Product Description - Wieland Samos Pro Compact SP-COP1 Instruction Manual

3

Product description

3.1 Description
3.1.1 Main module SP-COP1 / SP-COP2-ENx
The COMPACT-module SP-COPx is the CPU of the whole system, in
which all signals are monitored and logically processed according to
the configuration saved on the removable storage SP-COP-CARD1.
The module provides save inputs and outputs, as well as test signal
outputs. As a result of processing the outputs of the system are
switched. This means the internal safety-bus serves as data inter-
face.The removable storage SP-COP-CARD1 has to be ordered
separately.
Attention: Attention:
Attention: Attention:
Commonly available SD cards cannot be used/inserted in sa-
mosPRO and COMPACT modules.
The main module has a mini-USB-bus with the following functions:
Transmission of the configuration of samos
COP-Card1
Read configuration of SP-COP-Card1 in samosPLAN5+
Diagnosis of samos ® PRO system with samosPLAN5+
Online monitoring of samos
The main module SP-COP2 ENx has a RJ45-socket with the same
functions. Additional diagnosis of samos
ed SPS
Attention: there can only be one connection to samos Attention:
Attention: Attention:
the same time (mini-USB or RJ45).
The main module SP-COPx hast four test signal outputs T1 ...T4.
Short circuit detection Short circuit detection Short circuit detection Short circuit detection
SP-COPx detects short circuits between the two
test-outputs T1... T4, if the duration of the test
pulses is < 4 ms.
WARNING WARNING
WARNING WARNING
If the duration of the test pulses is ≥ 4 ms, short
circuits between the test-outputs may remain
undetected.
3.2 Indicators
3.2.1 Indicator Power / Error code (PWR/EC)
PWR/EC-LED
red blinking (1 Hz)
☼
green blinking (1 Hz)
☼
green
8 8 8 8
® PLAN5+ to the SP-
® PRO system
® PRO system via connect-
® PLAN5+ at
Description
An error has occurred in the
controller. All 24 V outputs are
switched. The control system must
be restarted with a power-on reset,
after correcting the cause of the
error
The power supply to A1, B1 or B2
is outside the range of 16.8 V to
30 V.
The power supply to A1, B1, and
B2 is within the range of 16.8 V to
30 V.
3.2.2 Indicator Modul State (MS)
MS-LED
red blinking (1 Hz)
☼
green blinking (1 Hz)
☼
green
☼ / ☼ red / green blinking
3.2.3 Indicator configuration(CV)-LEDs
Code Verified-LED (CV)
yellow blinking (1 Hz)
☼
yellow
3.2.4 Indicator Ethernet-(NET) LED (only SP-COP3-ENx)
Ethernet connection
green blinking (2 Hz)
☼
3.2.5 Indicator Input LEDs
Input Input Input Input- - - - LED LED LED LED
Green flashing (1 Hz)
☼
Green flashing, alter-
☼
nating or synchronous
(1 Hz)
○
Off
Green
3.2.6 Indicator Output LEDs
Output Output Output Output- - - - LED LED LED LED
Green flashing (1 Hz)
☼
○
Off
Green
Description
no project on the keypad or project
data incorrectly (for example:
number of inserted IO-modules
does not match the project)
Project data taken from IO-
modules; waiting for start com-
mand
Controller started
One or more inputs have a cable
break or short-circuit at 24 V.
Or there is a se-
quence/synchronous time error at
a two-channel input.
Or an output has a test error (e.g.
short-circuit).
Description
Project on controller not verified.
Controller does not start automati-
cally after Power-On Reset.
Project on controller is verified.
Controller starts automatically after
Power-On Reset.
Description
While connecting the LED is
blinking for 3 sec.
Bedeutung Bedeutung Bedeutung Bedeutung
A single-channel input has a test
error (cable break or short-circuit
at 24 V) or the input was not
configured in the project and
24 V is pending.
Two-channel input has synchro-
nous time error or a sequencing
error or at least one of the two
inputs has a test error (cable
break or short-circuit at 24 V)
Signal level at the input terminal
is 0 V
Signal level at the input terminal
is 24 V
Bedeutung Bedeutung Bedeutung Bedeutung
Output has a test error
Output is switched off
Output is switched on