Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ekwb CPU Lignum
Summary of Contents for ekwb CPU Lignum
- Page 1 CPU Lignum CPU WATER BLOCK...
- Page 2 The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates. Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.
-
Page 3: Table Of Contents
TABLE OF CONTENT GENERAL INFORMATION ON WATER BLOCK COMPATIBILITY SUPPORT AND SERVICE WHAT IS ENCLOSED SOCIAL MEDIA QUICK INSTALLATION GUIDE REPLACING THE JET PLATE PROCEDURE INSTALLING THE WATER BLOCK LGA-2011(-3) / 2066 SOCKET MOTHERBOARDS LGA-115X SOCKET MOTHERBOARDS AMD® SOCKET MOTHERBOARDS - 3 -... -
Page 4: General Information On Water Block Compatibility
- Intel® Socket LGA-115x - Intel® Socket LGA-2011(-3) / 2066 - AMD® socket AMx and FMx WHAT IS ENCLOSED The following items are enclosed with each EK-CPU Lignum - AMD socket mounting plate water block: - Allen (hex) key 2.5mm - EK-CPU Lignum water block. -
Page 5: Replacing The Jet Plate Procedure
REPLACING THE JET PLATE PROCEDURE STEP 1 Wood cover Please observe the table below to determine the optimal combina- tion of insert and jet plate for your type of socket: Double sided adhesive tape Socket Optimal Jet LGA-115x Water block top LGA-2011 Gasket LGA-2066... -
Page 6: Installing The Water Block
STEP 2 Unscrew the four M4 screws in counter-clock-wise direction from the bottom of the water block using enclosed 2,5mm Allen key to release the assembly, consisting of water block top and jet plate. Upon replacing the jet plate please reassemble the water block as shown on the in STEP 1 and STEP 2 pictures. - Page 7 STEP 2 Cleaning the CPU: Wipe the CPU’s contact surface (by using non– abrasive cloth or Q-tip, as shown on sample photo). Non-abrasive Applying thermal compound: On a clean IHS, apply a line of cloth thermal compound and spread it over the whole CPU heat spreader (IHS) with a credit card or equivalent - see sample photo on left.
- Page 8 STEP 4 Placing Wood cover: Wood cover Before proceeding with the installation It is mandatory to remove the protective foil from the backside of the water block. Place Wood cover over the water block. Then - using your fingers only, press Wood cover on water block.
-
Page 9: Lga-115X Socket Motherboards
LGA-115x SOCKET MOTHERBOARDS STEP 1 If already installed, please remove the motherboard from your Outer part computer and place it on an even surface with front facing down. STEP 2 Preparing backplate rubber gasket The enclosed rubber gasket is essential part of the backplate and mounting system and must be used every time you install this water block on your motherboard. -
Page 10: Amd® Socket Motherboards
STEP 4 Install four (4) M4 thumb screws onto your motherboard. It is mandatory to put 0.7 mm plastic washer underneath each of the M4 thumb screws. Tighten the screws to the metal backplate until you reach the end of the M4 Thumb thread. - Page 11 STEP 4 UNC 6-32 Removing of the original plastic hold-down clamps and the Screws AMD® factory backplate factory backplate: Using Philips-head screwdriver remove the four UNC 6-32 screws securing the original plastic hold-down clamps around the socket as shown on the sketch. Remove the original AMD® backplate and the hold-down clamps and store them away.
-
Page 12: Support And Service
SUPPORT AND SERVICE For assistance please contact: http://support.ekwb.com/ EKWB d.o.o. Pod lipami 18 1218 Komenda Slovenia - EU SOCIAL MEDIA EKWaterBlocks @EKWaterBlocks ekwaterblocks EKWBofficial ekwaterblocks...
Need help?
Do you have a question about the CPU Lignum and is the answer not in the manual?
Questions and answers