Pioneer RMX-1000 Service Manual page 28

1
A
[9] USB communication error
No. Cause Diagnostics Point
9-1 USB cable USB cable
prior confirmation
9-2 Defective USB_D+, USB_D-
USB circuit
B
[10] Reading/writing error of an SD card
No. Cause Diagnostics Point
10-1 Defective SD_CLK, SD_CMD,
SD circuit SD_DATA0,
SD_DATA1
10-2 Improper SD_LED,
sampler data SD memory card
C
[11] Failure in the RELEASE FX lever
No. Cause Diagnostics Point
11-1 Calibration NG RELEASE FX lever
LED
11-2 Defective parts RELEASE FX lever
D
RELEASE FX mechanism parts
lever mechanism
11-3 FFC SPFX Assy -
prior confirmation PARAM Assy FFC
11-4 Defective parts RELEASE FX lever
SPFX Assy LED
E
[12] Be displayed with [Err] in 7-segment
No. Cause Diagnostics Point
12-0 (Work on cause 7-segment indication Eject an SD card.
rearranging)
12-1 Illegal SD card
customized data
F
12-2 Defective MAIN Assy:
SH UCOM, FLASH_CLK,
FLASH Memory FLASH_SI
28
1
2
Item to be Checked
Check that USB cable is securely
connected.
Check that this is no breakage in the
USB cable.
Connect this unit with a PC and check that
it can be recognized by the PC.
Check that the proper waveform is output
from each point.
Item to be Checked
Connect this unit with a PC and check that
the SD card can be recognized as a
removable disc and that its content can be
viewed from the PC.
Check that the SD_LED is lit or flashing at
intervals of 1 sec.
Check that the sampler data are in
conformity with the WAV format (48 kHz,)
which this unit can use.
Ask the customer if the sampler data in
question were exported with the use of
RemixBox.
Item to be Checked
Check that lighting of the LEDs is properly
performed in correspondence with
movement of the RELEASE FX lever.
Check that all components of the
RELEASE FX lever are properly
assembled and that they are not damaged.
Check that FFC is securely connected.
Check that this is no breakage in the
FFC.
Check that all components of the
RELEASE FX lever are properly
assembled and that they are not damaged.
Item to be Checked
Ask the customer if the sampler data in
question were exported with the use of
RemixBox.
Check for the correct waveforms output
from each points.
RMX-1000
2
3
Corrective Action
Securely connect the USB cable.
If the USB cable is broken, replace it.
L2515 or JA2501 may be defective.
Replace it.
Terminal of IC7002 may be defective.
Replace it.
Corrective Action
CN2502 may be defective.
Replace it.
Terminal of IC7002 may be defective.
Replace it.
Create sampler data, using RemixBox.
Corrective Action
Recalibrate the lever.
Reassemble the components properly.
If any component is damaged,
replace it.
Recalibrate the lever.
Securely connect the FFC.
If the FFC is broken, replace it.
Recalibrate the lever.
VR7601, D7601 to D7603 may be
defective. Replace it.
Recalibrate the lever.
Corrective Action
If "ERR" indication disappears, go to 12-1.
If "ERR" indication is unchanged, go to 12-2.
Create sampler data, using RemixBox.
IC2501 or IC2502 may be defective.
Replace it.
3
4
Reference
5.5 USB DIAGNOSIS
METHOD
5.5 USB DIAGNOSIS
METHOD
10.16 WAVEFORMS
30 31
Reference
—————
5.4 ERROR INDICATION
Reference
1.4 ABOUT THE CALIBRATION
OF RELEASE FX LEVER
6.1 TEST MODE
6.2 CALIBRATION MODE
1.4 ABOUT THE CALIBRATION
OF RELEASE FX LEVER
6.1 TEST MODE
6.2 CALIBRATION MODE
9. EXPLODED VIEWS AND
PARTS LIST
1.4 ABOUT THE CALIBRATION
OF RELEASE FX LEVER
4.1 OVERALL WIRING
DIAGRAM
6.1 TEST MODE
6.2 CALIBRATION MODE
1.4 ABOUT THE CALIBRATION
OF RELEASE FX LEVER
6.1 TEST MODE
6.2 CALIBRATION MODE
Reference
5.4 ERROR INDICATION
5.4 ERROR INDICATION
10.16 WAVEFORMS
18 19
4