Summary of Contents for RH Teen CALLUM 6-DRAWER TWIN/FULL STORAGE CANOPY BED
Page 1
CAL LU M 6 - D RAWER T WI N / FU LL STO RAGE CA NO P Y B ED PARTS I N CLU DE D: ITEM DESCRIPTION QTY. HEADBOARD PANEL Long Bolt 5/16” x 2-1/4” 20 pcs. HEADBOARD POSTS FOOTBOARD POSTS 20 pcs.
CA L LU M 6 - D R AWE R T W IN / F U LL STO RAGE CA N OP Y BE D STEP 2: Attach the Short Side Rails (E) to the Side Drawer Frame (D) using Short Screws (5), and tighten with Philips Head Screwdriver (not included).
Page 3
CA L LU M 6 - D RAWER T WI N / FU LL STO RAGE CA N O PY BE D STEP 4: Attach the Headboard Posts (B) and Footboard Posts (C) to the Bed Base. Note: - Bolts on Headboard/ Footboard are located in the 1st and 3rd bolt locations.
Page 4
CA L LU M 6 - D R AWE R T W IN / F U LL STORAGE CA N OP Y BE D STEP 6: Insert the Connecting Bolt (7) into the bottom of the Side Drawer Frame (E). STEP 7: Please carefully pull the drawers out of the Storage Base (F) by pulling on the cut-outs...
Page 5
CAL LU M 6 - D RAWER T WI N / FU L L STO RAGE CA NO P Y B ED STEP 8: Attach the Support Legs (H) into the bottom of the Storage Base (F). STEP 9: Lay the Storage Base (F) inside the assembled Bed Base.
Page 6
CA L LU M 6 - D RAWER T WI N / F U LL STO RAGE CA N O PY BE D STEP 10: Attach the Storage Base (F) to the Side Drawer Frame (D). Place Camlock Wheel (8) into the holes inside of Storage Base (F) by aligning the arrow sign on the Camlock Wheel (8) with the Connecting Bolts (7) and twist clockwise to tighten using Allen...
Page 7
CA L LU M 6 - D RAWE R T WI N / F U LL STO RAGE CA NO P Y BED NOTE: - MAKE SURE THE CANOPY RAILS ARE PUT TOGETHER BEFORE PLACING ON TOP OF THE POSTS. - ASSEMBLING THE CANOPY: INSERT ALL BOLTS BEFORE FULLY TIGHTENING ALL 4 CORNERS.
Page 8
CA L LU M 6 - D R AW ER T WI N / FU LL STO RAGE CA N O PY BE D ASSEMBLY ALERT - MENDING PLATES SHOULD ONLY BE ATTACHED WHEN BED IS DELIVERED AND ASSEMBLED IN HOME. THEY SHOULD NOT BE ATTACHED DURING PRE-INSPECTION BY DELIVERY AGENTS.
Page 9
CAL LU M 6 -D RAW ER T WI N / F U LL STO RAGE CA NO P Y BED STEP 15: Attach Metal Brackets (16) onto the top of the canopy bed with Screws 7x20 mm (17), using Phillips-Head Screwdriver to tighten, (as shown below).
CA L LU M 6 - D R AWE R T W I N /F U LL STOR AGE CA N OP Y BE D STEP 17: Insert drawers into the Storage Base (F). Assembly is completed. CARE INSTRUCTIONS: Dust often using a clean, soft, dry lint-free cloth. Blot spills immediately, and wipe with a clean, damp cloth.
Page 11
CA L LU M 6 - D RAWE R QU E EN STO RAGE CAN O PY BE D PARTS I N CLU DE D: ITEM DESCRIPTION QTY. HEADBOARD PANEL Long Bolt 5/16” x 2-1/4” 20 pcs. HEADBOARD POSTS FOOTBOARD POSTS 20 pcs.
Page 12
CA L LU M 6 - D R AWE R Q U EEN STOR AGE CA N OP Y BE D STEP 2: Attach the Short Side Rails (E) to the Side Drawer Frame (D) using Short Screws (5), and tighten with Philips Head Screwdriver (not included).
Page 13
CAL LU M 6 - D RAWER Q U EEN STOR AGE CA N OP Y BE D STEP 4: Attach the Headboard Posts (B) and Footboard Posts (C) to the Bed Base. Note: - Bolts on Headboard/Footboard are located in the 1st and 3rd bolt locations. - Bolts on the Side Rails are located in the 2nd and 4th hole locations.
Page 14
CA LLU M 6 - D RAWER Q U EEN STOR AGE CA N OP Y BE D STEP 6: Insert the Connecting Bolt (7) into the bottom of the Side Drawer Frame (D). STEP 7: Please carefully pull the drawers out of the Storage Base (F) by pulling on the cut-outs on drawer fronts.
Page 15
CA L LU M 6 - D R AWE R QU EEN STOR AGE CA N OP Y BE D STEP 8: Attach the Support Legs (H) into the bottom of the Storage Base (F). STEP 9: Lay the Storage Base (F) inside the assembled Bed Base.
Page 16
CA L LU M 6 - D R AW E R Q U EEN STO RAGE CA NO P Y B ED STEP 10: Attach the Storage Base (F) to the Side Drawer Frame (D). Place Camlock Wheel (8) into the holes inside of Storage Base (F) by aligning the arrow sign on the Camlock Wheel (8) with the Connecting Bolts (7) and twist clockwise to...
Page 17
CA LLU M 6 - D RAWER Q U EEN STOR AGE CA N OP Y BE D NOTE: - MAKE SURE THE CANOPY RAILS ARE PUT TOGETHER BEFORE PLACING ON TOP OF THE POSTS. - ASSEMBLING THE CANOPY: INSERT ALL BOLTS BEFORE FULLY TIGHTENING ALL 4 CORNERS. STEP 12: Insert the Connecting Bolts (12) into the Short Canopy Rails (J).
Page 18
CAL LU M 6 - D R AWE R QU EEN STO RAGE CA NO P Y BE D ASSEMBLY ALERT - MENDING PLATES SHOULD ONLY BE ATTACHED WHEN BED IS DELIVERED AND ASSEMBLED IN HOME. THEY SHOULD NOT BE ATTACHED DURING PRE-INSPECTION BY DELIVERY AGENTS. - PLEASE USE A LADDER WHILE ASSEMBLING THE CANOPY AND METAL BRACKETS.
Page 19
CA LLU M 6 - D RAWE R QU E EN STORAGE CA N OP Y BE D STEP 15: Attach Metal Brackets (16) onto the top of the canopy bed with Screws 7x20 mm (17), using Phillips-Head Screwdriver to tighten, (as shown below).
Page 20
CA L LU M 6 - D R AW E R Q U EEN STOR AGE CA N OP Y BE D STEP 17: Insert drawers into the Storage Base (F) and assembly is completed. CARE INSTRUCTIONS: Dust often using a clean, soft, dry lint-free cloth. Blot spills immediately, and wipe with a clean, damp cloth.