Nautilus Hyosung MONiMAX8800 Installation Manual
  1. Manuals
  2. Brands
  3. Nautilus Hyosung Manuals
  4. Cash Counter
  5. MONiMAX8800
  6. Installation manual

Nautilus Hyosung MONiMAX8800 Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Installation Manual
MONiMAX8800 System
V01.00.03 (2016.02.25)
© 2016 Nautilus Hyosung Inc. All Rights Reserved.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MONiMAX8800 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Nautilus Hyosung MONiMAX8800

Summary of Contents for Nautilus Hyosung MONiMAX8800

  • Page 1 Installation Manual MONiMAX8800 System V01.00.03 (2016.02.25) © 2016 Nautilus Hyosung Inc. All Rights Reserved.
  • Page 2 Modify the image of Fascia Item Locations for Voice Chapter3 Guidance © 2016 Nautilus Hyosung All Rights Reserved. The content of this specification is protected by copyright laws. 2016. 2. 25. 4th Release © 2016 Nautilus Hyosung Inc. All Rights Reserved.

  • Page 3: Table Of Contents

    Removing the locking section from the main body of Cash & Check In Module ........B-7 Separating the Cassette Section ......................B-8 Installing Section............................. B-9 Setting the Casters for Cash & Check In Module ..................B-12 Notes ............................Notes-1 © 2016 Nautilus Hyosung Inc. All Rights Reserved.

  • Page 4: Chapter1. Preface

    ▶ If any question or installation error occurs while preparing for and installing MX8800 in compliance with this manual, please contact maintenance staffs of Nautilus Hyosung. For the contact of maintenance staffs of Nautilus Hyosung, see the E-mail addresses and telephone numbers provided separately.

  • Page 5: Terminologies

    Chapter1. Preface Installation Manual It is the policy of Nautilus Hyosung Inc to improve products as new technology, components, software, and firmware become available. Therefore Nautilus Hyosung. reserves the right to change specifications without notice. Terminologies ▶ In this document the terminology listed below is used as follows: ▪...
  • Page 6 Magnetic Card Unit Operation Panel for Customers to Operate OSD board On Screen Display Board Power Supply Personal Identification Number Panel Control Board Endorsement Module Printer (mainly Receipt Printer) Recycling Box Unit Recycle Cassette © 2016 Nautilus Hyosung Inc. All Rights Reserved.
  • Page 7 RT/A6 Retract & A6 Cassette Switch Separator Control Module Sensor and Indications Unit Service Provider Slip Printer (Receipt Printer) Tape Escrow Text Terminal Unit (OPL or SPL) Utility Cassette Vacuum Fluorescent Display © 2016 Nautilus Hyosung Inc. All Rights Reserved.

  • Page 8: Safety Precautions

    4. The equipment is to be secured to the building structure before operation 5. A security container shall be permitted to optionally be provided with a secondary lock, but improper use of the secondary lock feature will reduce the security level of the ATM. © 2016 Nautilus Hyosung Inc. All Rights Reserved.
  • Page 9 ▪ If the above-mentioned abnormalities occur, immediately turn off the power, unplug the equipment and contact the service center. ▪ If you ignore these symptoms, the equipment may catch on fire or cause electric shock. © 2016 Nautilus Hyosung Inc. All Rights Reserved.

  • Page 10: Related Document

    ▶ The related documents are listed as follows. If needed, please contact staffs of our technical support team and maintenance team. ▪ Operator Manual ▪ Service Manual ▶ For the contact of maintenance staffs of Nautilus Hyosung, see the E-mail addresses and telephone numbers provided separately. © 2016 Nautilus Hyosung Inc. All Rights Reserved.

  • Page 11: Chapter2. Introduction

    Nautilus Hyosung’s intuitive and easy UI. Supports expanded options such as coin dispenser, RF (NFC), and 2D barcode, as well as basic functions of deposit/withdrawal of cash/check. Allows easy and quick installation and maintenance. © 2016 Nautilus Hyosung Inc. All Rights Reserved.

  • Page 12: System Identification Label

    Chapter2. Introduction Installation Manual System Identification Label ▶ The System Label below shows the layout of the product identification label which is fixed inside the ATM © 2016 Nautilus Hyosung Inc. All Rights Reserved.

