Advertisement
Quick Links
APPLICATION
Jeep Wrangler JL 4Dr
AMP RESEARCH TECH SUPPORT 1-888-983-2204 (Press 2) Monday - Friday, 7:00 AM - 5:00 PM PST
Invented, engineered and manufactured exclusively by AMP Research in the USA. May be covered by one of the following patents:
6,641,158; 6,830,257; 6,834,875; 6,938,909; 7,055,839; 7,380,807; 7,398,985; 7,584,975 ©2012 AMP Research. All rights reserved.
Printed in USA.
www.amp-research.com
I N S T A L L A T I O N G U I D E
2018 - 2019
1/10
AMP Part #
75132-01A
INSTALLATION TIME
3-5 Hours
Professional installation recommended
SKILL LEVEL
1 2 3
4= Experienced
TOOLS REQUIRED
q Safety goggles
q Measuring tape
q 10 mm socket
q 13 mm socket
q 1/2" socket
q Ratchet wrench and extension
q Wire crimpers
q Wire stripper / cutter
q
3 /16" hex key wrench (allen wrench)
q
4mm hex key wrench ( allen wrench )
q
Electrical tape
q
Weather proof caulking (silicone sealer)
q
Silicone spray
WARRANTY
5-Year Limited Warranty
IM75132 rev 01.02.20
4
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for AMP Research PowerStep 75132-01A
Summary of Contents for AMP Research PowerStep 75132-01A
- Page 1 AMP RESEARCH TECH SUPPORT 1-888-983-2204 (Press 2) Monday - Friday, 7:00 AM - 5:00 PM PST Invented, engineered and manufactured exclusively by AMP Research in the USA. May be covered by one of the following patents: 6,641,158; 6,830,257; 6,834,875; 6,938,909; 7,055,839; 7,380,807; 7,398,985; 7,584,975 ©2012 AMP Research. All rights reserved.
-
Page 2: Exploded View
A M P R E S E A R C H P O W E R S T E P – J e e p W r a n g l e r J L EXPLODED VIEW • Motor • Hex Head Bolt CAUTION: HANDLE WITH CARE. - Page 3 A M P R E S E A R C H P O W E R S T E P – J e e p W r a n g l e r J L End cap left (x1) End cap right (x1) T-nut insert (x2) Socket cap screw (x2) Nut plate (x2)
- Page 4 A M P R E S E A R C H P O W E R S T E P – J e e p W r a n g l e r J L Washer Socket Cap M8 Hex Bolt w M8 Button LED Light Bracket Conical washer...
- Page 5 A M P R E S E A R C H P O W E R S T E P – J e e p W r a n g l e r J L Install Rear Idler Linkage: Locate rear most mounting hole set.
- Page 6 A M P R E S E A R C H P O W E R S T E P – J e e p W r a n g l e r J L Slide motor assembly onto drive shaft and mounting Remove fuses from Power Step Wire Harness.
- Page 7 A M P R E S E A R C H P O W E R S T E P – J e e p W r a n g l e r J L Route the two Wire Harness legs down over the wheel wells toward Motor Linkages, long leg across to the driver side.
- Page 8 A M P R E S E A R C H P O W E R S T E P – J e e p W r a n g l e r J L White Mount door trigger module to wire Plug harness in kick panel area.
- Page 9 A M P R E S E A R C H P O W E R S T E P – J e e p W r a n g l e r J L On driver side, run Wire Harness leg down and along underside of the vehicle floor and frame to front Drive Linkage.
-
Page 10: Final System Check
A M P R E S E A R C H P O W E R S T E P – J e e p W r a n g l e r J L Check that all doors activate the Power Step and the LED Lights work when doors open and close. -
Page 11: Year Limited Warranty
5-YEAR LIMITED WARRANTY AMP RESEARCH warrants this product to be free from defects in material and workmanship for FIVE (5) YEARS FROM DATE OF PURCHASE, provided there has been normal use and proper maintenance. This warranty applies to the original purchaser only.
Need help?
Do you have a question about the PowerStep 75132-01A and is the answer not in the manual?
Questions and answers
Had this installed in the shop were purchased they installed all the wires etc. the brackets provided were the wrong ones and they supplied the new ones I installed the new brackets and the boards only they were set in the down positing when I hooked them up and opened the doors they went up but into position but now will not come down when door is opened what do I need to do now so they work properly?
To fix the AMP Research PowerStep 75132-01A so that the steps come down when the doors are opened:
1. Check for any obstruction blocking the running board. If found, remove it.
2. Open and close the door to reset normal operation.
3. Make sure the plug reassembly is correct. The lever arm of the plug must be fully rotated and locked in the open position.
4. Ensure the wire harness is properly connected to the motor and secured.
5. Check the door trigger wiring connections to the vehicle BCM as per the wiring chart.
If these steps do not resolve the issue, further inspection of the wiring and motor may be needed.
This answer is automatically generated