Pioneer RMX-1000 Service Manual page 43

5
• Pin Function
No. Name
51 AVSS
52 P157/ANI15
53 P156/ANI14
54 P155/ANI13
55 P154/ANI12
56 P153/ANI11
57 P152/ANI10
58 P151/ANI9
59 P150/ANI8
60 P27/ANI7
61 P26/ANI6
62 P25/ANI5
63 P24/ANI4
64 P23/ANI3
65 P22/ANI2
66 P21/ANI1
67 P20/ANI0
68 P130
69 P131/TI06/TO06
70 P04/SCK10/SCL10
71 P03/SI10/RxD1/SDA10
72 P02/SO10/TxD1
73 P01/TO00
74 P00/TI00
75 P145/TI07/TO07
76 P144/SO20/TxD2
77 P143/SI20/RxD2/SDA20
78 P142/SCK20/SCL20
79 P141/PCLBUZ1/INTP7
80 P140/PCLBUZ0/INTP6
81 P120/INTP0/EXLVI
82 P47/INTP2
83 P46/INTP1/TI05/TO05
84 P45/SO01
85 P44/SI01
86 P43/SCK01
87 P42/TI04/TO04
88 P41/TOOL1
89 P40/TOOL0
90 RESET
91 P124/XT2
92 P123/XT1
93 FLMD0
94 P122/X2/EXCLK
95 P121/X1
96 REGC
97 VSS
98 EVSS0
99 VDD
100 EVDD0
5
6
for RMX-1000 I/O
GND (AD/DA)
VR_PARAM1 I [AD] "SUB PARAMETER1" VR voltage
VR_HI I [AD] "HI" VR voltage
VR_LEVEL I [AD] "LEVEL" VR voltage
VR_PITCH I [AD] "PITCH" VR voltage
VR_LOW I [AD] "LOW" VR voltage
VR_MID I [AD] "MID" VR voltage
VR_OUTPUT I [AD] "OUTPUT LEVEL" VR voltage
VR_PARAM2 I [AD] "SUB PARAMETER2" VR voltage
VR_RELEASE_FX I [AD] "RELEASE FX" resistance-type sensor voltage
VR_SCENE_FX I [AD] "SCENE FX" VR voltage
O Not used, set to output port
O Not used, set to output port
O Not used, set to output port
O Not used, set to output port
O Not used, set to output port
O Not used, set to output port
O Not used
SCENE_LED_RED O For exclusive use of SCENE VR an LED lighting signal RED PWM output
DBG_PORT3 O Land port for microcomputer debugging (connect to GND)
DBG_PORT2 O Land port for microcomputer debugging (connect to GND)
DBG_PORT1 O Land port for microcomputer debugging (connect to GND)
DBG_PORT0 O Land port for microcomputer debugging (connect to GND)
O Not used, set to output port
SCENE_LED_BLUE O For exclusive use of SCENE VR an LED lighting signal BLUE PWM output
CPU_MVR_MUTE O Control signal output for audio mute
STBY_LED_SEL I/O Control signal of the LED to be able to light in power supply STBY
after the overvoltage detection
ADP_XDET I AC adapter plug insertion detection signal input
FAULT_DET I Voltage detection signal input
FET_SW_ADP O Control signal output for the power supply ON/OFF FET
except the STB power supply
O Not used, set to output port
K0R_CTRL I Communication with SH (reserve)
K0R_INT O Be required an interrupt to SH
K0R_TXD O Send serial data to SH
K0R_RXD I Receive serial data from SH
K0R_SCK O Send serial clock to SH
SH_RESET O SH reset signal
TOOL1 O Clock output for debuggers
TOOL0 O Flash memory programmer / Data input and output for debuggers
MAIN_RST I Reset cancellation signal input from RESET IC
I Not used
I Not used
FLMD0 - Draw a flash memory programming mode
X2 Connect to oscilator for main system clock (20 MHz)
X1 Connect to oscilator for main system clock (20 MHz)
Regulator output for internal operation (2.5 V),
stable capacity connection, Connect to GND via 1uF
GND (P121-124, except port section, RESET, except FLMD0)
GND (port section, RESET, FLMD0)
Power supply 3.3 V (P121-124, except port section, RESET, except FLMD0)
Power supply 3.3 V (port section, RESET, FLMD0)
RMX-1000
6
7
Function
7
8
A
B
C
D
E
F
43
8