Advertisement
MT
RFID Installation Instructions
™
All parts needed to install the MT™ RFID lock are included with each unit. Please check to make
sure all parts are accounted for before beginning installation. Do not substitute any of the parts.
The use of substitute parts will result in poor performance of the lock.
Optional
Communication
Modules
I/S Escutcheon
All information contained herein, including but not limited to product pricing and other intellectual property, is confidential and
intended for the sole use of the addressee(s) so named. Any misuse of this confidential information contained herein may result in
legal action by Computerized Security Systems dba SAFLOK and its parent company.
A23390
(optional gasket for exterior use)
Mortise (see Mortise Options table)
51190-Color — Outside Front
I/S Chassis Assembly
A29030-Color — Screw Pack,
MT Universal 1-3/4 — 2-1/4
A21290-X-X-Color — O/S Housing Assy, MT RFID w/USB
30320-H-Color — Assy, Strike, Buttons
Mortise Options
A70000-Handing
Mortise, 1-3/4
A70020-Handing
Mortsie, 1-3/4
ADB
A70080-Handing
Mortise, 1-3/4
ADB, DAJ2
A70060-Handing
Mortise, 1-3/4
STD, DAJ2
Advertisement
Table of Contents
Related Manuals for Kaba Saflok MT RFID
Summary of Contents for Kaba Saflok MT RFID
- Page 1 RFID Installation Instructions ™ All parts needed to install the MT™ RFID lock are included with each unit. Please check to make sure all parts are accounted for before beginning installation. Do not substitute any of the parts. The use of substitute parts will result in poor performance of the lock. A21290-X-X-Color —...
- Page 2 RFID Installation Instructions Pg 2 of 8 Preparing the door and door frame Prepare the door using the MT RFID installation template or drill fixture. The door edge prep is a standard, full-mortise prep for a 1-1/4” x 8” front plate (1” x 8” and 1” x 7-3/4” custom front plates are optional). The door surface holes and mortise are customized for the SAFLOK trim.
- Page 3 RFID Installation Instructions Pg 3 of 8 Preparing the door and door frame (continued) 3. The mortise plate has an adjustable bevel. Align the mortise front plate with the bevel of the door edge and tighten the two bevel adjustment screws at the top and bottom of the mortise case. Position the mortise case in the door edge with the motor wire routed through the notch (see Fig.
- Page 4 RFID Installation Instructions Pg 4 of 8 Installing the lock trim Both the outside and inside trim assemblies have 1/4˝ alignment pins that fit into holes in the mortise case. These pins establish an accurate trim position with respect to the mortise case assembly, allowing the levers and bolt mechanism to operate freely without binding.
- Page 5 RFID Installation Instructions Pg 5 of 8 Installing the lock trim (continued) 9. Connect ribbon cable, motor wire, and reader power wire to the PCB. See Fig. 4. 10. Watch for the green LED on the card reader to flash four times while you connect the battery wire to the PCB. The green light indicates that the PCB has reset.
- Page 6 RFID Installation Instructions Pg 6 of 8 Installing the lock trim (continued) 13. Secure the inside trim cover to the inside trim using two M4 x 16mm Torx screws (see Fig. 5). Fig. 5 M4 x 16mm Torx 14. Program the lock using the Lock Programmer and Interrogator (LPI) probe (p# 72400) with the Hand Held Terminal. *The programming port is located in the bottom of the outside lock trim.
- Page 7 RFID Installation Instructions Pg 7 of 8 Testing Lock Functionality Pass a Construction key over the Quantum RFID reader. The green light will flash for five seconds. Be sure that the green light flashes for five seconds while the exterior lever remains operable. If the green light does not flash, refer to the table below.
- Page 8 RFID Installation Instructions Pg 8 of 8 SAFLOK Door Unit Inspection Criteria Appearance • Finish is free of blemishes or scratches that would distract from lock appearance • Lock body and under plate (if used) are mounted straight on the door • Door scalp is mounted straight and flush with the door edge • Jamb strike is mounted straight and is flush with the jamb face • Correction of minor blemishes on the door jamb are the responsibility of the property’s maintenance department Lock Function • Knob or lever rotates and moves freely • Lever is horizontal to floor when at rest position • Dead bolt extends fully and retracts without binding (door open) • Lock latch and dead bolt engage jamb strike plate freely • Anti-pick latch when depressed (door open) • Anti-pick latch is depressed when contact is made with the strike plate (door closed) Electronics/Keycards • Green light flashes when the proper keycard is used •...