Table of content 1.Open-Package guidelines............... 1.1Package....................1 2.Safety instructions..................1 3.Operating determinations...............3 4.Rigging the fixture...................4 4.1 Mounting.....................4 4.2Installing the Clamps................4 4.3 Power supply connection and cut off...........5 4.4 Power Connection................6 4.5 DMX-512 connection/connection between fixtures......6 Description of the device............
Page 4
Congratulations on choosing our products! Please carefully read this instruction manual in its entirety and keep it well for using reference. This manual contained about the installation and the relative using information of this products. Plese refere this manual's relative instruction when using this equipment.
1.Open-Package guidelines This equipment is made of new style,high intensity plastic.It fully shows the modem times light charac teris- tic with teristic with beauty struture. And it is made accord to CE standard. Fully agree with the internation standard of DMX 512 agreement.
Page 6
Never let the power-cord come into contact with other cables! Handle the power cord and all connections with particular caution! Make sure that the available voltage is not higher than stated on the rearpanel. Always plug in the power plug least. Make suer that the power-switch is set to off-position before you con ections with themains with particular caution! Make sure that the power-cord is never crimped or damaged by sharp edges.Check the decice and the p- ower-cord from time to time.
lines of the projectors from indirect contact and/orshorting to earth by using appropriately sized residual current devices. Disposing This product is supplied in compliance with European Directive 2012/19/EU-Waste Electrical and Electronic Equipment (WEEE). To preserve the environment please dispose/recycde this product at the end of its life according to the local regulation.
4.Rigging the fixture 4.1 Mounting Pay attention to the regulations of CE. Installation by qualified staff to complete. For the various mounting positions of the FIXTURE(standing on the floor, sideways or hanging different accessories kits are available. Through this a safe and firm installation is assured. You’ll find special connectors on the bottom side of the system which are put to use here.
The projector can be placed directly on the stage floor or rigged in any orientation on atruss without alte- ring its operation characteristics. For overhead use,always install a safety-rope that can hold at least 10 times the weight of the fixture.You must only use safety-ropes with screw on carabines.Pull the safety-rope through the two apertures on the bottom of the base and over the trussing system etc.
4.4 Power Connection If you wish to change the power supply settings, see the chapter appendix Connect the fixture to the mains with the enclosed power cable and plug. Warning: please verify the power of the power supply equipment prior to the connection! Earth wire must be grounded! CABLE(EU) CABLE(US)
5.Description of the device Head °, Tilt Fixture could auto reset. °, Fixture could auto reset. Base 18.WDMX wire BACK PANEL 4.3-pin XLR female 5.5-pin XLR female 6.Power-in 10 9 7. Power switch 8.Main Fuse 9.5-pin XLR male 10.3-pin XLR male 11.Network interface Note:One of the above two power boards can be chosen at will!
7.Display control 7.1 Navigation in the Menu Using the buttons or touch screen, and this can be simply and easily set the address code and functions code. If you view or modify the lighting feature set, then press ENTER button, the display will enter the menu interface.
Page 14
Click on the main interface of the icon, numerical to view view Settings related information of lamps and lanterns.Symbols such as the main interface appear “ “,the following error message indicates that there might be a lamps and lanterns,can click to view and control information content to modify the lamps and lanterns.
7.3 Menu Maps Remark Dmx Address 001-XXX Mode1 1-39 Channel Mode default Mode1 Mode2 1-34 Fixture Id 0001-9999 2.X.X.X Default IP Address 10.X.X.X Enable Custom IP Address Ether net X.X.X.X (Optional) Net Mask 255.255.255.X Art-Net Universe 0-255 Network params Fixture Times XXXXX h XX m Lamp On Times XXXXh XXm Lamp Times...
8.DMX protocol Mode 1 Mode 2 Fade Type Function Dmx Value 0-255 Pan Fime Pan Fime 0-255 (16BIT) Tilt Tilt 0-255 Tilt Fime Tilt Fime 0-255 (16BIT) Standard mode Pan/Tilt speed , Max. Speed Mode Pan/Tilt time Time from 0.2 s to 25.5 sec 2 - 255 Reserved 0 - 19...
Page 17
Mode 1 Mode 2 Fade Type Function Dmx Value Yellow Linear Yellow movement 0-255 Continual positioning Open/white Deep Red Deep Blue Yellow Light green Magenta Lavender Pink Dark green CTO 2700K Blue Orange CTO 3200K White step 128-129 Positioning Colour wheel Deep Red 130-134 Deep Blue...
Page 19
Mode 1 Mode 2 Fade Type Function Dmx Value Zoom & Focus & Time of frost movement (0.1 sec -->10 sec) 51-100 Frost & Prism time Time of zoom/ focus movement (0.1 sec-->25.5 sec.) 101-255 No function 0-19 Proportional indexing 20-127 Effect wheel Ramping from open to full position ( max.-->min.
Page 23
Mode 1 Mode 2 Fade Type Function Dmx Value Beam shaper 3 28-31 Beam shaper Beam shaper 4 32-35 selection Reserved 36-255 Beam shaper indexing - set position on channel 29/27 Shaper indexing 0 - 255 Beam shaper rotation - set position on channel 29/27 Beam shaper rotation and No rotation...
9.Maintance and cleaning DANGER:Disconnect from the mains before starting any maintenance work. Ballast Please change timely when each pin is getting yellow. Be sure to maintain the device every 2 months,and make sure that all parts of the ballast,such as,scre- ws,terminals,are locked well to ensure performance.Neglecting of maintenance may lead to failure of devices.