Smith & Noble Honeycomb Shades Step By Step Installation Instructions

Top down/bottom up and day/night motorization

Advertisement

STEP BY STEP INSTALLATION INSTRUCTIONS
Honeycomb Shades
Top Down/Bott om Up
and Day/Night
Motorizati on

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Honeycomb Shades and is the answer not in the manual?

Questions and answers

Summary of Contents for Smith & Noble Honeycomb Shades

  • Page 1 STEP BY STEP INSTALLATION INSTRUCTIONS Honeycomb Shades Top Down/Bott om Up and Day/Night Motorizati on...
  • Page 2: Table Of Contents

    Everything TABLE OF CONTENTS You Need Step 1 - Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Overview - Honeycomb Motorization .
  • Page 3: Step 1 - Getting Started

    STEP 1 — GETTING STARTED OVERVIEW Motorizati on Parts & Tools Before you begin, check the accompanying diagram to make sure you have all the parts you need. You’ll need to make sure the surface you intend to install your hardware is sturdy enough to accommodate the brackets. If you’re screwing directly HEADRAIL MOLLY SELF DRILLING TOGGLE into a surface this means locati ng wood studs that are BOLT ANCHOR...
  • Page 4: Step 2 - Brackets Installation

    STEP 2 — BRACKET INSTALLATION STEP 2 — BRACKET INSTALLATION OUTSIDE MOUNT W/ SPACER BLOCK Spacer Blocks (Opti onal Using the installati on bracket as a template, measure to the center of the bracket and shades 36" or wider, required for 36" or under) mark the hole locati ons with a pencil for drilling .
  • Page 5: Step 3 - Shade Installation & Removal

    STEP 3 — SHADE INSTALLATION STEP 4 — LEVEL THE BOTTOM RAIL (IF NECESSARY) Shade Installation Level the Bottom Rail (If Necessary) Before mounting the head rail make sure that the receiver wire is out of the head Honeycomb shades use a system that ADJUSTMENT ADJUSTMENT SCREW SCREW rail. For optimal performance, position allows easy leveling of the bottom rail or the receiver wire so that it is facing into middle rail (no fabric on the top only, see the room.
  • Page 6: Hold Down Brackets (Optional)

    HOLD DOWN BRACKETS (OPTIONAL) Hold Down Brackets (Opti onal) Optional hold down brackets are Smith & Noble mounted with the supplied screws. With the shade at its proper drop, place the pin of each hold down into the hole in Smart Shades each end cap and mark the screw holes. Make sure the pins are level and aligned. Raise the shade, then screw the hold down bracket into the mounting surface. Operati ng & Programming Guide For Slightly flex the hold down brackets to HOLD DOWN insert the pins into the endcaps .
  • Page 7 PAIRING THE REMOTE PAIRING THE REMOTE For added protecti on, your remote control Select the channel that you want to arrived with a protecti ve fi lm on top. pair the shades to, using the CHANNEL Please remove this fi lm prior to use. selector butt on. CHANNEL DISPLAY Your shades will need to be paired to the Acti vate the Top Down/Bott om Up remote prior to operati ng your shade. See...
  • Page 8 OPERATING THE REMOTE UNPAIR THE REMOTE To unpair a shade(s) from a selected Select the desired channel with the channel, press and release the CONFIRM CHANNEL CHANNEL butt on. DISPLAY butt on on the back of the remote. CHANNEL Use the RAIL SELECTOR to choose DISPLAY Conti nue to press & release unti l the which rail you want to move. When a 1 shade jogs & beeps.
  • Page 9 SETTING SHADE LIMITS SETTING SHADE LIMITS Adjust Shade Limits (If Desired) Use the RAIL SELECTOR butt on to choose rail no . 1 . The lower and upper limits have been CHANNEL Hold the LIMIT butt on unti l the shade set at the factory. If you need to make DISPLAY beeps 4 ti mes.
  • Page 10 SETTING & USING A FAVORITE POSITION ADD OR REMOVE REMOTE OR CHANNEL If there is only a single shade on the channel CHANNEL Replace Original Remote, Add proceed to SETTING A FAVORITE POSITION DISPLAY Additi onal Remote or Add Shade to below. CHANNEL an Additi onal Channel DISPLAY If there is more than one shade on the channel, all shades on that channel will need 1 .
  • Page 11 ADD OR REMOVE REMOTE OR CHANNEL DE-ACTIVATE JOG FUNCTION To De-Acti vate the Jog Functi on Remove a Shade from a Remote or 1 . The remote comes pre-set with Channel and Pair it to a Diff erent CHANNEL jogging functi on acti vated. Follow the Remote or Channel DISPLAY directi ons below if you would like to...
  • Page 12 CHARGING SHADE SOLAR PANEL (OPTIONAL) Charging Shade Determine Solar Panel Placement When the shade begins to operate The solar panel should be placed where it gets the maximum amount of sunlight slower than normal it is ti me to charge the motor. Plug the 8.4v charger into the per day . wire. The charging wire is att ached to In most cases, this can be achieved by the back of the head rail.
  • Page 13: Solar Recharge Unit (Optional)

    INSTALL SOLAR PANEL INSTALL SOLAR PANEL Tape Method SOLAR PANEL RECHARGE UNIT Connect Solar Panel to Motor Cut the tape to fi t inside the white Aft er the shade is installed, plug the border as shown. Clean the ends of the solar unit into the motor recharge port.
  • Page 14: Troubleshooting

    TROUBLESHOOTING CARE & CLEANING Care & Cleaning PROBLEM SOLUTION The shade fabric is easy to care for. Regular dusting with a feather duster or vacuum cleaner Shade will not raise or lower. Recharge motor. brush is recommended. Most stains can be blotted with a damp sponge and mild detergent. Before using anything stronger than mild detergent and lukewarm water, test an unobtrusive Shade runs slowly. Recharge motor. corner of the shade. If you have any questions, call your dealer for advice. The motor continues to run in The limit setting was unsuccessful and one direction. needs to be reset. Channel Display screen on remote does Replace the battery in the remote not light up . (CR2430). The distance required to operate shade Replace the battery in the remote SAFETY with remote becomes shorter. (CR2430). Press the LIMIT button on the underside of the remote or the SETTING button on Shade goes up when down button is the wand and the STOP button at the pushed and down when up button is Safety First. Style Second To None...
  • Page 15: Warranty

    Warranty Service The enjoyment of your window coverings should be everlasting, which is why our products come with a limited lifetime warranty. The warranty applies to the original owner, requires a proof of purchase and covers defects in material or craftsmanship. Shades or blinds must have been properly installed. We reserve the right to determine if your window covering warrants a repair or a replacement. In need of warranty service? Call us at 800.248.8888 and we’ll arrange for a repair or replacement ASAP. © 2019 Smith & Noble Home, Inc. All Rights Reserved SN2061...

Table of Contents