LEFT BOTTOM MOLDING (H) exactly å as shown. Edge with CAM DOWELS f a c S u r w i t h D E N...
- Page 12 Step 7 Separate the EXTENSION SLIDES (35MC) from the EXTENSION RAILS (35MA) as å shown in the upper diagram below. Be prepared, the parts are greasy. Fasten the EXTENSION RAILS (35MA) to the RIGHT END (A) and UPRIGHT (D). Use å...
- Page 13 Step 8 Carefully fl ip the UPRIGHT (D) over. å Fasten two EXTENSION BRACKETS (43G) to the UPRIGHT (D). Use four å BLACK 9/16" LARGE HEAD SCREWS (1S). Fasten the CABINET RIGHT (35GA) to the EXTENSION BRACKETS (43G) å on the UPRIGHT (D). Use two GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3.
- Page 14 Step 9 Fasten the MODESTY PANEL (C) to the å LEFT END (B). Tighten two HIDDEN CAMS. S u r f a c w i t h H I D D E N Roller end Caution Start Tighten Risk of damage or Arrow injury.
- Page 15 Step 10 First, fi ll the hole in the TOP (T) 1/4 to 1/2 full with GLUE (177M). å Maximum Arrow Then, fasten the LEFT END (B) and MODESTY PANEL (C) to å 210 degrees the TOP (T). Tighten four HIDDEN CAMS. NOTE: Be sure the WOOD DOWEL in the LEG (Q) inserts into å...
- Page 16 Step 11 Push two CROSS-SLOTTED DOWELS (24F) into the LONG BRACE (K) å as shown. 177M NOTE: The threads in the DOWEL should be pointed toward the hole in å the edge of the LONG BRACE. First, fi ll the holes in the ends of the LONG BRACE (K) 1/4 to 1/2 full å...
- Page 17 Step 12 First, fi ll the hole in the LEFT BOTTOM MOLDING (H) 1/4 to 1/2 å full with GLUE. Maximum Arrow 210 degrees Next, fasten the UPRIGHT (D) to the TOP (T). Tighten two å HIDDEN CAMS. Minimum NOTE: Be sure the WOOD DOWEL in the LONG BRACE (K) å...
- Page 18 Step 13 First, fi ll the holes in the BRACE (N) 1/4 to 1/2 full with å GLUE (177M). Then, insert the WOOD DOWELS (15F) Maximum Arrow into the holes. Wipe away the excess GLUE. 210 degrees Now, fi ll the hole in the UPRIGHT (D) 1/4 to 1/2 full å...
- Page 19 Step 14 Slide the FRONT/BACK MOLDINGS* (J) onto the å notched edges of the BOTTOM (E). Maximum Arrow 210 degrees Fasten the BOTTOM (E) to the LEFT BOTTOM å MOLDING (H). Tighten two HIDDEN CAMS. Minimum *U.S. Patent No. 5,499,886 å...
- Page 20 Step 15 First, fi ll the hole in the RIGHT END (A) 1/4 to 1/2 full å with GLUE. Maximum Arrow 210 degrees Next, fasten the RIGHT END (A) to the BOTTOM (E), å BACK (M), BRACE (N), and TOP (T). Tighten seven Minimum HIDDEN CAMS.
- Page 21 Step 16 Fasten the PENCIL DRAWER BACK (D540) to the PENCIL DRAWER SIDES (D266 and D267). Use å two BLACK 1-9/16" FLAT HEAD SCREWS (30S). Slide the PENCIL DRAWER BOTTOM (B51) into the grooves in the PENCIL DRAWER SIDES (D266 å...
- Page 22 Step 17 Fasten the DRAWER RIGHT (35GC) to the PENCIL RIGHT å DRAWER SIDE (D266) and the DRAWER LEFT (35GD) to the PENCIL LEFT DRAWER SIDE (D267). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. Roller end D267 Roller end...
- Page 23 Step 18 The tabs should insert freely With the palm of into the slots. Gently tilt the your hand, tap DRAWER SIDES side to side the DRAWER until the tabs slip into the slots. BOTTOM down into the groove. U n fi n i s h s u r f a c...
- Page 24 Step 19 Insert a SLIDE CAM (10A) into the FILE DRAWER SIDES (D14 and D15). å Fasten the EXTENSION SLIDES (35MC) to the FILE DRAWER SIDES (D14 and D15). Use four GOLD 5/16" å FLAT HEAD SCREWS (3S) through holes #1 and #3. NOTE: The screw head in the CAM must be visible through the slotted hole in the SLIDE.
- Page 25 Step 20 Push the FILE GLIDES (4B) onto the FILE DRAWER SIDES (D14 and D15). å Carefully stand your unit upright. å To insert the PENCIL DRAWER (O) into your unit, tip the front of the å drawer down and drop the rollers on the drawer behind the rollers on the unit.
- Page 26 Step 21 Insert the GROMMET (10P) and GROMMET CAP (1P) into å the large hole in the TOP (T). Page 26...
- Page 27 Step 22 Using your hammer, gently tap a CAM COVER (75P) onto å each visible HIDDEN CAM. 25 lbs. (6 used) To cover HIDDEN CAMS Page 27...
- Page 28 Step 23 To make adjustments to the drawer, loosen SCREW #3 in the SLIDES a 1/4 turn, then turn the cam clockwise or å counter-clockwise. Notice how the drawer raises or lowers as you turn the cam. By adjusting the drawer this way, it will help the DRAWER FRONT line up better when closed.
- Page 29 WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves or drawers. •...