Table of Contents
Advertisement
Unmanaged Fast Ethernet PoE
Switches Basic Line
IE-SW-BL06-4PoE Series
Hardware Installation Guide
Fifth Edition, March 2014
1254030000/04/03.14
Important note:
This document and additional product information can be
downloaded using following link:
http://www.weidmueller.com
► Select Product Catalogue
Select „Industrial Ethernet active"
Select „PoE unmanaged Switches"
Select Product model
Click and expand section „Downloads"
Download needed documentation
Copyright Notice
Copyright
2014 Weidmüller Interface GmbH & Co. KG
All rights reserved.
Reproduction without permission is prohibited.
Advertisement
Table of Contents
Related Manuals for Weidmuller IE-SW-BL06-4PoE Series
Summary of Contents for Weidmuller IE-SW-BL06-4PoE Series
- Page 1 Unmanaged Fast Ethernet PoE Switches Basic Line IE-SW-BL06-4PoE Series Hardware Installation Guide Fifth Edition, March 2014 1254030000/04/03.14 Important note: This document and additional product information can be downloaded using following link: http://www.weidmueller.com ► Select Product Catalogue Select „Industrial Ethernet active“...
-
Page 2: Package Checklist
Overview The IE-SW-BL06-4PoE series industrial Ethernet switches are entry- level industrial 6-port PoE Ethernet switches that supports IEEE 802.3, IEEE 802.3u, and IEEE 802.3x, with 10/100M, full/half-duplex, MDI/MDIX auto-sensing, IEEE 802.3af (PoE) and IEEE 802.3at (PoE+). The PoE switch family provides 24/48 VDC redundant power inputs that can be connected simultaneously to a live DC power source. - Page 3 Panel Layout of IE-SW-BL06(T)-2TX-4PoE Grounding screw Terminal block for power input P1/P2 Heat dissipation orifices DIP switches Power input P1 LED Power input P2 LED PoE LED 10/100BaseT(X) port TP port’s 10/100 Mbps 10. Article Number 11. Screw hole for wall mounting kit 12.
- Page 4 Panel Layout of IE-SW-BL06(T)-1TX-4PoE-1SC and IE-SW-BL06(T)-1TX-4PoE-1ST IE-SW-BL06(T)-1TX-4PoE-1SC IE-SW-BL06(T)-1TX-4PoE-1ST Front Panel View Front Panel View Grounding screw Terminal block for power input P1/P2 Heat dissipation orifices DIP switches Power input P1 LED Power input P2 LED PoE LED 10/100BaseT(X) port TP port’s 10/100 Mbps 10.
- Page 5 Panel Layout of IE-SW-BL06(T)-4PoE-2SC and IE-SW-BL06(T)-4PoE-2ST IE-SW-BL06(T)-4PoE-2SC IE-SW-BL06(T)-4PoE-2ST Front Panel View Front Panel View Grounding screw Terminal block for power input P1/P2 Heat dissipation orifices DIP switches Power input P1 LED Power input P2 LED PoE LED 10/100BaseT(X) port TP port’s 10/100 Mbps 10.
-
Page 6: Mounting Dimensions (Unit = Mm)
Mounting Dimensions (unit = mm) DIN-Rail Mounting The aluminum DIN-Rail attachment plate should already be fixed to the back panel of the Ethernet Switch when you take it out of the box. If you need to reattach the DIN-Rail attachment plate, make sure the stiff metal spring is situated towards the top, as shown in the figures below. -
Page 7: Wall Mounting (Optional)
Wall Mounting (optional) For some applications, you will find it convenient to mount the IE-SW- BL06-4PoE switch on the wall, as shown in the following figures. STEP 1: Remove the aluminum DIN-Rail attachment plate from the switch rear panel, and then attach the wall mount plates as shown in the diagram at the right. -
Page 8: Wiring Requirements
Wiring Requirements WARNING Safety First! Turn the power off before disconnecting modules or wires. The correct power supply voltage is listed on the product label. Check the voltage of your power source to make sure that you are using the correct voltage. Do NOT use a voltage greater than what is specified on the product label. -
Page 9: Wiring The Redundant Power Inputs
Wiring the Redundant Power Inputs The top two contacts and the bottom two contacts of the 4-contact terminal block connector on the top panel are used for the Ethernet Switch´s two DC inputs. Top and front views of one of the terminal block connectors are shown here. - Page 10 PoE 10/100BaseT(X) Ethernet Port Connection PoE 10/100BaseT(X) ports located on the switch’s front panel are used to connect to PoE-enabled devices. The pinout follows the “Alternative A, MDI-X mode” of 802.3af/at standards. Please see the details in the following table. PoE Port Pinout 8-pin RJ45 Data...
-
Page 11: 100Basefx Ethernet Port Connection
100BaseFX Ethernet Port Connection The concept behind the SC/ST port and cable is quite straightforward. Suppose you are connecting devices I and II; contrary to electrical signals, optical signals do not require a circuit in order to transmit data. Consequently, one of the optical lines is used to transmit data from device I to device II, and the other optical line is used transmit data from device II to device I, for full-duplex transmission. -
Page 12: Led Indicators
ATTENTION To actively update DIP switch settings, power off and then power on the Ethernet Switch. LED Indicators The front panel of the Ethernet Switch contains several LED indicators. The function of each LED is described in the following table. Color State Description... -
Page 13: Dual Speed Functionality And Switching
Dual Speed Functionality and Switching The Ethernet Switch 10/100 Mbps switched RJ45 port auto negotiates with the connected device for the fastest data transmission rate supported by both devices. All models of Weidmüller Ethernet Switch are plug-and-play devices, so that software configuration is not required at installation, or during maintenance. -
Page 14: Specifications
Specifications Technology Standards IEEE 802.3 for 10BaseT IEEE 802.3u for 100BaseT(X) and 100BaseFX IEEE 802.3x for Flow Control IEEE 802.3af for PoE IEEE 802.3at for PoE+ Processing Type Store and Forward Flow Control IEEE 802.3x flow control, back pressure flow control Interface RJ45 Ports... - Page 15 Physical Characteristics Housing Metal, IP30 protection Dimensions 50 x 115 x 70 mm (W x H x D) Weight 275 g Installation DIN-Rail Mounting, Wall Mounting (with optional kit) Environmental Limits Operating Standard models: 0 to 60°C (32 to 140°F) Temperature Wide temp.
- Page 16 Weidmüller gives a 5 year warranty on this product in accordance with the warranty terms as described in the general conditions of sale of the Weidmüller company which has sold the products to you. Weidmüller warrants to you that such products the defects of which have already existed at the time when the risk passed will be repaired by Weidmüller free of charge or that Weidmüller will provide a new, functionally equivalent product to replace the defective one.