STEP 1 — GETTING STARTED OVERVIEW Motorization - Waterfall shade Getting Started First, make sure you have all the parts and tools required to install your shades. MOUNTING BRACKETS ALL THE HARDWARE YOU’LL NEED: Pencil, screwdriver, ¼” nut driver, level, and a drill with a ⁄...
STEP 2 — MOUNTING THE BRACKETS STEP 2 — MOUNTING THE BRACKETS Outside Mount Inside Mount Center the shade over the window For as inside mount, hold the shade inside the window frame. Center the shade opening at the desired height. Mark the so the space between the end of the positi on of the ends of the headrail on the wall with a pencil.
Page 5
Smith & Noble Smart Shades Operati ng & Programming Guide For Rechargeable Motorized Shades Natural Woven Shades...
Page 6
PAIRING THE REMOTE OPERATING THE REMOTE Select the desired channel with the Your shades will need to be paired to CHANNEL button. the remote prior to operating your shade. CHANNEL See Pair the Remote below. DISPLAY Raise and Lower Shade CHANNEL Press the UP or DOWN buttons to DISPLAY...
Page 7
ADJUSTING SHADE LIMITS ADJUSTING SHADE LIMITS Lower Limit Adjust Shade Limits (If Desired 1. Press the DOWN button and let the The lower and upper limits have been shade go to the original lower limit. set at the factory. If you need to make adjustments to the limits, follow the 2.
Page 8
SETTING & USING A FAVORITE POSITION UNPAIR THE REMOTE If there is only a single shade on the channel proceed to SETTING FAVORITE POSITION below. Press the P2 button on the remote once. The shade will jog once and beep If there is more than one shade on once.
Page 9
DISABLING UNUSED CHANNELS ADJUSTING THE JOG FUNCTION When the jog function is activated, The 15 channel remote has the option tapping the UP or DOWN buttons for of turning off unused channels, making less than 2 seconds will move the CHANNEL channel selection easier.
Page 10
RESETTING FACTORY LIMITS RESETTING TO FACTORY MODE SHADE MOTOR WARINING: RESETTING TO FACTORY MODE WILL UNPAIR ALL PREVIOUSLY Resetting Factory Limits PAIRED CONTROLLERS AND WILL ERASE ALL PREVIOUSLY SET LIMITS. The motor must be put into limit setting mode to reset the factory limits. Resetting to Factory Mode Press the P2 button on the back of the Press and hold SETTING button on the motor for 14 seconds until the motor...
Page 11
SWITCHING DIRECTION / ADJUSTING SPEED CHARGING SHADE Switching Direction (Polarity When the shade begins to operate If the shade goes up when pressing slower than normal and beeps the DOWN button and down when CHANNEL CHARGER when operated it is ti me to charge pressing the UP button, the direction DISPLAY the batt ery.
Page 12
SOLAR PANEL INSTALL SOLAR PANEL (OPTIONAL) SOLAR PANEL RECHARGE UNIT Determine Solar Panel Placement Tape Method The solar panel should be placed where gets maximum Choose the locati on to mount the amount of sunlight per day. solar panel. most cases this be achieved by mounti ng the unit...
Page 13
INSTALL SOLAR PANEL SHORTCUTS Bracket Method Connect the sliding bracket and the L-shape bracket using screws and nuts. Do not overtighten to allow for easy adjustment to the solar panel mounting height needed. Ceiling mount the L-shape bracket to the window frame between the glass and the shade.
TROUBLESHOOTING CARE & CLEANING / SAFETY PROBLEM SOLUTION Care & Cleaning Shade will not raise or lower. Recharge motor. Occasional light vacuuming with a soft bristle attachment or gentle feather dusting is all Shade runs slowly. Recharge motor. that is required to keep your shades looking fresh and neat. The limit se ng was unsuccessful and The motor con nues to run in one direc on.
Warranty Service The enjoyment of your window coverings should be everlasting, which is why our products come with a limited lifetime warranty. The warranty applies to the original owner, requires a proof of purchase (hang on to your receipt!) and covers defects in material or craftsmanship.
Need help?
Do you have a question about the Natural Woven Shades and is the answer not in the manual?
Questions and answers