  • Page 13: Chapter3. Atm Installation

    Chapter3. ATM Installation System Layout & Dimensions <Note!> All measurements in this section are in inches with metric provided in braces ( ). ► Dimensions of MX8800 with the teller operation panel folded. © 2016 Nautilus Hyosung Inc. All Rights Reserved.
  • Page 14 Chapter3. ATM Installation Installation Manual ► The following diagrams show the dimensions of MX8800 with the teller operation panel unfolded. ► The following diagrams show the dimensions of MX8800 on plane view. © 2016 Nautilus Hyosung Inc. All Rights Reserved.

  • Page 15: Height And Depth Main Fascia Items

    ATM is in use. The top of the touch screen is considered to be the highest operable point of this ATM. According to the Nautilus Hyosung’s software application guideline, the height of contents touchable on the screen is lower than 838.2 mm [33.00 inch], respectively, satisfying the ADA standard.
  • Page 16 The depths of each unit, measured from the frontlets of the front are marked with symbols and detailed in the above table. That satisfies the ADA standard and allows good accessibility and convenience for both of unhands capped and handicapped people. © 2016 Nautilus Hyosung Inc. All Rights Reserved.

  • Page 17: Fascia Item Locations For Voice Guidance

    Installation Manual Chapter3. ATM Installation Fascia Item Locations for Voice Guidance ▶ Fascia Item Locations for Voice Guidance. © 2016 Nautilus Hyosung Inc. All Rights Reserved.

  • Page 18: Unpacking The Atm

    4. Verify the contents carefully with the packing list to be sure all items listed are included. Notify your distributor of any shortages. 5. If only the palette needs to be removed, lift the whole machine from the bottom and set it aside. © 2016 Nautilus Hyosung Inc. All Rights Reserved.

  • Page 19: Installation And Service Clearance

    <Note!> All measurements in this section are in inches with metric provided in braces ( ). ► Following diagram is describing the areas required for installing and servicing the MX8800 with Coin Dispenser, SPR, BRM and CCIM taken out from the ATM © 2016 Nautilus Hyosung Inc. All Rights Reserved.
  • Page 20 Chapter3. ATM Installation Installation Manual © 2016 Nautilus Hyosung Inc. All Rights Reserved.

  • Page 21: Bolting Down The Mx8800

    4. With the groove of the anchor bolt facing up, drive the anchors into the holes drilled in step 3. 5. Place the MX8800 on the bolt location sheet, matching the mounting holes of the unit with the anchors. 6. Firmly tighten the mounting bolts in the anchors. © 2016 Nautilus Hyosung Inc. All Rights Reserved.
  • Page 22 Installation Manual ► Anchor bolts location sheet sample (full view of anchor label for MX8800) <Note!> All measurements in this section are in metric with inches provided in braces [ ]. 3-10 © 2016 Nautilus Hyosung Inc. All Rights Reserved.
  • Page 23 ► Anchor bolts location sheet sample (Detail view of A section in the full view of anchor label for MX8800) <Note!> All measurements in this section are in metric with inches provided in braces ( ). © 2016 Nautilus Hyosung Inc. All Rights Reserved. 3-11...

  • Page 24: Chapter4. System Cable Connection Guide

    The following steps show where the wires (AC Cord & LAN Cable) enter the system. <Note!> 1. LAN Cable means Network Data connection cable connect Machine to network hub. 2. AC CORD means power connection cable. It connects Machine Ac out connecter to Power-In Connecter. © 2016 Nautilus Hyosung Inc. All Rights Reserved.

  • Page 25: System Cable Installation

    ▶ Following figures show the location of leading-in hole for external Interface Cable of Right system on the right when viewed on the front of systems. The external interface cables are AC Cord, LAN Cable, Alarm & Camera Cable and etc. © 2016 Nautilus Hyosung Inc. All Rights Reserved.

  • Page 26: Terminal Block Pin Interface Specification

    1. Alarm Signal Cable consists of Seismic, Heat and Door Sensor. (Label stuck inside vault door.) 2. Camera Cable consists of DC12V and Video Signal. (Label stuck on Camera Cable Connection Bracket as "+12V" and "BNC") © 2016 Nautilus Hyosung Inc. All Rights Reserved.

  • Page 27: How To Connect Cables

    Before connecting the AC Cord and LAN Cable, insert the black cap, the Supplementary Component in the attachment box, into the hole. Low Black Cap to be connected to the hole of the side body (Right System) © 2016 Nautilus Hyosung Inc. All Rights Reserved.

  • Page 28: Power

    1. Provided AC Cord - AC Cord (0.35M (13.8inch), 15A, YP-12, L6-15R (Locking Type)) - AC Cord (4.5M (177.2inch), 15A, L6-15P (Locking Type), YC-12) 2. Power Requirement - 1500VA - 120Vac, 12.5A © 2016 Nautilus Hyosung Inc. All Rights Reserved.

