Advertisement
Quick Links
Accessory Part No.
READ INSTALLATION INSTRUCTIONS THOROUGHLY BEFORE COMMENCING INSTALLATION.
PLACE THESE INSTRUCTIONS IN VEHICLE'S GLOVE BOX AFTER INSTALLATION IS COMPLETE
Care Instructions:
ISSUE 1: 25/08/2015
PARTS, SERVICE & ACCESSORIES
November 2015 Production Onwards
ACRYLIC HEADLAMP COVERS
Installation Instructions
PZQ14-42070
Do not slam bonnet.
Item
Component Name
1
Headlamp Cover Set
Top Metal Clip
Inner Bottom Metal Clip
Outer Bottom Metal Clip
Washer
2
Screw
Anti-Abrasive Tape
Alcohol Wipe
Installation Instruction
Accessory Part No. PZQ14-42070
RAV 4
Do not use automatic
car wash.
Qty
1
2
2
2
6
6
6
1
1
Installation Time: Approx. 15 mins
Do not use abrasive,
spirit or solvent
based cleaners.
Part number
PZQ14-42070
PZQ14-4207A
H4332
Clean with a mild
detergent and
water solution.
Page 1 of 7
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Toyota PZQ14-42070
Summary of Contents for Toyota PZQ14-42070
-
Page 1: Installation Instructions
Part number Item Component Name Headlamp Cover Set PZQ14-42070 Top Metal Clip Inner Bottom Metal Clip Outer Bottom Metal Clip Washer PZQ14-4207A Screw Anti-Abrasive Tape Alcohol Wipe Installation Instruction ISSUE 1: 25/08/2015 Accessory Part No. PZQ14-42070 Page 1 of 7... - Page 2 Screw PZQ14-8920A IMPREGNATED WITH 70% ISOPROPYL ALCOHOL Large Anti-Abrasive Tape Small Anti-Abrasive Tape Alcohol Wipe Installation Instruction ISSUE 1: 25/08/2015 Accessory Part No. PZQ14-42070 Page 1 of 7 FITTING KIT PZQ14-4207A HEADLAMP COVER PZQ14-42070 EXPLODED VIEW A EXPLODED VIEW B...
- Page 3 1-2cm off the headlamp surface. Adhere two thirds of the anti-abrasive tape directly below the slot onto the headlamp surface Remove Headlamp cover. See Dia #3. Diagram #: 3 ISSUE 1: 25/08/2015 Accessory Part No. PZQ14-42070 Page 3 of 7...
- Page 4 See Dia #5. Note: If clip is difficult to insert, carefully pry the bumper down using a plastic pry bar. Diagram #: 5 ISSUE 1: 25/08/2015 Accessory Part No. PZQ14-42070 Page 4 of 7...
- Page 5 See Dia #7. Diagram #: 7 8. Loosely secure the Headlamp Cover to the bottom metal clips with the screws and washers provided. See Dia #8. Diagram #: 8 ISSUE 1: 25/08/2015 Accessory Part No. PZQ14-42070 Page 5 of 7...
- Page 6 Ensure the screw is as close to the bottom of the Headlamp Torque: 0.5~0.8 NM Cover slot as possible. See Dia #11. Note: Ensure torque setting 0.5~0.8NM is used. Diagram #: 11 ISSUE 1: 25/08/2015 Accessory Part No. PZQ14-42070 Page 6 of 7...
- Page 7 Diagram #: 13 TO REMOVE: Reverse the above procedure. IMPORTANT: Conduct final inspection, ensuring all screws are tightened, and clips are correctly installed and not touching the headlamp surface. ISSUE 1: 25/08/2015 Accessory Part No. PZQ14-42070 Page 7 of 7...
Need help?
Do you have a question about the PZQ14-42070 and is the answer not in the manual?
Questions and answers