Smith & Noble Honeycomb Shades Step By Step Installation Instructions
Bottom up motorization
Hide thumbs
Also See for Honeycomb Shades:
- Step by step installation instructions (11 pages) ,
- Operating & programming manual (9 pages) ,
- Step by step installation instructions (15 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Smith & Noble Honeycomb Shades
Summary of Contents for Smith & Noble Honeycomb Shades
- Page 1 STEP BY STEP INSTALLATION INSTRUCTIONS Honeycomb Shades Bottom Up Motorization...
-
Page 2: Table Of Contents
Everything TABLE OF CONTENTS You Need Step 1 - Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Overview - Honeycomb Motorization . -
Page 3: Step 1 - Getting Started
STEP 1 — GETTING STARTED OVERVIEW Motorizati on Parts & Tools Before you begin, check the accompanying diagram to make sure you have all the parts you need. You’ll need to make sure the surface you intend to install your hardware is sturdy enough to accommodate the brackets. If you’re screwing directly HEADRAIL MOLLY SELF DRILLING TOGGLE into a surface this means locati ng wood studs that are BOLT ANCHOR... -
Page 4: Step 2 - Brackets Installation
STEP 2 — BRACKET INSTALLATION STEP 2 — BRACKET INSTALLATION OUTSIDE MOUNT W/ SPACER BLOCK Spacer Blocks (Opti onal) Using the installati on bracket as a template, measure to the center of the Each spacer block projects brackets ⁄ ” bracket and mark the hole locati ons with away from mounti ng surface. - Page 5 STEP 3 — LINK 14 CHANNEL REMOTE STEP 3 — LINK 14 CHANNEL REMOTE 14 CHANNEL REMOTE 3. Press the SETTING button on the motor until the motor starts to beep. Important: Please read through this Release the button immediately after the section completely before beginning. CHANNEL beeps start. The motor will make 4 fast DISPLAY...
- Page 6 STEP 4 — SHADE INSTALLATION STEP 5 — OPERATION Shade Installati on 14 CHANNEL REMOTE CHANNEL DISPLAY Before mounting the head rail make sure Select the desired channel with the that the receiver wire is out of the head CHANNEL button. rail. For optimal performance, position Tapping the UP or DOWN buttons for the receiver wire so that it is facing into STOP/ less than 2 seconds will move the shade the room.
- Page 7 STEP 6 — ADJUST MOTOR LIMITS STEP 7 — SETTING LIMITS (if desired) Adjust Motor Limits LOWER LIMIT CHANNEL DISPLAY The lower and upper limits have been Hold the LIMIT button until the shade set at the factory. If you need to make starts beeping.
-
Page 8: Step 8 - Setting & Using A Favorite Position
STEP 8 — SETTING & USING A FAVORITE POSITION STEP 8 — SETTING & USING A FAVORITE POSITION Favorite Position Setting A Favorite Position If there is only a single shade on the Use the UP or DOWN buttons to channel proceed to setting favorites CHANNEL position the shade at the desired... -
Page 9: Step 9 - Advanced Programming
STEP 9 — ADVANCED PROGRAMMING STEP 9 — ADVANCED PROGRAMMING Replace Original Remote, Add Remove a Shade from a Remote Additional Remote or Add Shade or Channel and Link it to a CHANNEL to an Additional Channel Different Remote or Channel DISPLAY 1. Select the channel that you want to 1. Select the channel that you want... -
Page 10: Step 11 - Level The Bottom Rail
STEP 11 — LEVEL THE BOTTOM RAIL HOLD DOWN BRACKETS (IF NECESSARY) (OPTIONAL) Hold Down Brackets (Opti onal) Level the Bott om Rail (If Necessary) Optional hold down brackets are mounted with the supplied screws. Honeycomb shades use a system that ADJUSTMENT ADJUSTMENT SCREW SCREW allows easy leveling of the bottom rail. - Page 11 CHARGING THE MOTOR REMOVING THE SHADE Charging the Motor Removing the Shade When the shade begins to operate To remove a shade, insert a screwdriver slower than normal it is time to charge between the head rail and the bottom the motor.
-
Page 12: Solar Recharge Unit (Optional)
REPLACING THE BATTERY IN THE REMOTE SOLAR RECHARGE UNIT (OPTIONAL) Determine Solar Recharge Unit Replacing the Battery in the INSIDE MOUNT Placement Remote The solar recharge unit should be placed Remove the battery tray from the where is gets the maximum amount of remote by inserting a fingernail into the sunlight per day. In most cases this can indentation on the back of the remote. -
Page 13: Install Solar Recharge Unit
INSTALL SOLAR RECHARGE UNIT TROUBLESHOOTING Install Solar Recharge Unit PROBLEM SOLUTION Tape Method SOLAR PANEL RECHARGE UNIT The motor does not work Recharge motor Cut the tape (part # MI051045) to fit inside the white border as shown. Clean The motor continues to run in one The limit setting was unsuccessful the ends of the solar panel where the direction and needs to be reset tape will go with rubbing alcohol. When dry, remove the release liner from one The indicator light on the remote Replace the battery in the remote... -
Page 14: Safety
CARE & CLEANING NOTES Care & Cleaning The shade fabric is easy to care for. Regular dusting with a feather duster or vacuum cleaner brush is recommended. Most stains can be blotted with a damp sponge and mild detergent. Before using anything stronger than mild detergent and lukewarm water, test an unobtrusive corner of the shade. If you have any questions, call your dealer for advice. SAFETY Safety First. Style Second To None ™ Great style should never come at the cost of safety. Every Smith & Noble window treatment conforms strictly to today’s safety standards, including permanent ti e-down devices and built-in cord stops. To protect young children and pets, there’s no bett er way to eliminate risk than to use one of our motorized products. 25 smithandnoble.com 800 .248 .8888... -
Page 15: Warranty
Warranty Service The enjoyment of your window coverings should be everlasting, which is why our products come with a limited lifetime warranty. The warranty applies to the original owner, requires a proof of purchase and covers defects in material or craftsmanship. Shades or blinds must have been properly installed. We reserve the right to determine if your window covering warrants a repair or a replacement. In need of warranty service? Call us at 800.248.8888 and we’ll arrange for a repair or replacement ASAP. © 2019 Smith & Noble Home, Inc. All Rights Reserved SN082019...