Advertisement
ISM MTP UT 4DA Output Board Installation Notes, cont'd
9. Connect a control device to RS-232 insert 1/2 (for
outputs 1 and 2), or insert 3/4 (for outputs 3 and
4). This allows bidirectional, pass-through control
signals to and from the control device and the
MTP devices on ports 1 and 3, and unidirectional
pass-through signals from the control device on
ports 2 and 4. Ports 1 and 2 always receive the
same RS-232 command signal, but only port 1
allows for bidirectional communications. The
same is true for ports 3 and 4, where port 3 allows
for bidirectional communications (see right).
See below for board specific SIS
ISM MTP UT 4DA configuration menu
Using the front panel menu buttons (Menu and Next), the
ISM MTP UT 4DA board configuration menu can be accessed.
From the Output Configuration screen, press Next until reaching
the #x ISM MTP menu (see the image at right). Using the front
panel adjustment knobs ({ [), change the settings as desired.
Power up input and output devices and create the desired ties.
Board specific SIS commands table
Alternatively, the ISM MTP UT 4DA board can be configured with specific SIS commands.
Command
ASCII
command
(host to switcher)
Local RS-232 ports
Enable
EX!*X@
Disable
EX!*X@
View
EX!*X@
Output Pre-peaking
Turn on
EX!*X$
Turn off
EX!*X$
View
EX!*X$
status
N X!
= ISM 824 output number, 3,5,7,8 (i.e. the slot/port occupied by the ISM MTP UT 4DA)
X@
= RS-232 number
X#
= Setting value
X$
= Sub-output number (setting for each MTP output on each card) 1,2,3,4
Extron USA - West
Extron USA - East
Headquarters
+800.633.9876
+800.633.9876
Inside USA / Canada Only
Inside USA / Canada Only
+1.919.863.1794
+1.714.491.1500
+1.919.863.1797 FAX
+1.714.491.1517 FAX
commands.
™
Response
(switcher to host)
X!
*1LRPT
Lrpt
X!
Lrpt
*0LRPT
X#]
LRPT
X!
*1OPEK
Opek
X!
*0OPEK
Opek
X# ]
OPEK
0 = insert 1/2, 1= insert 3/4
0 = off, 1= on
Extron Europe
Extron Asia
+800.3987.6673
+800.7339.8766
Inside Europe Only
Inside Asia Only
+31.33.453.4040
+65.6383.4400
+31.33.453.4050 FAX
+65.6383.4664 FAX
© 2009 Extron Electronics. All rights reserved
RS-232 Commands
Tx Rx
INSERT 1/2
LOCAL
AUDIO OUTPUT
INSERT 3/4
L
R
Tx Rx
RS-232 Commands
Transmit (Tx)
Receive (Rx)
Ground (Gnd,
)
Additional description
X@
*1
]
Enable RS-232 insert
control output
X@
*0
]
Disable RS-232 insert
controlling output
View the RS-232 status
output
Turn pre-peaking on for output
X$
]
*1
X!
to MTP sub-output
]
Turn pre-peaking off for output
X$
*0
X!
to MTP sub-output
View the pre-peaking status
for output
Extron Japan
Extron China
+81.3.3511.7655
+400.883.1568
+81.3.3511.7656 FAX
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
.
BUFFERED OUTPUTS
RS 232
1
2
3
BUFFERED OUTPUTS
1
Bidirectional
Output Card
Configuration
#x ISM MTP UT 4DA
<Off>
RS-232 Insert 1/2
<Off>
RS-232 Insert 3/4
<Off>
X@
X!
.
X@
X!
.
X#
X!
.
X$
X$
X!
.
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX
4
Unidirectional
2
3
4
Select Ouptut
Next
Prepeaking #x
On
Next
On
Next
On
Next
to
for
.
.
X#
68-1123-60
Rev A
02 09
Advertisement
