Page 3
Rights Reserved. All other products mentioned herein may be trademarks of their respective companies. Information is subject to change without notice and does not represent a commitment on the part of Visioneer. The software described is furnished under a licensing agreement. The software may be used or copied only in accordance with the terms of such an agreement.
Page 4
FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for the class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed, and used in accordance with the instructions, may cause harmful interference to radio communications.
Page 6
Xerox DP1011 User’s Guide Welcome Your new Xerox DP1011 projector is an XGA single chip 0.7” DLP™ (Digital Light Processing) projector with these outstanding features: • True XGA, 1024 x 768 addressable pixels • 2.1 lbs (0.95 kgs) compact design •...
Page 7
If this happens, the projector will not turn back on until the lamp module has been replaced. To replace the lamp, follow the procedures in “Changing the Lamp” on page 21. Xerox DP1011 User’s Guide...
Do’s and Don’ts Xerox DP1011 User’s Guide • Turn off the projector before cleaning. • Use a soft cloth moistened with mild detergent to clean the display housing. • Disconnect the power plug from AC outlet if the projector is not being used for a long period of time.
What’s in the Box Xerox DP1011 User’s Guide Before proceeding, check the contents of the box. If items are missing or damaged, contact the dealer where you purchased the projector. Projector with lens cap Carrying Case Quick Start Card Tech Support Card...
The Xerox DP1011 Projector Elevator Button Zoom Lens Remote Control Receiver Xerox DP1011 User’s Guide Focus Ring Zoom Ring Power Connector Focus Ring—Rotate to focus the image. Zoom Ring—Rotate to zoom the image in or out. Elevator Button—Press to release the elevator foot to lower or raise the projector.
Input Connector VGA connector—for computer (PC Analog signal), HDTV, or Component Video Power Connector Xerox DP1011 User’s Guide S-Video Input Connector Remote Control Receiver Power Connector—Plug the power cord into the projector here. VGA Connector—Use the VGA cable that you received with your projector to plug in a computer, HDTV, or component video source.
5. Turn on the projector first, and then the computer. NOTE: Your DP1011 projector works best at computer screen resolutions of 1024 x 768 or less. To reset the computer screen resolution, see “Setting the Screen Resolution” on page 28.
Powering On/Off the Projector Xerox DP1011 User’s Guide To turn on the projector power 1. Remove the lens cap. 2. Make sure that the power cord and the cables from the video sources are securely connected to the projector. 3. Turn on the lamp by pressing the Power button on the control panel or on the Remote Control.
Warning Indicator Lights Xerox DP1011 User’s Guide To turn off the projector power 1. Press the Power button on the projector or Remote Control to turn off the projector lamp. An on-screen message appears: Power off the lamp? 2. Press the Power button again to confirm.
Adjusting the Projected Image Xerox DP1011 User’s Guide NOTE: The projector is equipped with an “elevator foot” for adjusting the projector height. To raise the projector 1. Lift the projector up and press the elevator button. The elevator foot pops out.
Distance 3.94’ (1.2m) 9.84’ (3.0m) Xerox DP1011 User’s Guide You adjust the focus and zoom in/out with the focus ring and zoom ring on the lens housing. To focus the image, rotate the focus ring until the image is clear. The projector can focus at distances from 3.94 feet to 32.81 feet (1.2m to 10.0m).
Panel Control and Remote Control Panel Control Xerox DP1011 User’s Guide User Controls The buttons on the Panel Control and the Remote Control are for controlling the projector’s functions. Power/Standby Warning Indicator Indicator Directional Select Keys Power/Standby Indicator—Flashes remains steady green when projector is ready.
Directional Selection Keys ( )—Selects items on the OSD menus. If an item is selected, makes adjustments to that selected item Menu—Opens the On-screen Display (OSD) menus. Press the Menu button again to exit the OSD. Xerox DP1011 User’s Guide...
On-Screen Display (OSD) Menus Displaying Menus and Selecting Items Xerox DP1011 User’s Guide The On-Screen Display (OSD) menus provide the options to make image adjustments and change a variety of settings. The projector automatically detects the video source so your selections from the menus will apply to that source.