  • Page 29: Appendix 1. Supplementary Component

    1. Unpack the attachment Box. 2. The Supplementary Components should have the following items; Item components 3 system keys 6 CCIM keys 4 BRM keys Receipt Roll, Receipt Axis, AC Cord, LAN cable A1-1 © 2016 Nautilus Hyosung Inc. All Rights Reserved.

  • Page 30: Appendix 2. Module Setting

    Phillips Head Screw Driver 150.0mm [5.90inch], Cable Ties (150.0mm [5.90inch], 200.0mm [7.90inh]) 2. OPL Assembly Tools Long Phillips Head Screw Driver (About 300.0mm [11.80inch]), Thin Phillips Head Screw Driver 3. SPL Assembly Tools A2-1 © 2016 Nautilus Hyosung Inc. All Rights Reserved.

  • Page 31: Receipt Printer In The Side Body

    1. Open the side body door with the system key. 2. Remove a yellow screw from the receipt printer base as seen in picture below 3. Remove the receipt printer guide tape as shown in picture below. A2-2 © 2016 Nautilus Hyosung Inc. All Rights Reserved.

  • Page 32: Bill Recycling Module (Brm) In The Safety Body

    2. Unfasten the screws (4ea) to remove the fixing bracket from the upper body of BRM. 3. Unfasten the screws (8ea from the brackets on the top & bottom of lower body) and take out the lower body of BRM. A2-3 © 2016 Nautilus Hyosung Inc. All Rights Reserved.
  • Page 33 Appendix2. Module Setting Installation Manual 4. Unfasten the screws from the fixing bracket (4ea from right and left) and open the Mid Transport Path. 5. Unfasten the screws (3ea) and removed the bracket. A2-4 © 2016 Nautilus Hyosung Inc. All Rights Reserved.
  • Page 34 Installation Manual Appendix2.Module Setting 6. Fasten the screws (3ea) unfastened in the above step as pictured below. 7. Mount the cassettes and close the Mid Transport Path. A2-5 © 2016 Nautilus Hyosung Inc. All Rights Reserved.

  • Page 35: Cash & Check In Module (Ccim) In The Safety Body

    2. Lift up the door and remove the Bubble Bag inside. ▶ Reject Section Remove a tape from the Reject Section. ▶ Bottom Section Remove the desiccant attached on the bottom. A2-6 © 2016 Nautilus Hyosung Inc. All Rights Reserved.

  • Page 36: Removing The Locking Section From The Main Body Of Cash & Check In Module

    ▶ Removing the Lock Lever Tie from the main body, remove the tie from the Lock Section marked in the picture below (9 points). Removing the Lock Lever Tie from the main body A2-7 © 2016 Nautilus Hyosung Inc. All Rights Reserved.

  • Page 37: Separating The Cassette Section

    3. Open the door with the key. Then remove the tape on the bottom of the middle guide. Procedure to remove the protective material from the RT/A6 Cassette Section A2-8 © 2016 Nautilus Hyosung Inc. All Rights Reserved.

  • Page 38: Installing Section

    Installing Section ▶ Installing the Cash & Check & RT/A6 Cassette Section Insert and push the Cash & Check & RT/A6 cassette in body module completely. Then it is locked automatically. A2-9 © 2016 Nautilus Hyosung Inc. All Rights Reserved.
  • Page 39 Appendix2. Module Setting Installation Manual ▶ Installing the PRT Cartridge Section 1. Pulling the green knob until stopping (①), at the same time rotating right (②) and pulling it completely. A2-10 © 2016 Nautilus Hyosung Inc. All Rights Reserved.
  • Page 40 (Before mounting it, see the ink cartridge installation guide on the packing bag) 4. Push the green knob completely to the left arrow direction (⑤) to sound the click of the latch, and then it is locked automatically. A2-11 © 2016 Nautilus Hyosung Inc. All Rights Reserved.

  • Page 41: Setting The Casters For Cash & Check In Module

    2. Unfasten 4 screws in the caster and adjust it to be 5.0mm [0.20inch] above the ground. 3. The distance between the caster and the floor may be different depending on the type of floor. (carpet, hardwood, cement, etc.) A2-12 © 2016 Nautilus Hyosung Inc. All Rights Reserved.

  • Page 42: Notes

    Installation Manual Notes Notes Notes-1 © 2016 Nautilus Hyosung Inc. All Rights Reserved.

Table of Contents