Table of Contents
Advertisement
Gigabit Ethernet Switch – Value Line
IE-SW-VL08-GT Series
Hardware Installation Guide
Third Edition, October 2012
1243390000/02/10.12
Please note:
This document and any further product information - if
available - can be downloaded at the internet link:
http://www.weidmueller.com/downloads
Copyright Notice
Copyright
2012 Weidmüller Interface GmbH & Co. KG
All rights reserved.
Reproduction without permission is prohibited.
Advertisement
Table of Contents
Related Manuals for Weidmuller IE-SW-VL08-8GT
Summary of Contents for Weidmuller IE-SW-VL08-8GT
-
Page 1: Hardware Installation Guide
Gigabit Ethernet Switch – Value Line IE-SW-VL08-GT Series Hardware Installation Guide Third Edition, October 2012 1243390000/02/10.12 Please note: This document and any further product information - if available - can be downloaded at the internet link: http://www.weidmueller.com/downloads Copyright Notice Copyright 2012 Weidmüller Interface GmbH &... -
Page 2: Package Checklist
Overview The IE-SW-VL08-GT series is equipped with 8 Gigabit Ethernet ports and up to 2 fiber optic ports, making it ideal for applications that demand high bandwidth. These Switch Models provide an economical solution for your industrial Gigabit Ethernet connection, and the built-in relay warning function alerts maintainers when power failures or port breaks occur. - Page 3 Panel Layout of IE-SW-VL08-GT Series IE-SW-VL08-8GT IE-SW-VL08-6GT-2GS Front Panel View Front Panel View 1. Grounding screw 2. Terminal block for power input (PWR1, PWR2) and relay output 3. Power input PWR1 LED 4. Power input PWR2 LED 5. Fault LED 6.
-
Page 4: Mounting Dimensions (Unit = Mm)
Mounting Dimensions (unit = mm) DIN-Rail Mounting The aluminum DIN-rail attachment plate should already be fixed to the back panel of the Ethernet Switch when you take it out of the box. If you need to reattach the DIN-rail attachment plate, make sure the stiff metal spring is situated towards the top, as shown in the figures below. -
Page 5: Atex Information
Maximum 0.65 A; resistive load 18-30 V AC, Class 2, 50/60 Hz, Maximum 0.5 A IE-SW-VL08-8GT-2GS 12-48 V DC, Class 2, Maximum 0.71 A; 18-30 V AC, Class 2, 50/60 Hz, Maximum 0.55 A 6. The conditions of safe usage: These products must be mounted in an IP54 enclosure. -
Page 6: Wiring The Alarm Contact
You should also pay attention to the following items: Use separate paths to route wiring for power and devices. If power wiring and device wiring paths must cross, make sure the wires are perpendicular at the intersection point. NOTE: Do not run signal or communications wiring and power wiring in the same wire conduit. -
Page 7: Wiring The Redundant Power Inputs
Wiring the Redundant Power Inputs The top two contacts and the bottom two contacts of the 6-contact terminal block connector on the Ethernet Switch’s top panel are used for the Ethernet Switch’s two AC/ DC inputs. Top and front views of one of the terminal block connectors are shown here. - Page 8 1000BaseT RJ45 Pinouts MDI-X BI_DA+ BI_DB+ BI_DA- BI_DB- BI_DB+ BI_DA+ BI_DC+ BI_DD+ BI_DC- BI_DD- BI_DB- BI_DA- BI_DD+ BI_DC+ BI_DD- BI_DC- RJ45 (8-pin) to RJ45 (8-pin) Straight-Through Cable Wiring RJ45 (8-pin) to RJ45 (8-pin) Cross-Over Cable Wiring 100Base-FX or 1000Base-X Fiber Port The Fiber ports on the IE-SW-VL08-6GT-2GS are SFP type slots, which support both 100Base-FX and 1000Base-X speed fiber transceiver to work properly.
-
Page 9: Redundant Power Inputs
0 to 550 m, 1310 nm (62.5/125μm, 500MHz*km) Single-mode: 1000BaseLX 0 to 10 km, 1310 nm (9/125μm, 3.5 PS/(nm*km)) 1000BaseLHX 0 to 40 km, 1310 nm (9/125μm, 3.5 PS/(nm*km)) Multi-mode: 100BaseFx 0 to 5 km, 1300 nm (50/125μm, 800MHz*km) 0 to 4 km, 1300 nm (62.5/125μm, 500MHz*km) Single-mode: 100BaseFx 0 to 40 km, 1310 nm (9/125μm, 3.5 PS/(nm*km)) -
Page 10: Dip Switch Settings
If neither of these two conditions occurs, the Fault circuit will be closed. DIP Switch Settings The default setting for each DIP switch is OFF. The following table explains the effect of setting the DIP switches to the ON positions. DIP Switch Setting Description... -
Page 11: Auto Mdi/Mdi-X Connection
When the corresponding PORT alarm is enabled and the port’s link is active, or when the corresponding PORT alarm is disabled. TP port’s 10/100 Mbps link is active Blinking Data is being transmitted at 10/100 Mbps 10/100M AMBER TP Port’s 10/100 Mbps link is inactive TP port’s 1000 Mbps link is active Blinking Data is being transmitted at 1000 Mbps GREEN... -
Page 12: Specifications
Specifications Specifications and Pin Assignments Technology IEEE 802.3 for 10BaseT, Standards IEEE 802.3u for 100BaseT(X) and 100Base FX, IEEE 802.3ab for 1000BaseT, IEEE 802.3z for 1000BaseSX/LX/LHX/ZX Flow Control IEEE 802.3x flow control, back pressure flow control Interface RJ45 Ports 10/100/1000BaseT(X) auto negotiation speed Fiber Ports 100Base-FX or 1000Base-X SFP slot LED Indicators... - Page 13 Input Voltage 12/24/48 VDC (9.6 to 60 VDC), 18 to 30VAC (47 to 63 Hz), redundant dual inputs Input Current @ 24VDC 0.35A Connection One removable 6-pin terminal block Overload Current Present Protection Reverse Polarity Present Protection Mechanical Casing IP30 protection, metal case Dimension (W x H x D) 53.6 x 135 x 105 mm (2.11 x 5.31 x 4.13 in) Weight 850g...
-
Page 14: Contact Information
5 years WARRANTY Weidmüller gives a 5 year warranty on this product in accordance with the warranty terms as described in the general conditions of sale of the Weidmüller company which has sold the products to you. Weidmüller warrants to you that such products the defects of which have already existed at the time when the risk passed will be repaired by Weidmüller free of charge or that Weidmüller will provide a new, functionally equivalent product to replace the defective one.