Subscribe to Our Youtube Channel
Related Manuals for Teknik Barrister Home 5418902
Summary of Contents for Teknik Barrister Home 5418902
- Page 1 Teknik www.teknikoffice.co.uk Yes, you still have to dress yourself. Barrister Home Dresser Barrister Home Collection | Model 5418902 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
- Page 2 Table of Contents Assembly Tools Required Part Identifi cation No. 2 Phillips Screwdriver Tip Shown Actual Size Hardware Identifi cation Assembly Steps 5-22 Hammer Not actual size Skip the power trip. This time. Page 2...
- Page 3 Now you know Part Identifi cation our ABCs. å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identifi cation to help identify similar parts. RIGHT END (1) LEFT BASE (1) D22 DRAWER RIGHT SIDE (4)
- Page 4 Hardware Identifi cation å Screws are shown actual size. You may receive extra hardware with your unit. 10A SLIDE CAM - 12 35AA UNIVERSAL CABINET RAIL - 12 35AC DRAWER RIGHT - 6 35AD DRAWER LEFT - 6 MOLDING SAFETY METAL HIDDEN CAM DOWEL - 16...
- Page 5 Step 1 Assemble your unit on a carpeted fl oor or on the empty å carton to avoid scratching your unit or the fl oor. Push sixteen HIDDEN CAMS (1F) into the ENDS (A and B), å UPRIGHT (C), BOTTOM (E), and DRAWER BRACES (M64). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM.
- Page 6 Step 2 Fasten six UNIVERSAL CABINET RAILS* (35AA) to the å ENDS (A and B). Use twelve GOLD 5/16" FLAT HEAD Remember: SCREWS (3S) through holes #1 and #3. Righty tighty. Lefty loosey. *patent pending glide system å GOLD 5/16" FLAT HEAD SCREW (12 used in this step) Glide end Finished edge...
- Page 7 Step 3 Fasten six UNIVERSAL CABINET RAILS* (35AA) to å the UPRIGHT (C). Use twelve GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. *patent pending glide system å GOLD 5/16" FLAT HEAD SCREW (12 used in this step) Glide end Edge with CAM DOWELS...
- Page 8 Step 4 Fasten the TOP (D) to the RAILS (Q and R). Use eight å BLACK 1-7/8" FLAT HEAD SCREWS (2S). Curved edge BLACK 1-7/8" FLAT HEAD SCREW (8 used in this step) Page 8...
- Page 9 Step 5 Tap two MOLDING CONNECTORS (19F) into the notches å in the MOLDINGS (M, N, and O). Use your hammer to tap the MOLDING CONNECTORS (19F) into the notches in the MOLDINGS. Flat end Flat end Unfi nished surface Unfi...
- Page 10 Step 6 Fasten the TOP (D) to the MOLDINGS (M, N, and O). Use å eight SILVER 1-1/8" FLAT HEAD SCREWS (10S). NOTE: Do not overtighten the SCREWS into the TOP. å SILVER 1-1/8" FLAT HEAD SCREW (8 used in this step) Do not overtighten the SCREWS (10S).
- Page 11 Step 7 Fasten the UPRIGHT (C) to the BOTTOM (E). Use two å Caution BLACK 1-7/8" FLAT HEAD SCREWS (2S). Do not stand the unit upright without the BACK fastened. The unit may collapse. Finished edge These holes must be here. S u r f a c w i t h...
- Page 12 Step 8 Insert eight METAL PINS (1R) into the holes in the ENDS (A å and B) and UPRIGHT (C). Place the BRACES (G) onto the METAL PINS in the UPRIGHT (C). å Fasten the ENDS (A and B) to the BOTTOM (E). Tighten four å...
- Page 13 Step 9 Fasten the TOP (D) to the UPRIGHT (C). Tighten two å HIDDEN CAMS. Maximum Arrow 210 degrees Fasten the MOLDINGS (N and O) to the ENDS (A and B). å Tighten four HIDDEN CAMS. Minimum 190 degrees Page 13...
- Page 14 Step 10 Fasten the BASES (I and J) to the ENDS (A and B). Use å four BLACK 1-1/4" FLAT HEAD SCREWS (7S). BLACK 1-1/4" FLAT HEAD SCREW (4 used in this step) Flat edge Flat edge Page 14...
- Page 15 Step 11 Fasten eight METAL BRACKETS (4G) to the ENDS (A å and B) and BOTTOM (E). Use eight BLACK 9/16" LARGE HEAD SCREWS (1S). NOTE: Be sure the edges of the METAL BRACKETS are even å with the edges of the ENDS and BOTTOM. Fasten the BASE (H) to the ENDS (A and B) and BOTTOM (E).
- Page 16 Step 12 Carefully turn your unit over onto its front edges. Unfold å Caution the BACK (F) and lay it over your unit. Do not stand the unit upright without the Make equal margins along all four edges of the BACK (F). å...
- Page 17 Step 13 With the palm of your hand, The tabs should insert freely tap the DRAWER BOTTOM into the slots. Gently tilt the down into the groove. DRAWER SIDES side to side until the tabs slip into the slots. fi n i s h r f a D977...
- Page 18 Step 14 Insert a SLIDE CAM (10A) into the DRAWER SIDES (D22 and D23). å Fasten a DRAWER RIGHT (35AC) to the DRAWER RIGHT SIDE (D22) å and a DRAWER LEFT (35AD) to the DRAWER LEFT SIDE (D23). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #2. NOTE: The screw head in the CAM must be visible through the slotted å...
- Page 19 Step 15 Fasten four KNOBS (71K) to the UPPER DRAWER FRONT (K). å Use four BLACK 7/8" MACHINE SCREWS (37S). Fasten two PULLS (70K) to the DRAWER FRONT (L). Use four å BLACK 7/8" MACHINE SCREWS (37S). Repeat this step for the remaining drawers. å...
- Page 20 Step 16 Carefully stand your unit upright. å We recommend using the SAFETY BRACKET (1G) å for added stability. Use a BLACK 9/16" LARGE HEAD SCREW (1S) into the underneath surface of the TOP (D) and a BLACK 1-7/8" FLAT HEAD SCREW (2S) into a stud in your wall.
- Page 21 Step 17 To insert the drawer into your unit, tip the front of the drawer down and drop the glides on the drawer behind the glides å on the unit. Lift the front of the drawer up and slide it into the unit. Apply the WARNING LABEL (5L) to the SMALL DRAWER LEFT SIDE (D27).
- Page 22 Step 18 To make adjustments to the drawers, loosen SCREW #2 in the SLIDES a 1/4 turn, then turn the CAM clockwise or å counter-clockwise. Notice how the drawer raises or lowers as you turn the CAM. The higher the screw in the oblong hole, the higher your drawer front will be.
- Page 23 WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded dresser drawers and •...
Need help?
Do you have a question about the Barrister Home 5418902 and is the answer not in the manual?
Questions and answers