Avaya G450 Manual
  1. Manuals
  2. Brands
  3. Avaya Manuals
  4. Gateway
  5. G450 Manager
  6. Manual

Avaya G450 Manual

Branch gateway, configuring v.150.1
Hide thumbs Also See for G450:
Table of Contents

Advertisement

Quick Links

Download this manual
Configuring V.150.1 on the Avaya G450
Branch Gateway
Issue 1
July 2012

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the G450 and is the answer not in the manual?

Questions and answers

Related Manuals for Avaya G450

Summary of Contents for Avaya G450

  • Page 1 Configuring V.150.1 on the Avaya G450 Branch Gateway Issue 1 July 2012...

  • Page 3: Table Of Contents

    Adding and removing the MP160......................7 Chapter 3: Configuring V.150.1 in Communication Manager.......... Configuring V.150.1........................... 13 IP codec set.............................. 14 IP codec set: page 2......................... 15 IP codec set: page 3......................... 19 Index............................. Configuring V.150.1 on the Avaya G450 Branch Gateway July 2012...
  • Page 4 Configuring V.150.1 on the Avaya G450 Branch Gateway July 2012...

  • Page 5: Chapter 1: Introduction

    - Firmware 32.16 or higher Note: V.150.1 is not supported on the G430. • At least one MP160 Media Processor Module installed on the G450 main board. See Adding and removing the MP160 on page 7 for instructions on installing the MP160.
  • Page 6 Introduction Configuring V.150.1 on the Avaya G450 Branch Gateway July 2012 Comments? infodev@avaya.com...

  • Page 7: Chapter 2: Installing The Mp160

    1 or 2 Combination #4 Important: You can only install the MP160 in slots 2 and 4 on the G450 1.x or slots 1 and 2 on the G450 2.x. (see Figure 2: Location of MP160 module slots in a G450 1.x...
  • Page 8 Attach the correct standoff according to the hardware version of the G450. Using the wrong standoff will prevent you from installing the MP160 correctly. About this task You do not need to configure the G450 when you install an MP160. However, you must configure V.150.1 in Communication Manager. See Configuring V.150.1...
  • Page 9 Adding and removing the MP160 Figure 2: Location of MP160 module slots in a G450 1.x Table 1: Figure notes: 1. MP20 or MP80 module slot 2. MP20,MP80 or MP160 module slot 3. MP20 or MP80 module slot 4. MP20, MP80 or MP160 module slot Configuring V.150.1 on the Avaya G450 Branch Gateway...
  • Page 10 Installing the MP160 Figure 3: Location of MP160 module slots in a G450 2.x Table 2: Figure notes: 1. MP20, MP80 or MP160 module slot 2. MP20, MP80 or MP160 module slot 3. MP20 or MP80 module slot 4. MP20 or MP80 module slot 3.
  • Page 11 Adding and removing the MP160 Figure 4: Adding or removing an MP160 in a G450 4. Push the module in all the way. Do not use too much force. 5. Flatten the module so it is flush with the main board.
  • Page 12 Installing the MP160 Configuring V.150.1 on the Avaya G450 Branch Gateway July 2012 Comments? infodev@avaya.com...

  • Page 13: Chapter 3: Configuring V.150.1 In Communication Manager

    Communication Manager Configuring V.150.1 Before you begin V.150.1 is only supported by MP160 Media Processor modules installed in the G450. You must enable RFC2833 Telephony Events on SIP trunks and IGCs. Procedure 1. Access the Communication Manager administrative SAT interface.

  • Page 14: Ip Codec Set

    , where n is the codec set number. change ip-codec-set n Related topics: IP codec set: page 2 on page 15 IP codec set: page 3 on page 19 Configuring V.150.1 on the Avaya G450 Branch Gateway July 2012 Comments? infodev@avaya.com...

  • Page 15: Ip Codec Set

    Codec set. Note: Transporting modem signals over IP between Avaya Communication Manager systems (and Media Gateways) is a proprietary implementation except for the selection of the V.150.1 Modem Relay codec choice. This means for modem transport interoperability with third party gateways, that the v150mr is the recommended mode of operation.
  • Page 16 Turn off special fax handling when using this codec set. In this case, the fax is treated like an ordinary voice call. relay For users in regions using this codec, use Avaya relay mode for fax transmissions over IP network facilities. pass-through For users in regions using this codec, use pass-through mode for fax transmissions over IP network facilities.
  • Page 17 This mode facilitates ITU-T V.32 relay over IP on non-signaled inter- gateway connections in support of SCIP/FNBDT communication. V.8 modem signaling is not supported in this mode. Configuring V.150.1 on the Avaya G450 Branch Gateway July 2012...
  • Page 18 Turn off special TTY handling when using this codec set. In this case, the TTY transmission is treated like an ordinary voice call. With a codec set that uses G.711, this setting is required to send TTY calls to non-Avaya systems. However, there might be errors in character transmissions.

  • Page 19: Ip Codec Set

    SPRT TC1 Payload Size Valid Entry Usage 132 to 256 bytes The maximum payload size for SPRT Transport Channel 1. Default size is 132 bytes. Configuring V.150.1 on the Avaya G450 Branch Gateway July 2012...
  • Page 20 140 to 256 bytes The maximum payload size for SPRT Transport Channel 3. Default size is 140 bytes. Note: Maximum SPRT Payload sizes may vary across different gateways depending on the firmware and hardware version. Configuring V.150.1 on the Avaya G450 Branch Gateway July 2012 Comments? infodev@avaya.com...
  • Page 21 (increments of 10 mSec) SPRT Timer TC2-TA01 Valid Entry Usage 50 mSec to 150 The Ack timer for channel 2. Default is 90 mSec. mSec (increments of 10 mSec) Configuring V.150.1 on the Avaya G450 Branch Gateway July 2012...
  • Page 22 The redundancy option allows the protocol exchange to be provided with 1 or more packets of identical information to provide more robust transport across an IP-based network. Default is 3 packets. Configuring V.150.1 on the Avaya G450 Branch Gateway July 2012 Comments? infodev@avaya.com...

  • Page 23: Index

    Maximum Call Rate for Priority Direct-IP Multimedia . Modem Mode ............. Modem Relay Preferred (NoAudio) ......TDD/TTY Mode ............MP160 modules ............channels, number of ..........V..150.1 ..............configuring ............V.150.1 ................. requirements ............Configuring V.150.1 on the Avaya G450 Branch Gateway July 2012...

Table of Contents