Subscribe to Our Youtube Channel
Related Manuals for ADLINK Technology DLAP-201 Series
Summary of Contents for ADLINK Technology DLAP-201 Series
- Page 1 DLAP-201 Series DLAP-201-JT2 / DLAP-201-JT2i Edge Inference System User’s Manual Manual Rev.: Revision Date: January 14, 2020 Part No: 50-1Z308-1000 Leading EDGE COMPUTING...
- Page 2 Leading EDGE COMPUTING Revision History Revision Release Date Description of Change(s) 2020-01-14 Initial Release...
- Page 3 DLAP-201 Series Preface Copyright © 2020 ADLINK Technology, Inc. This document contains proprietary information protected by copy- right. All rights are reserved. No part of this manual may be repro- duced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.
- Page 4 Leading EDGE COMPUTING Conventions Take note of the following conventions used throughout this manual to make sure that users perform certain tasks and instructions properly. Additional information, aids, and tips that help users perform tasks. NOTE: NOTE: Information to prevent minor physical injury, component dam- age, data loss, and/or program corruption when trying to com- plete a task.
-
Page 5: Table Of Contents
DLAP-201 Series Table of Contents Preface ..................iii List of Tables................. vii List of Figures ................ ix 1 Introduction ................ 1 Features................1 Specifications............... 2 Mechanical Dimensions............4 External Layout..............5 Pin Definitions..............7 1.5.1 Ethernet GbE Connectors .......... 7 1.5.2... - Page 6 Leading EDGE COMPUTING 2.9.1 COM Mode Switches ..........24 2.9.2 AT Mode Switch (SWS1501) ........24 2.9.3 GPIO Switch (CN1501)..........24 3 Using the System.............. 25 Software Configuration ............25 System Recovery............... 25 COM Port Configuration............. 26 Important Safety Instructions..........27 Getting Service ..............
-
Page 7: List Of Tables
DLAP-201 Series List of Tables Table 1-1: Specifications ............. 3 Table 1-2: Front Panel I/O Connectors & Controls ...... 5 Table 1-3: Rear Panel I/O Connectors ........6 Table 1-4: RJ-45 GbE Pin Definition..........7 Table 1-5: USB 3.0 Pin Definition ..........8 Table 1-6: 12 Volt DC Connector Pin Definition ...... - Page 8 Leading EDGE COMPUTING This page intentionally left blank. viii List of Tables...
-
Page 9: List Of Figures
DLAP-201 Series List of Figures Figure 1-1: Front View Dimensions..........4 Figure 1-2: Side View Dimensions..........4 Figure 1-3: Front Panel I/O Connectors & Controls ...... 5 Figure 1-4: Rear Panel I/O Connectors ........6 Figure 1-5: 12 Volt DC Connector Mechanical Specification ..9 Figure 1-6: USIM / SD Side Door.......... - Page 10 Leading EDGE COMPUTING This page intentionally left blank. List of Figures...
-
Page 11: Introduction
The DLAP-201 Series provides a wide variety of industrial I/O and visual inferencing capabilities in a compact system. With a lock- able HDMI display, two GbE ports, three USB 3.0 ports (plus a USB 2.0 OTG port for software updates), one COM port, one iso-... -
Page 12: Specifications
Leading EDGE COMPUTING 1.2 Specifications Item Description System Core Processor NVIDIA Jetson TX2 (TX2i optional) Memory 8GB 128-bit LPDDR4 Storage 32GB eMMC 5.1 Graphic Output Graphic Output 1x HDMI 2.0 with lock (3840x2160 @60fps) Front Panel I/O Interface Ethernet 2x GbE USB 3.0 3x Type-A Audio... -
Page 13: Table 1-1: Specifications
DLAP-201 Series Item Description CMOS Battery Type BR2032 Protection Reverse charge protection Mechanical Antenna Holes 4x SMA Dimensions 148(W) x 104.8(D) x 52.1(H) mm Weight 765g Mounting VESA (DIN rail optional) Environmental Operating Standard -20°C to 70°C Temperature Operating 95% @40°C (non-condensing) -
Page 14: Mechanical Dimensions
