Advertisement
A
Piease note the install(ltion
decoder interface(" r
~
d with all ROCO locomotives having
We recommend,
in
addition
to
tlw
c,pPcific
locomotrv<' mstallation
instructions, the following
procedure:
1.
Remave housing
and
dctacll tlw
rPversing
modul<' or thc already
installed decoder from th
interface.
2.
Insert the
decoder
plug into llw
lllt<'rlcJce
(Fig. 1)
so
tllrtt
c,icle of the
decoder plug with red/orange
wire at the
side of the intrrf,lu' ITlcllked
with
+
or
+
(polc1rity according
to NMRA/NEM rules,
i.e.
the locomotive
moves
with tlw driwr
' c , cab
no.1
fclCinq
lorward).
3.
lnstall the decoder
in
a sui tai>IP
locc~lron
with
in
tlw
locomotive. No part of the
decoder
must b
tauehing metal
parts
of the
locornotrve
! lf
necessmy
the
location of the decoder must be
insulated with insulation
tape
to
protect
the
decoder. The
insulation
must be attached to
the metal parts of the
locomotive,
but
NOT
to
the dccoder (e.g. by
winding
the
insulation
tape around the
decoder!).
1 hic,
could
Iead
to
failur<' olthe
decoder due to
overheating.
Da mag
claims caused
by such failurps
Cdnnot
be
acceptctl
The factory used
heat shnnk
tui>IIHJ
dround
the
drmciPr ensures a
sufficient heat
dissipation and
should not be
removed.
4.
lf necessary the
decoder
can
Iw
wcurPd
in
the
de
s~r<'d
locc~tion
with double-sided tape.
Operational test
lf the locomotive lights do
not
opercl l<' ,
tlw
eireoder
was inc,Ntccl incorrectly into
the
interface.
Reinscrl
decoder turned by
180°
in the
interfclCP.
locomotive address
The factory-set default
Motorola
lt •
aclclr<"'"
of
the
decodN
ic, 03
.
Operation on analog layou
A ROCO locomotive equipped with
c1
drcodrr
can also
IH'
run
on a
conventional Iayout. To
changc
direction of travel the control knob
of
the
controller must first
be
set
to zero.
Only
tlwn
trlll
the direction of travel be selcctrd
wrth
,m
ohvious and
lorHJrr
switching
pulse.
The
brightness of
tiH•
lamps depends on the
speed of
tiH'
tr<1111.
!Iu•
lrghts
can
notiH' turned off
and
a
possibly
installed c,pec
rdl
function F1 will not
operatc.
Rcprogrt1mming
of
previously
set
addresses
and functions is not
possible while in analog
operation.
list of supported RPqtster
resp- c
v
s
The following Iist
informs aboul
tlw
pro<Jr
c
unming
Cflp,rl>rlrtr<''>
of
the decoder.
We
recommrnd
to
test your
locomotive/railcar
with rl'CJdlcl to
starting voll
dCJP,
ilcceleration, braking
and
maxrmum
speed du ring operations to
check
rf tlww
c
haracteristic
c,
.ttl'
wt conforming
to
your
wishes
BEFORf
changing the factory-set dcfault
wttings.
Programming lnstru\.tions :
v•
.Jiärklin
*
6020/6021
Caution:
>
The cantroll er must be sct tu
"0"
.
>
No other locomotive
except
tlw
oru'
to Iw programml'd
rnt~y
be
on
thc tracks.
>
While
programming
pay
attPntron
to tlw
flashing
ol tlw loc
ornotiv<'
hcfldlights.
>
Any number of
changes/adjuc,tnwnl'.
nrn
be
madc
,,.,
lorHJ
tl'>
tlw cl!'coder is in
programming mode.
Advertisement
