Table of Contents
Advertisement
Instruction Manual Crimping Tool
K-EP 1342
使用说明书
4.
Remarks in respect of the determined
use
Before starting any work on electrical appliances it must
be safeguarded that there are no live parts in the imme-
diate assembly area of the user. If this not possible spe-
cial precaution measures (
e.g. acc. to EN 50110-1
near live parts must be provided.
Keep your working area clean and tidy. Do not use this
tool when you are tired, on drugs, had alcohol or if you
are medicated.
The XXX-L is also available as an XXX-L INS with an in-
sulated head which is specially designed for working near
live lines.
4.1 Operation of the unit
Cycle: see pictures in front
The crimping head should be turned into the desired po-
sition before starting the crimping cycle. It is signi cantly
easier to turn the crimping head in a pressure free state.
Attention
After having terminated the working cycle and
prior to changing the dies remove battery to
avoid unintended use. Avoid unintended starts.
Make sure the switch is in the off position before
plugging in.
Attention
Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts.
Attention
Keep proper footing and balance at all times.
Attention
Use safety gear and always wear eye protec-
tion.
4.2 Explanation of the application range
Attention
Do not crimp on live cables or conduc-
tors. The tool is not insulated.
The unit is a hand held tool and it is not supposed to be
restrained in a vise. It is not allowed to use the tool in a
stationary application.
The tool is not designed for continued operations. After
a sequence of approximately 50 completed cycles you
have to make a break of 15 min. to give the tool time to
cool down.
Attention
Too intensive use can cause heat damages for
the tool
Attention
During the operation of electric engines sparks
can occur which might ignite highly in ammab-
le or explosive liquids and materials
Attention
Electric-hydraulic tools should not be operated
in pouring rain or under water.
4.3 Mounting instructions
Please read the assembly instructions in our general ca-
talogue.
CN.2P015 06/2014 KN
HE.15508_A © 06/2014
Attention
Even if the code number is identical only those
dies should be used which are suitable for the
material.
4.4 Service and maintenance instruction
) for working
For every day service the tool has to be cleaned and dried
after each use. The battery cartridge and the charging unit
have to be protected against humidity and dust.
The electric-hydraulic unit is equipped with a controller
enabling the user to see when the next service is due by
ashing for 20 sec. at the end of a working cycle.
The unit must be sent to an authorized service center
(ASC) after reaching 10.000 cycles or at the latest after
one year. During this service worn out parts will be ex-
changed, safety relevant components checked and pos-
sibly replaced precautiously. This provision serves your
safety and avoids failures through fatigue.
Attention
Maintain power tools thoroughly. Check for
functionality or jamming of moving parts,
breakage of parts and any other condition that
may affect the power tools operation.
Attention
Do not damage the seals of the tool. If the seal
is damaged the warranty claim is void.
Attention
Have damaged parts repaired by a quali ed ex-
pert or by a Klauke ASC before use.
5
Troubleshooting
a.) Constant ashing/indicating of the red LED (pic 1.1)
or the occurence of an acoustical warning signal.
see table 1. If the failure can not be solved return the
tool to the nearest service center (ASC).
b.) The tool loses oil.
Return the unit to the manufacturer. Do not open it and
damage the seal of the tool.
6.
Technical Data
Weight
(incl. battery):
Crimping force:
Stroke
Battery voltage:
Battery capacity
Charging time:
Crimping time:
Crimps
per battery:
Hydraulic oil:
Environmental
temperature:
Sound level:
Vibrations:
Dimensions:
Assembled by Klauke in China
from globally sourced components
6,55 kg
approx. 120 kN
42 mm
18 V
3 Ah (K-RAL2)
60 min. (K-RAL2)
approx. 10 s to 14 s
(depending on the connector size)
approx. 110 crimps
(Cu 150 mm² DIN 46235)
Shell T32
-12°C to +40°C
< 70 dB (A) in 1m distance
< 2,5 m/s²
See Picture 2
GB
08
2
Advertisement
Table of Contents
