Advertisement

Table of Content
1. Post Leg Installation ('P' option)..........................................................................2
2. T & C - Leg Installation (T & C options)..............................................................4
3. T & C - Adjustable Leg Installation (A + D option)..............................................7
4. Flip Top Leg & Assembly Installation (DT5A Product)......................................10
5. 4X Leg Installation (X - option).........................................................................14
6. Single Column Leg Installation (S option)........................................................17
7. Y3 Leg Installation (E option)............................................................................21
8. Y2 Leg Installation (G option)...........................................................................24
9. Byrne Interlink...................................................................................................27
10. Extended Meeting Table..................................................................................28
Z
© 2019 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
Y, L, Everywhere Tables are among the trademarks of Herman Miller, Inc.
TM
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
1
B
6
K
0
D
Part no. 1b6k0d rev G
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Everywhere Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for HermanMiller Everywhere Series

  • Page 1: Table Of Contents

    Table of Content 1. Post Leg Installation (‘P’ option)................2 2. T & C - Leg Installation (T & C options)..............4 3. T & C - Adjustable Leg Installation (A + D option)..........7 4. Flip Top Leg & Assembly Installation (DT5A Product)........10 5.
  • Page 2: Post Leg Installation ('P' Option)

    Everywhere Tables Post Leg Installation (P) ™ and Disassembly for Recycling Instructions Parts Included: Post Leg Option (2 Sets) Machine Star Pan Head Tapping Screw (4) Washer (4) Screw (40) For Painted MDF Tops Only Hardware Pack Tools Required: Work Surface Options Safety Glasses #2 Phillips Bit Power Driver...
  • Page 3 Assembly Instructions: 1. Align Holes in Post Legs (B) with outermost holes in Work Surface (A). 2. Install 8 Pan Head Tapping Screws (C) per Leg (HPL + Veneer) or 7 pan head Screws per leg (C) (Painted MDF). 3. For use on ‘painted MDF tops’ use (D)+(E) in locations where an insert is present in the hole pattern.
  • Page 4: T & C - Leg Installation (T & C Options)

    Everywhere Tables T & C Leg Installation (T & C options) ™ and Disassembly for Recycling Instructions Parts Included: T Leg Option (2 Sets) Work Surface Options C Leg Option Machine Star Pan Head Tapping Connection Hex Flange Tapping Screw (2) Washer (2) Screw (32) Bracket (2)
  • Page 5 Assembly Instructions: B or C Notch B or C Hook 1. Hold Leg segments (B or C) at 15 degree angle to one another. 2. Insert Hooks on base of leg segments into notches in adjoining leg segments. 3. Secure Leg segments together with Connection Bracket (D) and 2 Hex Flange Tapping Screws (E).
  • Page 6 Disassembly for Recycling: Materials Identification and Segregation: Where possible, plastic components are marked with ASTM recycling codes. Use these codes to identify material type for recycling. Non marked components should be treated as mixed plastic. Ferrous metals can be identified using a small magnet for recycling.
  • Page 7 Everywhere Tables Adjustable Leg Table Installation ™ (A + D options) and Disassembly for Recycling Instructions Parts Included: T Adjustable Leg C Adjustable Leg Option (2 Sets) (A) Option (D) Work Surface Options Machine Star Pan Head Tapping Connection Hex Flange Tapping Screw (2) Washer (2) Screw (32)
  • Page 8: T & C - Adjustable Leg Installation (A + D Option)

    Assembly Instructions: Adjustable Leg Installation: “T” Leg “C” Leg Foot Assembly Foot Assembly 1. Secure leg segments together with connecting bracket (D) and 2 Hex Flange tapping screws (E) (per leg assembly). 2. Position Leg Assembly at each end on bottom side of Work Surface (A) so that Foot Assembly is centered on depth of Work Surface.
  • Page 9 Disassembly for Recycling: Materials Identification and Segregation: Where possible, plastic components are marked with ASTM recycling codes. Use these codes to identify material type for recycling. Non marked components should be treated as mixed plastic. Ferrous metals can be identified using a small magnet for recycling.
  • Page 10: Flip Top Leg & Assembly Installation (Dt5A Product)

