Table of Contents
Advertisement
Quick Links
S
P
-
5
0
S
P
-
5
0
2x8 HDMI Splitter over Cat.X
User Manual
To avoid EMI issue, complete STP Cat6 cable is strongly recommended!
1
8
M
1
8
M
rev: 131028
Made in Taiwan
The SP-5018M
2x8 HDMI Splitter over Cat.X
and requirements, and has been certified for international use. However, like all electronic
equipments, the SP-5018M should be used with care. Please read and follow the safety instructions
to protect yourself from possible injury and to minimize the risk of damage to the unit.
● Follow all instructions and warnings marked on this unit.
● Do not attempt to service this unit yourself, except where explained in this manual.
● Provide proper ventilation and air circulation and do not use near water.
● Keep objects that might damage the device and assure that the placement of this unit is on a
stable surface.
● Use only the power adapter and power cords and connection cables designed for this unit.
● Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device
before cleaning.
TABLE OF CONTENTS
INTRODUCTION ..................................................................................................................... 1
FEATURES .............................................................................................................................. 1
PACKAGE CONTENTS .......................................................................................................... 1
SPECIFICATIONS ................................................................................................................... 2
PANEL DESCRIPTIONS ......................................................................................................... 3
HARDWARE INSTALLATION ................................................................................................. 3
CONNECTION DIAGRAM ...................................................................................................... 4
IR CONTROL ........................................................................................................................... 5
EDID LEARNING ..................................................................................................................... 5
DIP SWITCH SETTING ........................................................................................................... 6
PIN DEFINITION ..................................................................................................................... 7
NOTICE ................................................................................................................................... 8
WARRANTY ............................................................................................................................ 9
has been tested for conformance to safety regulations
Advertisement
Table of Contents
Related Manuals for GoMax Electronics SP-5018M
Summary of Contents for GoMax Electronics SP-5018M
- Page 1 However, like all electronic equipments, the SP-5018M should be used with care. Please read and follow the safety instructions 2x8 HDMI Splitter over Cat.X to protect yourself from possible injury and to minimize the risk of damage to the unit.
- Page 2 13 Watts [max] 1.5 Watt [max] 0.1 Watt [max] Operation temperature 0~40°C [32~104°F] ● 1x SP-5018M ● 1x IR Remote control Storage temperature -20~60°C [-4~140°F] ● 1x Rack-mounting ear set ● 1x DC 5V 4A in-line with C7 power cord...
- Page 3 PANEL DESCRIPTIONS CONNECTION DIAGRAM Rear Panel Power: Power on/off switch +5V DC: Power jack for 5V DC HDMI INPUT 1~2: Connect to one HDMI source here EDID & Audio: DIP Switch (see more detail in the DIP SWITCH SETTING section) INPUT Selection: Push-in button for switching between HDMI INPUT 1 and HDMI INPUT 2 Cat.X OUTPUT 1~8: Link to each HDMI display via a Cat-5/5e/6 cable with a HDMI over CAT5 receiver CV-735 or CV-715s...
- Page 4 By setting at this mode, the users may encounter compatibility issue among 4. Reboot the SP-5018M and you should see the red LED of the INPUT 1 on the front panel will keep different kinds of HDMI sources and displays. If you cannot get the audio and/or video output blinking to indicate the EDID learning sequence is underway.
- Page 5 PIN DEFINITION NOTICE HDMI 1. If the DVI or HDMI device requires the EDID information, please use EDID Reader/Writer to retrieve and provide DVI or HDMI display EDID information. 2. All HDMI over Cat.X transmission distances are measured using Belden 1583A CAT5e 125MHz UTP cable and ASTRODESIGN Video Signal Generator VG-859C &...
- Page 6 SELLER will NOT be liable for direct, indirect, incidental, special, or consequential damages resulting from any defect or omission in this manual, even if advised of the possibility of such damages. Also, the technical information contained herein regarding the SP-5018M features and specifications is subject to change without further notice.
Need help?
Do you have a question about the SP-5018M and is the answer not in the manual?
Questions and answers