Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Omicron Lab OTMC 100
Summary of Contents for Omicron Lab OTMC 100
- Page 1 OTMC 100 Quick Start Guide Smart Measurement Solutions ®...
- Page 2 Mozilla Foundation. Google Chrome is a trademark of Google Inc., used with permission. Apple and Bonjour are registered trademarks of Apple Inc. OMICRON Lab and Smart Measurement Solutions are registered trademarks of OMICRON electronics GmbH.
-
Page 3: Table Of Contents
Mounting instructions ......................10 3.3.1 Mounting instructions for mast mounting ................... Connecting OTMC 100 to an Ethernet network ............. 12 Accessing OTMC 100 from a Computer ................. 14 System requirements ......................14 Accessing the OTMC 100 web interface ................14 Troubleshooting ....................... -
Page 4: Introduction
This OTMC 100 Quick Start Guide provides short information on how to install and access OTMC 100. It is intended as an aid for the user to install OTMC 100 and take it into operation quickly and easily. The OTMC 100 Quick Start Guide thus provides only a small subset of information available for OTMC 100. - Page 5 Introduction • OTMC 100 is an SELV device (Safety Extra Low Voltage) which is supplied with power by Power over Ethernet (PoE according to IEEE 802.3af). It may only be connected to Ethernet network ports or Power over Ethernet power supplies.
-
Page 6: Device Overview
Ø 115.5 mm variant 4 and serial number OTMC 100 does not provide an ON/OFF switch. The device automatically powers up after supply voltage is provided via Ethernet (PoE). The LED indicates the device status: LED continuously off OTMC 100 is not supplied with power via the RJ45 Ethernet connector (→... - Page 7 Initiate a factory reset to reset the device configuration to the factory defaults (→ see Troubleshooting on page 18). • Initiate a device reboot (→ see "Performing a reboot of OTMC 100" in the OTMC 100 Series User Manual). OMICRON...
-
Page 8: Mounting
180° vertically to the sky and 360° horizontally around the device. The view to the sky must not be blocked by any objects. This is usually given when mounting OTMC 100 on a roof or a sufficiently high mast. Refer to the figure below. - Page 9 Mounting Always mount OTMC 100 in an upright position with the protective cap to the top, as shown in the figure below. The RJ45 connector on the base plate of OTMC 100 must point vertically downwards. Do not mount OTMC 100 inclined to any side or with the base plate to the top!
-
Page 10: Mounting Instructions
3.3.1 Mounting instructions for mast mounting The mounting kit delivered with OTMC 100 contains the following parts: • 1 mast clamp consisting of 2 clamping jaws and 4 fastening screws M6 x 110 with lock washers •... - Page 11 The threaded holes in the base plate are only 9 mm deep. Insert the connecting pipe (4) to the clamping blocks on the mast clamp and OTMC 100 as shown in the figure. Align OTMC 100 in an upright position as shown in...
-
Page 12: Connecting Otmc 100 To An Ethernet Network
OTMC 100 automatically powers up after inserting the RJ45 plug and providing supply voltage to OTMC 100. After the device is supplied with voltage, the LED first lights up red for approx. 15 s during the boot process and then changes to green to indicate operational readiness. - Page 13 Connecting OTMC 100 to an Ethernet network The following figure shows the general arrangement of OTMC 100, the surge protection device and the PoE injector (if necessary). Surge protection device Surge protection device PoE injector Mains Ethernet network port Ethernet network port...
-
Page 14: Accessing Otmc 100 From A Computer
After that, a network IP address is assigned automatically in order to connect the device to the network. If a DHCP server is available in the network, the IP address is assigned by the DHCP server. If not, OTMC 100 automatically selects and assigns a link-local IPv4 and IPv6 address by itself. System requirements Your computer must fulfill the following requirements to access the OTMC 100 web interface: •... - Page 15 OMICRON Device Link will then display an IP configuration page. In this page, select Use the following IP address and enter the IP address of your OTMC 100, or enter an IP address of your choice to assign a new IP adress to your OTMC 100. Click the Subnet mask field to automatically fill a subnet mask and then click Apply to connect to your OTMC 100.
- Page 16 Click the OTMC 100 entry and select Open web interface. 6. The web interface is opened in a web browser. Password protection is disabled by default. If a password has been defined for your OTMC 100, a login dialog is displayed. Enter your password and click Login.
- Page 17 Accessing OTMC 100 from a Computer 8. Refer to the OTMC 100 Series User Manual for information on how to configure and operate OTMC 100. Section "Next steps to set up OTMC 100" in the OTMC 100 Series User Manual provides an overview of steps required to configure OTMC 100 according to your needs.
-
Page 18: Troubleshooting
OTMC 100 automatically powers up after inserting the RJ45 plug and providing supply voltage to OTMC 100. After the device is supplied with voltage, the LED first lights up red for approx. 15 s during the boot process and then changes to green to indicate operational readiness. In case of operational problems with OTMC 100, please use the following table to solve the problem. -
Page 19: Performing A Factory Reset (Reset To Factory Defaults)
Troubleshooting LED flashes green OTMC 100 is in the recovery mode, waiting for new software. Refer to chapter "Operating OTMC 100" of the OTMC 100 Series User Manual. The password dialog is Perform a factory reset directly on the OTMC 100 device (→ see displayed when accessing "Performing a factory reset (reset to factory defaults)"... -
Page 20: Open Source Software License Information
OTMC 100 Quick Start Guide Open Source software license information Parts of the OTMC 100 software are under OMICRON license, other parts are under Open Source software licenses. To view the license information on the Open Source software used in OTMC 100, please launch the OTMC 100 web interface and click the License Information hyperlink in the bottom right corner. -
Page 21: Support
Support Support When you are working with our products we want to provide you with the greatest possible benefits. If you need any support, we are here to assist you. 24/7 Technical Support - Get Support www.omicron-lab.com/contact/get-support/ Offering our customers outstanding support is one of our top priorities. At our technical support hotline, you can reach well-educated technicians for all of your questions. - Page 22 ENU 1066 03 01...