Full Gauge Controls MT-444E Faston Manual page 2

8. QUICK ACCESS MENU AND BASIC OPERATIONS
8.1. Quick Access Menu Map
You can navigate through the function menus by pressing the
details. The map of functions is shown below:
POWER-SAVING
MODE
;
LIGHT
;
DEFROST (ON/OFF)
;
CURRENT PROCESS DISPLAY
;
FUNCTIONS LOCK
;
CONTROL FUNCTIONS
SHUTDOWN
;
MIN. AND MAX.
ERASE MAX. AND MIN.
TEMPERATURE RECORD VALUES
;
8.2 Turning power-saving mode on/off
<
To switch power-saving mode on/off, press
This message will
be displayed
[ECO,]
Quick touch
8.3 Switch the light on/off
>
To switch the light on/off, press with quick touch or use the quick access menu (Item 8.1).
This message will
be displayed
[lamp]
Quick touch
8.4 Silencing the alarm
/
To silence the audible alarm, press the key (quick touch).
Quick touch
8.5 Manual Defrost
To start/stop a manual defrost, regardless of the schedule, press and hold the
[dEFr]message appears. Then release it. The [On,,] message will appear when it has started and
the [OFF,] message when it has been stopped. It can also be accessed through the quick access
menu (Item 8.1).
This message will
be displayed
[defr]
Press for 6 sec.
;
key (Flatec). See items below for further
EXIT THE FUNCTION
;
FUNCTION SELECTION
;
NUMBER OF TIMES THE
DOOR WAS OPENED
;
PRESET SELECTION
;
FAST FREEZING (ON/OFF)
;
VIEW TEMPERATURE
NO SENSOR S3 (CONDENSER)
;
DISPLAY SENSOR S2
TEMPERATURE (EVAPORATOR)
; ;
with quick touch or use the quick access menu (Item 8.1).
[On,,]
on
release
[Off,]
off
the key
[On,,]
on
release
[Off,]
the key
off
<
key for 6s, until the
[On,,]
on
release
[Off,]
the key off
8.6 Visualização da temperatura no sensor S2 (evaporador)
A temperatura no sensor S2 (evaporador) pode ser visualizada pressionando a tecla
até que apareça a mensagem [Sns2]. Caso este sensor esteja desabilitado, será exibida a
indicação[----].
Until this message
is displayed
[SnS2]
/
press
to confirm
Quick touch
8.7 Display process stage and current setpoint
To see which process stage is underway, press and hold the
appears. Then release it. The stage of the process which is in progress will be displayed, showing the
desired temperature (setpoint) in use, in relation to the current operating mode (normal/power-saving).It
can also be accessed through the quick access menu (Item 8.1).
This message will
be displayed
[Proc]
release
the key
Press for 4 sec.
IF F47=[OFF,]
Indication
F54
enabled
FAN-DELAY REFRIGERATION
F44 IF F24=0
MAX. F55 F25 F26 F27
IF F47=[On,]
Indication
IF F24=1
enabled
F29 F30 F31
REFRIGERATION
F44 IF F24=0
F25 F26 F27
8.8 Adjusting the desired temperature (setpoint)
To select the desired preset, press and hold the
then release it. The message [sp1] or [sp2] or [sp3] will be displayed depending on the currently
active preset and then the value for adjusting the normal setpoint of this preset.
change the value and press (1, 2 or 3) and press
This message will
This message will
be displayed
be displayed
[set,] [Sp1,]
[Sp2,]
release
the key
[Sp3,]
Press for 2 sec.
8.9 Change Preset
To select the desired preset, press and hold the
< >
then release it. Use the or keys to select the desired preset (1,2 or 3) and press
This message will
be displayed
[rec,]
Press for 4 sec.
Until this message Shows the temperature
is displayed of sensor 2 (evaporator)
[t-2,] [,,2. 0 ]
Ex:
>
key for 4s, until the[Proc]message
Indicates the temperature
Current stage
of the process
[dEL,] [t-2,]
Initial delay
([----]: if disabled)
[Fan,]
Fan delay
This message will
[rEFr]
Refrigeration
be displayed
[SP,,]
[Pre,]
Pre-defrost
([sp-e]: if it is in
[dEFr]
Defrost power-saving mode)
[dRAi]
Shows the current desired
Draining
temperature (setpoint)
Control
[----]
[,,2. 0 ]
Ex:
functions
switched off
IF F24=1 Lock indication if
F29 F30 F31 F34,F35,F36
enabled in F44
PRE-
DEFROST
DEFROST
F33 MAX. F41,F42,F43
Lock indication if
enabled in F44 F34,F35,F36
PRE-
DEFROST DRAINAGE
DEFROST
MAX. F41,F42,F43
F33
/
key for 2s, until the [Set,]message appears, and
Use the
/
to confirm.
Shows the current desired
temperature (setpoint)
[,,2. 0 ]
Use
< >
or
to select
the preset
/
key for 4s,until the [rEc,]. Message appears, and
Use
Preset
< >
[,,,1]
or
to select
[,,,2]
the preset
[,,,3]
;
(toque curto),
in S2
DRAINAGE
F46
F46
< >
or to
/
press
to confirm
/
to confirm.
/
press
to confirm