Related Manuals for WAGO I/O-SYSTEM 750-478
Summary of Contents for WAGO I/O-SYSTEM 750-478
- Page 1 Fieldbus Independent I/O Modules 2 AI DC 0-10 V, Single-Ended 750-478 Manual Version 1.0.2...
- Page 2 • General Copyright © 2006 by WAGO Kontakttechnik GmbH & Co. KG All rights reserved. WAGO Kontakttechnik GmbH & Co. KG Hansastraße 27 D-32423 Minden Phone: +49 (0) 571/8 87 – 0 Fax: +49 (0) 571/8 87 – 1 69 E-Mail: info@wago.com...
-
Page 3: Table Of Contents
750-478 [2 AI DC 0-10 V, Single-Ended]........... 7 2.1.1.1 View....................7 2.1.1.2 Description..................7 2.1.1.3 Display Elements ................8 2.1.1.4 Schematic Diagram................. 9 2.1.1.5 Technical Data ................9 2.1.1.6 Process Image ................11 2.1.1.6.1 Standard Data Format .............. 12 WAGO-I/O-SYSTEM 750 I/O Modules... -
Page 4: Important Comments
WAGO Kontakttechnik GmbH & Co. KG declines all liability resulting from improper action and damage to WAGO products and third party products due to non-observance of the information contained in this manual. -
Page 5: Symbols
Routines or advice for efficient use of the device and software optimization. More information References on additional literature, manuals, data sheets and INTERNET pages 1.3 Number Notation Number Code Example Note Decimal normal notation Hexadecimal 0x64 C notation Binary '100' Within ', '0110.0100' Nibble separated with dots WAGO-I/O-SYSTEM 750 I/O Modules... -
Page 6: Safety Notes
Do not use any contact spray. The spray may impair the functioning of the contact area. The WAGO-I/O-SYSTEM 750 and its components are an open system. It must only be assembled in housings, cabinets or in electrical operation rooms. Access must only be given via a key or tool to authorized qualified personnel. -
Page 7: O Modules
Any configuration of the input modules is possible when designing the fieldbus node. Grouping of module types is not necessary. The field side supply voltage of 24 V and 0 V for the input module is derived from adjacent I/O modules or from a supply module. WAGO-I/O-SYSTEM 750 I/O Modules... -
Page 8: Display Elements
However, if such a case should occur, another supply module must be added. The analog input module 750-478 can be used with all couplers/controllers of the WAGO-I/O-SYSTEM 750 (except for the economy types 750-320, -323, -324 and -327). 2.1.1.3... -
Page 9: Schematic Diagram
– at sampling frequency < -100 dB – above sampling frequency < -40 dB Dimensions (mm) W x H x L 12 x 64* x 100 * from upper edge of 35 DIN rail Weight ca. 55 g WAGO-I/O-SYSTEM 750 I/O Modules... - Page 10 II 3 GD EEx nA II T4 Conformity Marking More Information Detailed references to the approvals are listed in the document "Overview Approvals WAGO-I/O-SYSTEM 750", which you can find on the CD ROM ELECTRONICC Tools and Docs (Item-No.: 0888-0412) or in the internet under: www.wago.com...
-
Page 11: Process Image
Some fieldbus systems can process input channel status information by means of a status byte. This status byte can be displayed via the starting tool WAGO-I/O-CHECK 2. However, processing via the coupler / controller is optional, which means that accessing or parsing the status information depends on the fieldbus system. -
Page 12: Standard Data Format
0x00 5.00 '0100.0000.0000.0000' 0x4000 16384 0x00 6.25 '0101.0000.0000.0000' 0x5000 20480 0x00 7.50 '0110.0000.0000.0000' 0x6000 24576 0x00 8.75 '0111.0000.0000.0000' 0x7000 28672 0x00 10.00 '0111.1111.1111.1111' 0x7FFF 32767 0x00 >10.50 '0111.1111.1111.1111' 0x7FFF 32767 0x42 >11.00 '0111.1111.1111.1111' 0x7FFF 32767 0x42 WAGO-I/O-SYSTEM 750 I/O Modules... - Page 13 750-478 [2 AI DC 0-10 V, Single-Ended] • 13 Process Image WAGO-I/O-SYSTEM 750 I/O Modules...
- Page 14 WAGO Kontakttechnik GmbH & Co. KG Postfach 2880 • D-32385 Minden Hansastraße 27 • D-32423 Minden Phone: 05 71/8 87 – 0 Fax: 05 71/8 87 – 1 69 E-Mail: info@wago.com Internet: http://www.wago.com...