Stripping and crimping machine Crimpfix 2.5 M Inhaltsverzeichnis 1. Terms of use ..........................3 2. Prescribed use ..........................3 3. Safety and the environment......................4 General ................................. 4 Safety instructions ............................4 Safety precautions ............................4 Setup................................4 Symbols and indications ..........................5 Training of personnel ............................
Please read carefully through this manual and observe the notes and explanations. Only by carefully following these instructions the proper and trouble free operation of the Crimpfix 2.5 M machine can be guaranteed. These operating instructions have been written with due care and attention. However, unless otherwise required by law, we do not guarantee that the data, images and drawings are accurate or complete nor do we accept liability for their contents.
This manual contains important safety directions. All people working at the machine have to observe them. Safety instructions Depending on the model, the Crimpfix 2.5 M is configured with a power supply for AC voltage of either115 V or 240 V.
Stripping and crimping machine Crimpfix 2.5 M Symbols and indications Before switching on the machine, read through the operating manual carefully. Use the machine only at dry places. Caution! This symbol indicates a possible hazardous situation. Failure to observe these warnings could result in moderate injuries or property damages.
Stripping and crimping machine Crimpfix 2.5 M Technical specifications Drive..........................Electric motor Power supply ......................1~230 V / 50 Hz Power consumption ........................100 VA Fuse (line filter) ......................2 x T2AH250V Protecting class..........................IP20 Cycle time ............................. 1.5 s Continuous sound level .......................< 70 dB(A)
Stripping and crimping machine Crimpfix 2.5 M General view of the machine Reel holder Fixing screw of the reel holder Flap Cross-section range Switch from 0.5-2.5 to 0.34 Display Feeding funnel Keypad Stripping-waste container Figure 1: Front view Reel holder...
Stripping and crimping machine Crimpfix 2.5 M Operating instructions Putting into operation • Put in the stripping-waste container. Take care that the container is completely inserted. • Connect the mains cable to the machine and to the electrical supply. (The data on the type plate must agree with the mains supply.)
Stripping and crimping machine Crimpfix 2.5 M Changing the ferrule belt • Open the flap. • Release the locking pin (see Figure 3) and remove the magazine. • Push the transport pin completely up and take out the ferrule belt.
Stripping and crimping machine Crimpfix 2.5 M Wire feeding - Wire section • The wire has to be cut off straight and may not have any bends or bows. • Insert the wire into the feeding funnel until the working cycle is triggered.
Stripping and crimping machine Crimpfix 2.5 M Main menu P-No Cross-section Operating menu Ready S: Piece counter Daily piece counter 5s Delete daily piece counter Software-Version / Type Program Current P-No:Cross-section Program P-No Cross-section 1 : 0.34 mm² (D=0.70mm) : 0.50 mm² (D=0.90mm) Guide value : 0.75 mm²...
Stripping and crimping machine Crimpfix 2.5 M Special functions Display Contrast Mains switch + Edit Exit Adjusting Stripping Depth Remove the magazine Close the flap S-Motor Press it 5 seconds till cursor Cutting edge of the stripping blades starts blinking...
Stripping and crimping machine Crimpfix 2.5 M 10.3 Striping blades changing position Shaft Groove – driving lever Right screw, red marked Protection plate Left screw, red marked Magazine holder Stripping slide S-Motor Table guidance Fixing screw – attachment Figure 8: Striping blades changing position →...
Stripping and crimping machine Crimpfix 2.5 M Trouble shooting See chapter 3.8. Using risks Trouble Elimination Double crimp See Jammed wire Jammed wire Remove the Magazine. If there is a ferrule in the crimping tool, take it away. Remove the feeding funnel.
Page 16
Stripping and crimping machine Crimpfix 2.5 M Display is not readable Contrast setup is not ok. Mains switch + Edit Exit Key presses are not accepted Keyboard is damaged Keyboard check Main switch and Back to main menu Ferrule misses on the stripped wire Open the flap and remove the magazine.
Stripping and crimping machine Crimpfix 2.5 M 11.1 Error messages The error messages are shown on the display. The error messages are deleted by pressing key Code Fault Elimination Flashe. Saving or loading error Turn machine off and on or call the service.
Stripping and crimping machine Crimpfix 2.5 M Declaration of conformity The firm Weidmüller Interface GmbH & Co. Klingenbergstraße 16 D-32758 Detmold attests, in sole-responsibility, that the product Stripping and crimping machine Crimpfix 2.5 M Fabrication number: which this declaration refers to, agrees with the following standards and guidelines:...