    Everywhere Tables Flip - Top Table Installation ™ and Disassembly for Recycling Instructions Parts Included: Work Surface Options Leg Assembly (2) Cross Member Assembly Paddle (2) Pan Head Tapping Assembly 1.5” long screws(8) Pan Head Tapping Hex Flange Tapping Connection Screw 3/4”...
  • Page 11 Assembly Instructions: Notch Hook 1. If legs have casters, use 1-locking caster and 1-non locking caster per leg assyembly. 2. Hold Leg segments (B) at 15 degree angle to one another. 3. Insert Hooks on base of leg segments into notches in adjoining leg segments. 4.
  • Page 12 Flip Top Assembly 8. Position Flip Top Assembly onto Work Surface (A). 9. Install 8 Pan Head Tapping Screws 3/4” long (H). (Polished Aliminum retaining bracket) (Paddle) Flip Top Assembly 10. Position Paddles (D) up against Collars on Cross Members. 11.
  • Page 13 Disassembly for Recycling: Materials Identification and Segregation: Where possible, plastic components are marked with ASTM recycling codes. Use these codes to identify material type for recycling. Non marked components should be treated as mixed plastic. Ferrous metals can be identified using a small magnet for recycling.
  • Page 14: Leg Installation (X - Option)

    Everywhere Tables 4 X (X - Option) Installation ™ and Disassembly for Recycling Instructions Parts Included: 4-Way Base T Leg (4) Connector Work Surface Options Hex Flange Tapping Pan Head Tapping Connection Screw (5) Screw (32) Bracket (2) Tools Required: Power Driver Ratchet Wrench #2 Phillips Bit...
  • Page 15 Assembly Instructions: 1. Hold Leg segments(B) at 15 degree angle. 2. Interlock Leg Bases onto Base Connector(C). 3. Position Leg Assembly onto bottom of Table Top(A). 4. Install 8 screws(F) per Leg. 5. Tie Legs together with 2 Leg Brackets(D) and 5 Hex Flange Screws(E). Do not overtighten.
  • Page 16 Disassembly for Recycling: Materials Identification and Segregation: Where possible, plastic components are marked with ASTM recycling codes. Use these codes to identify material type for recycling. Non marked components should be treated as mixed plastic. Ferrous metals can be identified using a small magnet for recycling.
  • Page 17: Single Column Leg Installation (S Option)

    Everywhere Tables Single Column Base (S) ™ Installation and Disassembly for Recycling Instructions Parts Included: Pan Head Tapping Hex Nut(2) Screw (4) Flat Washer Lock Washer(2) Hardware Pack 4-Leg Base Spider Work Surface Options Lock Ring Leg Extrusion Threaded Rod Tools Required: Safety Glasses Power Driver...
  • Page 18 Assembly Instructions: 1. Assemble 4-leg base(G) together. 2. 4 Leg Bases(G) fit into Leg Extrusion(B). 0.125” 3. Assemble Lock Ring(E) to bottom of Leg base(G). 4. Insert Threaded Rod(C) with Lock Washer(L) & Hex Nut(J) at bottom of Leg Base(G). Part no.
  • Page 19 Pins 5. Assemble Cap(D) on top of Leg Extrusion(N). 6. Place Spider(F) on top of Cap(D). Make sure pins are in holes in Spider(F). 7. Place Flat Washer(K), Lock Washer(L) and Hex Nut(J) to top of Threaded Rod(C). Tighten. 8. Using Pan Head screw(H) assemble Work Surface(A) with Leg Base assembly.
  • Page 20 Disassembly for Recycling: Materials Identification and Segregation: Where possible, plastic components are marked with ASTM recycling codes. Use these codes to identify material type for recycling. Non marked components should be treated as mixed plastic. Ferrous metals can be identified using a small magnet for recycling.
  • Page 21: Y3 Leg Installation (E Option)

