Subscribe to Our Youtube Channel
Related Manuals for allen WB1224
Summary of Contents for allen WB1224
- Page 1 WB1224 - WORK BRIDGE SAFETY / ASSEMBLY & PARTS MANUAL Manual Part #: 068521 | Revision: - Language: English | Original Instructions...
- Page 2 Allen Engineering Corporation (AEC). AEC assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual.
-
Page 3: General Information Limited Warranty
If Allen chooses to replace the part, it will be at no cost to the customer and will be made available to the Allen Distributor, Dealer, or Rental Center from whom the End User purchased the product. -
Page 4: Table Of Contents
Table of Contents GENERAL INFORMATION Sect Title Page General Information Limited Warranty ......................3 Load Capacity Ratings....................5 Information Contained in This Manual .................6 Dealer Information / Ordering Parts ................7 Model Number - Serial Number Codes ................8 Technical Specifications ....................9 Safety ........................10 Federal / State Warning Regulations .................11 Manual Tag Safety Detail ..................12 Spark Arrestor Notice / Hazard Symbols ..............13... -
Page 5: Load Capacity Ratings
Deflection should exceed no more than 2.62” with Maximum span/weight applied. Calculations are done without factoring weather. Please note that in adverse weather conditions, capacity ratings need to be decreased. Please contact Allen Engineering PRODUCT SUPPORT with any questions reguarding load capacity. 068521... -
Page 6: Information Contained In This Manual
Your engine and clutch is not manufactured by Allen Engineering Corporation, Inc, and there- fore is not covered under Allen Engineering Corporation, Inc warranty. -
Page 7: Dealer Information / Ordering Parts
Ordering Parts Your Dealer has Allen Engineering Corporation trained mechanics and original Allen replace- ment parts. Always contact the Allen Dealer who sold you this machine for Allen Certified repairs and replacement parts. Place Allen Dealer information below for future reference. -
Page 8: Model Number - Serial Number Codes
Model Number GENERAL INFORMATION Manufacturer’s Codes: When ordering parts or requesting service information, you will always be asked to specify the model and serial numbers of the machine. The legends below spe- cifically defines each significant character or group of characters of the Model Number and Serial Number codes. -
Page 9: Technical Specifications
These work bridges are ideal for joint work, applying curing compounds, bull-floating, applying textures or whenever a suitable platform for doing bridge work is required. The Allen Work Bridge is an economical workhorse on any job site. Work Bridge 1224 Dimensions (H x W x L) 12”... -
Page 10: Safety
SECTION 1 SAFETY SECTION 1 SAFETY Page 10 068521... -
Page 11: Federal / State Warning Regulations
Federal / State Warnings SECTION 1 SAFETY RESPIRATORY HAZARDS Grinding/cutting/drilling of masonry, concrete, metal and other materials can generate dust, mists and fumes containing chemicals known to cause serious or fatal injury or illness, such as respiratory disease, cancer, birth defects or other reproductive harm. -
Page 12: Manual Tag Safety Detail
Manual Tag Safety Detail SECTION 1 SAFETY Safety-Alert Signs This manual contains Safety-Alert Signs, as defined below, which must be followed to reduce the possibility of improper servi ce damage to the equipment or personal injury. Read and follow all Safety-Alert Signs included in this manual. -
Page 13: Spark Arrestor Notice / Hazard Symbols
Spark Arrestor Notice / SECTION 1 SAFETY Hazard Symbols Some states require that in certain locations arrestors be used on internal combustion engines. A spark arrester is a device designed to prevent the discharge of spark or flames from the engine exhaust. It is often required when operating equipment on for- ested land to prevent the risk of fires. -
Page 14: Operating Safety
Operating Safety SECTION 1 SAFETY Familiarity and proper training are required for the safe operation of this equipment! Equipment operated improperly or by untrained personnel can be dangerous! Read the operating instructions contained in both this manual and the engine manual and familiarize yourself with the location and proper use of all controls. -
Page 15: Engine Safety
Engine Safety SECTION 1 SAFETY Internal combustion engines present special hazards during operation and fueling. Read and follow the warning instructions in the engine owner’s manual and the safe- ty guidelines below. Failure to follow the warnings and safety guidelines could result in severe injury or death. -
Page 16: Service Safety
Service Safety SECTION 1 SAFETY Poorly maintained equipment can become a safety hazard! In order for the equipment to operate safely and properly over a long period of time, periodic maintenance and occasional repairs are necessary. • ALWAYS disconnect the battery before servicing the equipment. •... -
Page 17: Lifting Safety
Lifting Safety SECTION 1 SAFETY ALWAYS DO A THOROUGH INSPECTION OF THE SLINGS, CHAINS, AND HOOKS BEFORE ATTEMPTING TO LIFT THE MACHINE! OSHA has set forth guidelines which detail the use of Rigging Equipment for Material handling. This guideline is found under OSHA Standard Number: 1926.251 Please read and follow all guidelines found in this standard. - Page 18 Lifting Safety SECTION 1 SAFETY PLEASE CONSULT ON-SITE SAFETY COORDINATOR BEFORE ATTEMPTING TO LIFT MACHINE. IMPROPER RIGGING AND LIFTING CAN RESULT IN INJURY OR DEATH. BELOW IS AN EXAMPLE OF STRAP PLACEMENT AND LIFTING PROCEDURES, BUT THIS SHOULD NOT BE USED AS A GUIDE FOR LIFTING THE MACHINE! (ON LONGER WORKBRIDGES, A SPREADER BEAM MAY BE REQUIRED.) TO CRANE USE A 5,000 lb SHACKLE AS...