Leading EDGE COMPUTING 1.3 Mechanical Dimensions All dimensions shown in millimeters (mm). Figure 1-1: Front View Dimensions 104.80 Figure 1-2: Side View Dimensions Introduction... -
Page 15: External Layout
DLAP-201 Series 1.4 External Layout Front Panel B C D Figure 1-3: Front Panel I/O Connectors & Controls Item Name Description The reset button executes a hard reset on the Reset button system. Press this button to force the system into recovery Recovery button mode. -
Page 16: Table 1-3: Rear Panel I/O Connectors
Leading EDGE COMPUTING Rear Panel Figure 1-4: Rear Panel I/O Connectors Item Name Description CAN bus CAN 2.0B (backward compatible with 2.0A) COM port (DE-9 connector); RS-232/422/485 Serial port supported by jumper selection HDMI port HDMI 2.0 with lock USB 2.0 USB 2.0 OTG (Micro-USB) Table 1-3: Rear Panel I/O Connectors Introduction... -
Page 17: Pin Definitions
DLAP-201 Series 1.5 Pin Definitions 1.5.1 Ethernet GbE Connectors The DLAP-201 series comes with two RJ-45 connectors: NVIDIA® Jetson™ TX2 (LAN 1) Intel® I210 (LAN 2) LAN LED connection speed color indicators: Yellow (left LED): 1Gbps ... -
Page 18: Usb 3.0 Connectors
Leading EDGE COMPUTING 1.5.2 USB 3.0 Connectors The USB 3.0 ports support a USB Type-A connection, compatible with SuperSpeed, Hi-Speed, full-speed, and low-speed USB devices. It is suitable for USB peripherals including USB cameras. The following table provides details for the USB pin connections. Pin # Signal Name USB3.0_P5VA... -
Page 19: Volt Dc Connector
DLAP-201 Series 1.5.3 12 Volt DC Connector The system requires a DC power source with a screw-type con- nector. Pin Signal +12V Table 1-6: 12 Volt DC Connector Pin Definition Dimensions: mm Figure 1-5: 12 Volt DC Connector Mechanical Specification... -
Page 20: Can Bus
Leading EDGE COMPUTING 1.5.4 CAN Bus The Controller Area Network (CAN) enables communication among devices. The table below provides CAN bus pin informa- tion. Signal Description (Not connected) CAN0_Low Differential CAN signal negative level CAN0_GND CAN interface ground (Not connected) (Not connected) (Not connected) CAN0_High Differential CAN signal positive level... -
Page 21: Hdmi Connectors
DLAP-201 Series 1.5.6 HDMI Connectors The rear panel supports HDMI 2.0. Pin # Signal Pin # Signal TMDS Data2+ TMDS Data2 Shield TMDS Data2– TMDS Data1+ TMDS Data1 Shield TMDS Data1– TMDS Data0+ TMDS Data0 Shield TMDS Data0– TMDS Clock+ TMDS Clock Shield TMDS Clock–... -
Page 22: Side I/O Slots
Leading EDGE COMPUTING 1.5.8 Side I/O Slots The I/O connectors accessible from the right side panel of the DLAP-201 are described below. Figure 1-6: USIM / SD Side Door SD Card Slot For additional storage, use the side door to install or remove a user-provided SD card. - Page 23 DLAP-201 Series Orientation Insert the SIM and SD cards with the orientations shown below. Introduction...
- Page 24 Leading EDGE COMPUTING This page intentionally left blank. Introduction...
-
Page 25: Getting Started
DLAP-201 Series Getting Started 2.1 Unpacking Checklist Before unpacking, check the shipping carton for any damage. If the shipping carton and/or contents are damaged, inform your dealer immediately. Retain the shipping carton and packing materials for inspection. Obtain authorization from your dealer before returning any product to ADLINK. -
Page 26: Removing The Chassis Cover
Leading EDGE COMPUTING 2.3 Removing the Chassis Cover To access the DLAP-201’s internals, remove the underside of the chassis as follows. 1. On the front panel, remove the nut and washer from the DC12V connector and remove the two mounting screws, all indicated by red circles in the figure below. - Page 27 DLAP-201 Series 3. Slide the cover in the direction indicated by the red arrow to the position shown below. 4. Lift the cover off of the chassis. Reverse the steps above to replace the bottom cover. Getting Started...