Choose a Language Xerox DP1011 User’s Guide 1. Press the Menu button on the Remote Control or Panel Control to open the OSD. 2. Select the Language menu and press the Enter button. The Language menu appears. 3. Use the keys to select the language you want.
Adjust the Projector Image Xerox DP1011 User’s Guide 1. Press the Menu button on the Remote Control or Panel Control to open the OSD. 2. Select the All Images menu and press the Enter button. The All Images menu appears.
Adjust the Computer Image Xerox DP1011 User’s Guide 1. Press the Menu button on the Remote Control or Panel Control to open the OSD. 2. Select the Computer Image menu and press the Enter button. The Computer Image menu appears.
Adjust the Video Image Xerox DP1011 User’s Guide 1. Press the Menu button on the Remote Control or Panel Control to open the OSD. 2. Select the Video Image menu and press the Enter button. The Video Image menu appears.
Projector Management Xerox DP1011 User’s Guide 1. Press the Menu button on the Remote Control or Panel Control to open the OSD. 2. Select the Management menu and press the Enter button. The Management menu appears. 3. Use the keys to select the item you want, and use the keys to adjust the selected setting.
Adjust the PiP (Picture in Picture) Xerox DP1011 User’s Guide 1. Press the Menu button on the Remote Control or Panel Control to open the OSD. 2. Select the PiP menu and press the Enter button. The PiP menu appears.
Changing the Lamp Xerox DP1011 User’s Guide Maintenance The projector’s lamp life is approximately 1500 hours of use. The projector automatically monitors the lamp life. After 1500 hours of use, the projector displays the message: The Lamp has been in use for over 1500 hours. You should purchase a spare bulb.
Page 27
4. Remove the cover. 5. Remove the two screws from the lamp module. 6. Lift up the handle and pull out the lamp module. Lamp Module 7. To replace the lamp module, reverse the previous steps. Xerox DP1011 User’s Guide...
Troubleshooting Xerox DP1011 User’s Guide If you try the troubleshooting procedures described in this section and the problem persists, you may have a malfunctioning projector. Refer to the technical support card that you received with your projector or contact the retailer where you purchased your projector.
Page 29
Xerox DP1011 User’s Guide For Windows 95, 98, 2000, XP: 1. From the Windows Start menu, select Settings/Control Panel and then double-click the Display icon. 2. Select the Setting tab. The Desktop Area shows the resolution setting. 3. Verify that the resolution setting is 1024 x 768 or less.
Page 30
Xerox DP1011 User’s Guide Problem: The image is flickering or otherwise unstable Try one of these possible solutions: • On the On-screen display, go to the Computer Mode page and select Tracking. Change the tracking until the image stabilizes. •...
Page 31
When the lamp reaches its end of life, it will burn out and may make a loud popping sound. If this happens, the projector will not turn on until the lamp module has been replaced. See “Changing the Lamp” on page 21 to replace the lamp. Xerox DP1011 User’s Guide...
Xerox DP1011 Projector Specifications Lamp Valve Lamp Number of Pixels Displayable Colors Projection Lens Projection Screen Size Projection Distance Video Compatibility Horizontal Frequency Vertical Frequency Power Supply Input/Output Connectors Weight Dimensions (W x H x D) Operating Environment Storage Environment Safety and agency certifications Xerox DP1011 User’s Guide...
If you have a Windows PC: If you have an Apple Macintosh: Xerox DP1011 User’s Guide For best viewing on your computer screen, its resolution should be set to 1024 x 768 or less. To reset the screen resolution, follow the steps below, referring to the chart on page 29 for the correct settings for your type of computer and monitor.
Page 34
Xerox DP1011 User’s Guide Compatibility Modes—Windows Computers Mode Resolution VESA VGA 640 x 350 VESA VGA 640 x 350 VESA VGA 640 x 400 VESA VGA 640 x 480 VESA VGA 640 x 480 VESA VGA 640 x 480 VESA VGA...
Page 35
Xerox DP1011 User’s Guide Compatibility Modes—Macintosh Computers Mode Resolution MAC 16”* 832 x 624 MAC 19”* 1024 x 768 MAC* 1152 x 670 MAC G4 640 x 480 MAC G4 640 x 480 MAC G4 1024 x 768 IMAC DV...