    Everywhere Tables Y3 Leg Installation (E-option) ™ Installation and Disassembly for Recycling Instructions Parts Included: 3-Way Base Work Surface Options T Leg (6) Connector (2) Pan Head Hex Flange Tapping Tapping Leg Connector (2) Screw (48) Screw (6) Hardware Pack Options Tools Required: Safety Glasses Power Driver...
  • Page 22 Assembly Instructions: 1. Hold Leg segments(B) at 15 degree angle. 2. Interlock Leg Bases onto Base Connector(C). 3. Position Leg Assembly onto bottom side of Work Surface(A) 4. Install 24 Pan Head Tapping Screws(E) per leg assembly. 5. Position Y Brace(D) onto Leg Assemblies. 6.
  • Page 23 Disassembly for Recycling: Materials Identification and Segregation: Where possible, plastic components are marked with ASTM recycling codes. Use these codes to identify material type for recycling. Non marked components should be treated as mixed plastic. Ferrous metals can be identified using a small magnet for recycling.
  • Page 24: Y2 Leg Installation (G Option)

    Everywhere Tables Y2 Leg Installation ™ and Disassembly for Recycling Instructions Parts Included: 3-Way Base Connector (2) Work Surface Options T Leg (4) Leg Spanner (1) Pan Head Hex Flange Tapping Tapping Leg Connector (2) Screw (32) Screw (8) Hardware Pack Options Tools Required: Safety Glasses Power Driver...
  • Page 25 Assembly Instructions: 1. Hold Leg segments (B) at 15 degree angle. 2. Interlock Leg Bases onto base connector(C). 3. Assemble Leg Connectors onto bottom of Leg Assemblies with 2 Hex Flange Tapping Screws(G) per leg. 4. Install Leg Assemblies onto Work Surface(A) with 32 Tapping Screws(F). Part no.
  • Page 26 Tapping Screws 5. Attach spanner (D) to the two leg connectors (E), use 4 Hex flange tapping screws (G). Do not overtighten Disassembly for Recycling: Materials Identification and Segregation: Where possible, plastic components are marked with ASTM recycling codes. Use these codes to identify material type for recycling. Non marked components should be treated as mixed plastic.
  • Page 27: Byrne Interlink

    Electrically interconnected tables shall be mechanically connected. Part no. 1b6k0d rev G © 2019 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A. Y, L, Everywhere Tables are among the trademarks of Herman Miller, Inc. Illustrations and specifications are based on the latest product information available at the time of publication. The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
  • Page 28: Extended Meeting Table

    Everywhere Soft Rectangle - Extended Meeting Table Installation and Disassembly for Recycling Instructions Parts Included: Y2 Leg Option Post Leg Option Y Leg Option Work Surface (2) Leg kit (2) Stiffener (Post Leg Joint 3-Way Base Ganging Plate (2) Biscuit (4) Fastener (4) Connector configuration only)
  • Page 29 Assembly Instructions: Step 1: Lay work surfaces (A) upside down on a soft surface to prevent scratching. Step 2: Assemble legs using instructions specified in this document. The leg configuration can be determined based on the images below: Y2 Leg Option Part no.
  • Page 30 Tapping Screws Part no. 1b6k0d rev G © 2019 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A. Y, L, Everywhere Tables are among the trademarks of Herman Miller, Inc. Illustrations and specifications are based on the latest product information available at the time of publication. The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
  • Page 31 Y3 Leg Option Step 3: Locate the predrilled holes for leg configuration and attach the leg assemblies to the work surface using the included hardware Part no. 1b6k0d rev G © 2019 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A. Y, L, Everywhere Tables are among the trademarks of Herman Miller, Inc.
  • Page 32 Step 4: Carefully flip each table onto its feet. Align each joint edge. Attach joint connectors using a small allen wrench to tighten until the joint is gap free. Attach the ganging plate in the pre-drilled holes in the work surface. Part no.
  • Page 33 Disassembly for Recycling: Materials Identification and Segregation: Where possible, plastic components are marked with ASTM recycling codes. Use these codes to identify material type for recycling. Non marked components should be treated as mixed plastic. Ferrous metals can be identified using a small magnet for recycling.

Table of Contents

Save PDF