-
Page 19: Transportation Safety
Transportation Safety SECTION 1 SAFETY • Make sure the hitch and coupling of the towing vehicle are rated equal to, or greater than the trailer “gross vehicle weight rating.” • ALWAYS inspect the hitch and coupling for wear. Never tow a trailer with defective hitches, couplings, chains, etc. -
Page 20: Assembly
SECTION 2 ASSEMBLY SECTION 2 ASSEMBLY Page 20 068521... -
Page 21: Assembly Instructions
Assembly Instructions SECTION 2 ASSEMBLY See below for assembly of the WB1224 workbridge. Work Bridge Section Connections: Bolt Washer Spacer Rod End Cevis Pin Hairpin Connecting Clevis 1. Align WB section so that the Connecting Clevis sits outside the rod end. - Page 22 Assembly Instructions SECTION 2 ASSEMBLY Adjustable End Frame & Pneumatic Tire Assembly Adjustable WB Section End Frame Paving Style Wheel Slides Pneumatic Tire and Fork 1. Loosen clips on Adjustable End Frame (AEF) and place WB Section “on top” of AEF. 2.
- Page 23 Assembly Instructions SECTION 2 ASSEMBLY Bridge Deck End Brackets & Wheel Assembly Bridge Deck End Brackets WB Section Bridge Deck Style Wheel 1. Loosen clip and slide Bridge Deck End Bracket (BDEB) around workbridge section, and tighten clips back to secure end frame bracket. 2.
-
Page 24: Parts
SECTION 3 PARTS SECTION 3 PARTS Page 24 068521... -
Page 25: Mainframe Sizes
Mainframe Sizes SECTION 3 PARTS ITEM PART # DESCRIPTION 047568 Assembly, Mainframe, 2 Foot 047569 Assembly, Mainframe, 5 Foot 047570 Assembly, Mainframe, 7-1/2 Foot 068521 Page 25... -
Page 26: Mainframe Assembly - 2 Foot
Fastener, Nut, Hex, 1/2”-13 010125 Fastener, Pin, Clevis, 1/2” 010711 Clip, Hitch Pin, 1/8” x 2-9/16” 047469 Spacer, Workbridge, 27-1/4” 047552 Weldment, Frame, 2’ 056340 Decal, Allen Globe, 4” x 6.67” 010093 Fastener, Washer, Lock, 1/2”, Grade 8 Page 26 068521... -
Page 27: Mainframe Assembly - 5 Foot
Fastener, Nut, Hex, 1/2”-13 010125 Fastener, Pin, Clevis, 1/2” 010711 Clip, Hitch Pin, 1/8” x 2-9/16” 047469 Spacer, Workbridge, 27-1/4” 047551 Weldment, Frame, 5’ 056340 Decal, Allen Globe, 4” x 6.67” 010093 Fastener, Washer, Lock, 1/2”, Grade 8 068521 Page 27... -
Page 28: Mainframe Assembly - 7.5 Foot
Fastener, Nut, Hex, 1/2”-13 010125 Fastener, Pin, Clevis, 1/2” 010711 Clip, Hitch Pin, 1/8” x 2-9/16” 047469 Spacer, Workbridge, 27-1/4” 047550 Weldment, Frame, 7-1/2’ 056340 Decal, Allen Globe, 4” x 6.67” 010093 Fastener, Washer, Lock, 1/2”, Grade 8 Page 28 068521... -
Page 29: Endframe Assembly Kit
Endframe Assembly Kit SECTION 3 PARTS ITEM PART # DESCRIPTION 070061 Kit, WB1224, End Frame Assembly 020462 Assembly, End Frame Bracket (SET) 221029 Assembly, Tire, Pneumatic, with Attaching Fork 221115 Fork, Steering 221257 Slide, Wheel, Paving Style 068521 Page 29... -
