Table of Contents
Related Manuals for NSK ENDO-MATE TC2
Summary of Contents for NSK ENDO-MATE TC2
- Page 1 Cordless Handpiece OPERATION MANUAL Please read this Operation Manual carefully before use, and file for future reference. The EU directive 93/42/EEC was applied in the design and production of this medical device. OM-E0390E 001 2013.02.20 02...
- Page 2 English Cordless Handpiece OPERATION MANUAL...
- Page 3 Guidance and manufacturer's declaration - electromagnetic emissions The ENDO-MATE TC2 is intended for use in the electromagnetic environment specified below. The customer or the user of the ENDO-MATE TC2 should assure that is used in such an environment. Emissions test...
- Page 4 The ENDO-MATE TC2 is intended for use in the electromagnetic environment specified below. The customer or the user of the ENDO-MATE TC2 should assure that it is used in such an environment. customer or the user of the ENDO-MATE TC2 should assure that it is used in such an environment.
-
Page 5: Table Of Contents
ENDO-MATE TC2 CONTENTS The ENDO-MATE TC2 is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of the ENDO-MATE TC2 can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF... - Page 6 • Be careful not to drop conductive parts such as wires and safety pins into the charging terminal area of the battery charger. • To charge the motor handpiece, only use a dedicated genuine NSK charger. Never charge this handpiece with a charger other than the genuine NSK charger.
-
Page 7: Features
NOTICE • The motor handpiece can be turned on and off by pressing the ON/OFF key. Alternatively the unit can be operated by holding down the ON/OFF key during operation and letting go of the • The motor handpiece is designed for commercially available AAA nickel metal hydride ON/OFF key to stop the handpiece. -
Page 8: Parts And Its Function
NOTICE 4. Parts and its function • If the speed or torque set value has reached the upper limit or lower limit when the <Operation Panel Details> gear ratio has been changed, the alarm sounds. <LCD Panel> • The indication of “ ”... -
Page 9: Operations
• BATTERY Symbol 5. Operations The symbol indicating the battery status is displayed. The symbol will be animated when the (1) Charging Batteries batteries are being charged or in the refresh mode. 1. Insert the power cord jack into the inlet at the back of the battery charger. (Fig. 1) : Full charge or nearly full charge 2. - Page 10 • Batteries may slightly warm up during charging, but this is not a failure. If the • Do not connect other than NSK F-type contra angle handpiece. handpiece is inserted or removed into/from the charger at short intervals, (approx. 5 (In the EU, use the CE-marked handpiece.)
- Page 11 (4) Preparatory Operations <Operation Panel> AUTO REVERSING 1. Hold down the POWER key for more than one second ON/OFF key to turn on the power. The handpiece stop that it reaches for the loaded value, the file rotates in reverse. When a load 2.
-
Page 12: Convenient Function
POWER key for more than one second to turn off the power. difference in torque by the contra angle head. 1. Lubricate the contra angle head with NSK PANA SPRAY/PANA SPRAY Plus (option). (Refer Auto Power Off to the “7 (1) Lubricating Contra Angle Head.”) If the key is not operated or approximately 10 minutes passes during rotation with no-load, the 2. -
Page 13: Cleaning
7. Cleaning 8. Sterilization (1) Lubricating Contra Angle Head Sterilize the contra angle head only. For the sterilization method, we recommend the autoclaving. Sterilization is required first time • Lubricate the contra angle head only. you use and after each patient as noted below. •... -
Page 14: Safety System
“ CAUTIONS ON CHANGING BATTERIES.” Please note that NSK shall not be liable operation of the handpiece. for any malfunction or failure resulting from you changing the batteries yourself and not 7. -
Page 15: Error Code
12. Error Code 13. Troubleshooting If the motor handpiece stops due to an abnormality such as a malfunction, overload, break or When trouble is found, please check the following again before consulting your dealer. If none wrong use, it automatically checks the state of the control unit and detects the cause of the of these is applicable or the trouble is not remedied even after action has been taken, a failure abnormality and displays an error code on the LCD panel. -
Page 16: Warranty
14. Warranty The motor If nothing is displayed on the liquid handpiece set crystal panel of the handpiece Manufacturer warrants its products to the original purchaser against defects in material and to the charger Contact your dealer. even when it is set to the charger, workmanship under normal practices of installation, use and servicing.