Related Manuals for Smith & Noble Luxe Linen Honeycomb Shades
Summary of Contents for Smith & Noble Luxe Linen Honeycomb Shades
- Page 1 Step by Step Installation Instructions Luxe Linen Honeycomb Shades Customer Service 800.248.8888 or visit us online at smithandnoble.com...
-
Page 2: Table Of Contents
Table of Contents Getting Started ....... . 3 Cordlift - . -
Page 3: Getting Started
Getting Started Standard + Top Down/Bottom Up Remove the shade from the packaging. Do not dispose of packaging HEADRAIL until the shade is operating to your satisfaction. Check the diagram to make sure you have all the parts indicated for the appropriate type of installation. -
Page 4: Cordlift - Standard & Top Down/Bottom Up
Attaching the Brackets Attaching the Brackets (con't) Cord Lift - Standard & Inside Mount Top Down/Bottom Up The brackets are mounted flat against Mounting 2½" the top sill surface. Bracket End brackets should be located ⁄ " ⁄ " ⁄ To fully recess the shade requires a flat with centerlines 2 "... -
Page 5: Attaching Extension Brackets
Operating the Shade Attaching Extension Brackets (Optional) Optional Extension Brackets To lower or release the shade, are used to project the back pull the cord inward toward the ⁄ of the shade up to 2 " from center of the shade. the mounting surface. -
Page 6: Cordless - Standard & Top Down/Bottom Up
Cordless Lift - Standard Top Down/ Bottom Up Standard Optional Optional Optional Mounting Bracket Extension Bracket Spacer Block Hold Down Bracket Parts of the Shade... -
Page 7: Attaching The Bracket
Attaching the Brackets Attaching the Brackets (con't) Shades are shipped with the required Outside Mount with Extension Use this number Shade widths 2” minimum number of brackets for proper of Brackets Bracket (optional) surface required Up to 40" installation. End brackets should be located approximately 3”... -
Page 8: Operating The Shade
Operating the Shade Troubleshooting Shade Will Not Stay Down: Fabric Billows Out When To lower the shade, pull down Shade Is Raised: on the handle which is secured The fabric may want to spring to the middle or bottom rail. up because it was fabricated Fabric can take a set when To raise the shade, push the... - Page 9 Loop Control - Standard, Top Down/Bottom Up & 2-on-1 Standard Optional Optional Optional Mounting Bracket Extension Bracket Spacer Block Hold Down Bracket Parts of the Shade...
-
Page 10: Attaching The Brackets
Attaching the Brackets Attaching the Brackets Shades are shipped with the required Use this number of Shade widths number of brackets for proper Brackets Outside Mount with Spacer installation. End brackets should be Up to 40" Block located approximately 3" from either 40"... -
Page 11: Hanging The Shade
Hanging the Shade Operating the Shade First, lower the middle and bottom rail Operate the shade by pulling down about an inch. This will help keep the on the side of the code. The front fabric from getting caught between the cord raises the shade, the rear cord lowers the shade. -
Page 12: Motorized Shades
o t o r i z e c o r o t a k p i n t o w i l l t r f t h e p e n P u s h d b a c e u p d o f S H A... -
Page 13: Attaching The Brackets
Attaching the Brackets Attaching the Brackets Extension Brackets Shades are shipped with the required Use this number of Shade widths (Optional). Use the top number of brackets for proper 2” minimum Brackets surface required installation. End brackets should be bracket holes. Up to 40"... -
Page 14: Hanging The Shade
Hanging the Shade Attaching the Battery (con't) Before mounting the headrail make Wall Attachment sure that the receiver wire is out of the headrail. For optimal performance, Using one (1) screw per clip, attach position the reciever wire so that it is the clips to the wall as shown. -
Page 15: Setting Up The Remote Control
Setting Up the Remote Control Setting Up the Remote Control (con't) Setting Favorites and Re-Adjusting Limits Re-adjusting Lower Limit (DOWN Shade Position) NOTE: When adjusting limits on a shade, unplug all other motorized shades. When completed 1) Press the DOWN directional button on Channel with adjusting limits, plug the motors back. -
Page 16: Hold Down Brackets (Optional)
Hold Down Brackets Care + Cleaning (optional) Optional Hold Down Brackets are Minimal care and cleaning is mounted with the supplied screws. needed to maintain the beauty of With the shade at its proper drop, your shades. place the pin of each Hold Down To Vacuum: Use brush or dust Bracket into the hole in each end head attachment. -
Page 17: Warranty
Warranty All Smith+Noble shades are designed for a lifetime of trouble-free use and is covered by a limited lifetime warranty. This warranty applies to the original customer/installation with proof of purchase and covers any defects in materials or workmanship provided that the product is measured and installed according to the product instructions.