Page 30: Endframe Bracket Assembly
Endframe Bracket Assembly SECTION 3 PARTS ITEM ITEM PART # DESCRIPTION 020462 Assembly, Endframe, Adjustable (SET) 010002 Fastener, Bolt, HHCS, 1/4”-20 x 3/4”, Grade 8 010106 Fastener, Nut, Hex, 1/2”-13 010125 Fastener, Pin, Clevis, 1/2” 010711 Clip, Hitch Pin, 1/8” x 2-9/16” 047469 Spacer, Workbridge, 27-1/4”... -
Page 31: Rubber Tire Assembly
Rubber Tire Assembly SECTION 3 PARTS ITEM PART # DESCRIPTION 221029 Assembly, Tire, Pneumatic 221029-F Assembly, Tire, Foam Filled 010087 Fastener, Washer, Flat, 3/4” 010088 Fastener, Washer, Flat, 1” 010133 Pin, Cotter, Ø3/16” x 2” 011195 Axle 221058 Assembly, Pneumatic Tire and Wheel, 16” 221058-F Assembly, Foam Filled Tire and Wheel, 16”... -
Page 32: End Frame Bracket - Bridge Deck Style
End Frame Bracket - SECTION 3 PARTS Bridge Deck Style ITEM PART N 010045 010050 010069 010071 010075 010076 010091 010093 010102 010106 050703 050704 050705 050707 050709 050714 051989 052995 ITEM PART # DESCRIPTION 048328 Assembly, End Frame, Bridge Deck Style 010045 Fastener, Bolt, HHCS, 3/8”-16 x 3-1/4”, Grade 8 010050... -
Page 33: Cup Wheel Tire Assembly
Cup Wheel Assembly SECTION 3 PARTS ITEM PART # DESCRIPTION 221124 Assembly, Wheel, Cupped, 6” 010088 Fastener, Washer, Flat, 1” 010133 Pin, Cotter, Ø3/16” x 2” 010157 Axle 052001 Assembly, Steel Cup Wheel, 6” 221128 Assembly, Fork 068521 Page 33... -
Page 34: Double Flange Wheel Assemlby
Double Flange Wheel Assembly SECTION 3 PARTS ITEM PART # DESCRIPTION 020463 Assembly, Wheel, Double Flange, 6” 010133 Pin, Cotter, Ø3/16” x 2” 010157 Axle 023888 Assembly, Double Flanged, 6” 221128 Assembly, Fork Page 34 068521... -
Page 35: Bridge Deck Style Wheel Options
Bridge Deck Style Wheel Options GENERAL INFORMATION Part #: 065015 Part #: 052744 Part #: 052745 Poly Coated, Double Flanged Steel, Double Flanged Steel, Double Flanged Drive Wheel for 2" Forms Idle Wheel for 2" Forms Drive Wheel for 2" Forms Part #: 065025 Part #: 042561 Part #: 042562... -
Page 36: Cleaning Procedure
Cleaning Procedure Machine Cleaning Procedure When cleaning the machine, please adhere to the following information to ensure proper cleaning and to keep the machine in the best condition possible. Power Washing Procedure: • Ensure that the water pressure is below 2000 PSI (14 MPa) •... -
Page 37: Revision Detail
Revision Detail MANUAL REVISION DETAIL REVISION REVISION REVISION REVISION REFERENCE # DATE 08/20 Initial Release 068521 Page 37... - Page 40 P.O. BOX 819 PARAGOULD, AR 72451 USA 800.643.0095 (USA ONLY) / 870.236.7751 FAX: 800.643.0097 (USA ONLY) / 870.236.3934 CONNECT WITH US ON...
Need help?
Do you have a question about the WB1224 and is the answer not in the manual?
Questions and answers