Subscribe to Our Youtube Channel
Related Manuals for Sports Attack SNAP ATTACK
Summary of Contents for Sports Attack SNAP ATTACK
- Page 1 FOOTBALL MACHINE SNAP ATTACK™ FOOTBALL MACHINE PATENTS APPLIED FOR INSTRUCTION MANUAL OPERATION · SETUP · USE & CARE · SERVICE SPORTS ATTACK LLC. | 800.7 1 7.4251 | www.sportsattack.com...
-
Page 2: Table Of Contents
. This manual contains the information needed to properly set up the Snap Attack Football Machine, and to use, care for and maintain the Snap Attack in a manner which will ensure its optimum performance . -
Page 3: Warranty Statement
. If a service person is needed, Sports Attack will pay the pre-approved for return . It is the customer’s labor charge to get your machine back in working order . -
Page 4: Safety Instructions
Check that the speed control is at “0” before turning the throwing wheels “ON” . INJURY HAZARD Do not allow anyone to walk in front of the Snap Attack Football Machine if it is connected to electrical power . Keep hands away from throwing... -
Page 5: Component View
. Maintain adequate fuel in the FIGURE 2 generator at all times . Throwing Head & Undercarriage View 4 . Turn the Snap Attack power Speed Throwing Head Control Dial (F) switch “OFF” before shutting Attachment Bolts (2) off the generator and before unplugging the Snap Attack . -
Page 6: Set-Up & Preparation
SHUTTING DOWN & TRANSPORTING TURNING SNAP ATTACK “OFF” 1 . Turn the power switch “OFF” and unplug Snap Attack from the power source . TRANSPORTING WITH STAND 1 . Be sure machine is turned “OFF” and wheels are not turning . -
Page 7: Passing, Punting, Kickoff
. 6. Lift rear leg and roll machine (See Figure 5). PASSING, PUNTING & KICKOFF The Snap Attack is able to simulate both right-hand and left-hand spins . Two wheel tilt handles G (See Figure 1) are located underneath both motors, one on each side, and are used to change the angle of the wheels to provide either end-over- Figure 5 Lift rear leg and roll . -
Page 8: Replacement
COMPONENT REPLACEMENT THROWING WHEEL REPLACEMENT 1 . Turn the throwing wheels “OFF” and unplug the power cord . Remove 4 bolts holding the top wheel guard to the bottom wheel guard . 2 . Hold the wheel so that it cannot move . Turn the keyway retaining bolt counter-clockwise using a box end wrench (See Figure 6). - Page 9 POWER CORD WIRE COMPONENT REPLACEMENT (continued) Black (#1) CONTROLLER REPLACEMENT On/Off switch White (#2) 1 . Turn the power switch “OFF” and unplug the power cord . N on green control board 2 . Remove knob from the controller . Green (#3) 3 .
-
Page 10: Exploded View
Cane Tip EXPLODED VIEW - SNAP ATTACK™ Swivel Assy Handle Horizontal Swivel Lock Locking Pin Frame to Swivel Undercarriage Assy Handle, Elevation 7a Bolt, Carriage ” Nylon Nut Disc, Elevation 110V 8a bElevation Clutch 220V Throwing Head Assy 9a Snapping Tube Elevation Mount... -
Page 11: Parts List
To order additional PARTS LIST parts please contact: PART NO. DESCRIPTION QTY PER Sports Attack Customer Service Dept . 280-1003 Cane Tip 800 .717 .4251 532-0007 775 .345 .2883 531-1046 Swivel Assy 533-2016 Handle Horizontal Swivel Lock 340-2009 Locking Pin Frame to Swivel... -
Page 12: Attaching Cart Clamp
CART CLAMP KIT ATTACHING OPTIONAL CART CLAMP Item ______________________ Designed to fit 2½” to 4” round or square post Clamp 1 . Insert clamp bolt through top plate . Loosely attach washer and nut . Finger tighten . 2 . Put 3 bolts through sides of clamps . Slide unit over post, then attach fourth bolt . Top Plate 3 .
Need help?
Do you have a question about the SNAP ATTACK and is the answer not in the manual?
Questions and answers