Table of Contents
Advertisement
Safety Information
Stored Energy Hazard
Even when the machine is not operating, energy
can be stored in components such as hydraulic
accumulators, air tanks, tyres, hoses, springs and boom
cables. Hydraulically supported components such as
the boom center are also a source of stored energy.
Before working on the machine, ensure that these
parts are relieved of their energy in a safe manner.
Overhead Hazard
BOOM LIFT OR TILT COULD STRIKE POWER
LINES. Keep clear of overhead obstructions –
especially power lines as contact can be fatal.
Do NOT walk on machine platform when near
power lines.
Airborne Particles
• Always stand well clear of equipment during
operation.
• Any spray drift is dangerous and may be hazardous
to humans and other animals.
• When heating and welding components, ensure
that all paint and other such materials are removed.
Often hazardous airborne particles and fumes are
generated from welding and heating.
Fluids Under Pressure
Fluids escaping from high pressure lines can cause
serious injury to skin. Hydraulic oil can easily penetrate
human skin. This hazard can be avoided by relieving
the pressure in the system.
Do not disconnect any hoses, nozzles or filters
while equipment is operating. Disconnecting these
components while under pressure may result in
uncontrolled fluid discharge which may be hazardous.
Be mindful of the location of pressurised lines in the
vicinity of the work area when using equipment such
as grinders, oxy torches and welders. The two main
risks are that this equipment may easily cut through
the lines or the local heat generated near the lines
may cause them to rupture.
Ensure that all fittings and lines are fully/tightly secured
before re-pressurizing after repairs.
Norac System
If Norac height control system is fitted, keep clear of
the boom as it could potentially move without notice.
Lifting Machine
Before raising the machine off the ground:
Ensure that the boom is in its closed position.
Park up on a flat, level and firm area.
Prairie Compact 2000L Operator's Manual MY19 - REV 1
Empty the spray tank where possible.
Chock all wheels that remain on the ground.
Securely lift the machine using a jack and support
the machine on work stands.
Do not work under the machine when supported
solely by a jack.
Do not support the sprayer using materials that
may crumble.
Changing Wheels & Tyres
An experienced person with the correct equipment
should mount the wheels on the sprayer.
When changing a wheel on the sprayer ensure that
the sprayer is on firm level ground and the wheels are
chocked.
Tyre Maintenance
Maintain correct tyre pressure at all times. Inflation
of tyres above or below the recommended pressure
exerts additional pressure on the tyre, which may
result in tyre damage.
Extreme caution is required during the inflation of
tyres. If the tyre is inflated at a rapid rate separation
and/or explosion of the rim can occur. This event can
inflict serious or fatal injuries to the operator.
Always use a tyre inflation gauge.
Be proactive and continually check the condition of
your tyres.
Do not weld, heat or modify the rim.
Machine Operation
• High speed turning places severe stresses on
the wheels and axles and should be avoided. It
is essential to observe the effects of turning on
the open spray boom. Excessive turning speeds
transmit great stresses to the spray boom and
WILL CAUSE boom damage.
• This machine is designed for a maximum speed of
50 km/h. This speed must only be used on suitable
terrain conditions. All components i.e. tyres, brakes,
suspension, steering and chassis are designed and
built to this maximum speed.
• MAXIMUM SPEED WHEN CORNERING,
TURNING AT AN ANGLE GREATER THAN
45º OR DRIVING ON A SLOPE OR UNEVEN
TERRAIN IS 5KM/H. When fitted with narrow
wheel track and with high centre of gravity, the
sprayer may become unstable when turning at
excessive speed or when operating on excessively
steep terrain.
Continued over page
Chapter 2 - Safety - 5
Advertisement
Table of Contents