-
Page 28: Installing Msata Module
Leading EDGE COMPUTING 2.4 Installing mSATA Module Use the following steps to install an mSATA module. 1. Insert the mSATA module into the indicated slot (under the wires) at an angle. Figure 2-1: mSATA Slot 2. Press down on the mSATA module until it is seated, then secure it with two M2.5-P-head-L5 screws (not pro- vided). -
Page 29: Installing Mpcie 3G/4G Lte Module
DLAP-201 Series 2.5 Installing mPCIe 3G/4G LTE Module Use the following steps to install an mPCIe 3G/4G LTE module. Use of the mPCIe 3G/4G LTE module requires installation of a SIM card. See Section 1.5.8 Side I/O Slots on page 12. -
Page 30: Connecting Dc Power
Leading EDGE COMPUTING 2.6 Connecting DC Power Before providing DC power to the DLAP-201, ensure the volt- age and polarity provided are compatible with the DC input. Improper input voltage and/or polarity can be responsible for WARNING: system damage. Avant de connecter le PC DLAP-201 à une source de courant continu, veuillez vous assurer de la polarité... -
Page 31: Vesa Mount
DLAP-201 Series 2.7 VESA Mount The DLAP-201 controller ships with a VESA 100 mounting bracket and four M4 screws. Follow the steps below to mount the device. 1. Attach the VESA bracket to the wall (or other suitable mounting surface) such that its keyhole-shaped mount- ing holes are oriented with the wider openings at the top. -
Page 32: Din Rail Mount
Leading EDGE COMPUTING 2.8 DIN Rail Mount The DLAP-201 controller may optionally include a DIN rail mount kit, with its own six M4 screws, in addition to the standard VESA mount kit. Follow these steps to install the DIN rail bracket. 1. -
Page 33: Internal Jumper Settings
DLAP-201 Series 2.9 Internal Jumper Settings The interior of the DLAP-201 controller features four jumper switches as shown in the figure. COM Mode Switches: SWS1601, SWS1602 AT Mode Switch: SWS1501 GPIO Switch: CN1501 SWS1602 SWS1601 SWS1501 CN1501... -
Page 34: Com Mode Switches
Leading EDGE COMPUTING 2.9.1 COM Mode Switches The COM port’s communication protocol is determined by two jumper switches: SWS1601 and SWS1602. By default they are configured for RS-232 but may be changed to RS-422 or RS-485 by setting their pins as indicated in the table below. RS-232 Switch RS-422... -
Page 35: Using The System
DLAP-201 Series Using the System 3.1 Software Configuration The DLAP-201 ships with a customized NVIDIA Linux for Tegra (L4T) image pre-installed. The latest version of this custom L4T image and other relevant files are available on our website: https://www.adlinktech.com/Products/ Deep_Learning_Accelerator_Platform_and_Server/ Inference_Platform/DLAP-201-JT2 For a non-customized version, download the TX2’s “L4T Driver... -
Page 36: Com Port Configuration
Leading EDGE COMPUTING 4. Look for “NVidia Corp.” in the output (an example is cir- cled in red in the screenshot below). If found, the host PC recognizes the client and you may proceed. If not, double-check the OTG cable connection and perform troubleshooting as needed until the client is recognized. -
Page 37: Important Safety Instructions
DLAP-201 Series Important Safety Instructions For user safety, please read and follow all instructions, Warnings, Cautions, and Notes marked in this manual and on the associated device before handling/operating the device, to avoid injury or damage. S'il vous plaît prêter attention stricte à tous les avertissements et mises en garde figurant sur l'appareil , pour éviter des blessures... - Page 38 Leading EDGE COMPUTING A Lithium-type battery may be provided for uninterrupted backup or emergency power. Risk of explosion if battery is replaced with one of an incorrect type; please dispose of used batteries appropriately. Risque d’explosion si la pile est remplacée par une autre de CAUTION: type incorrect.
-
Page 39: Getting Service
San Jose, CA 95138, USA Tel: +1-408-360-0200 Toll Free: +1-800-966-5200 (USA only) Fax: +1-408-360-0222 Email: info@adlinktech.com ADLINK Technology (China) Co., Ltd. 300 Fang Chun Rd., Zhangjiang Hi-Tech Park Pudong New Area, Shanghai, 201203 China Tel: +86-21-5132-8988 Fax: +86-21-5132-3588 Email: market@adlinktech.com...
Need help?
Do you have a question about the DLAP-201 Series and is the answer not in the manual?
Questions and answers