Advertisement
Quick Links
Advertisement
Related Manuals for Axis T26B
Summary of Contents for Axis T26B
- Page 1 Installation Instructions: T26B Installation Instructions Questions: Call 1 (855) ASK - AXIS...
- Page 2 You will be replacing this entire unit. You will need Allen Wrench to take phone cradles off of rail mounts. Save cradles, and place entire table (with rail) in back room. Questions: Call 1 (855) ASK - AXIS...
- Page 3 Parts List Cordless Screwdriver with Phillips Bit or Phillips Screwdriver Special Instructions (1) White Countertop Place countertop upside down on floor and screw in (6) Male RTA Fittings into pre-drilled holes. Male RTA Fitting Questions: Call 1 (855) ASK - AXIS...
- Page 4 Step 2- Screw (6) Male RTA Fittings into pre- drilled holes into the underside of countertop. Underside of countertop (3) Pre-drilled holes on each end for a total of 6. Screw in until tight (to top of thread). Questions: Call 1 (855) ASK - AXIS...
- Page 5 Female RTA Fitting *Note: When inserting Female RTA fittings, turn arrow towards material edge to receive the Male RTA Fitting when assembling. (2) Leg panels (L & R) Left panel shown here. Questions: Call 1 (855) ASK - AXIS...
- Page 6 (3 each panel). *Note: When inserting Female RTA fittings, turn arrow towards material edge to receive the Male RTA Fitting when assembling. Turn fitting so that arrow points toward edge of material. Questions: Call 1 (855) ASK - AXIS...
- Page 7 RTA Fittings into pre-drilled holes (2 on each end). Female RTA Fitting *Note: When inserting Female RTA fittings, turn arrow towards material edge to receive the Male RTA Fitting when assembling. (1) White Center Panel Questions: Call 1 (855) ASK - AXIS...
- Page 8 Step 4- Insert Female RTS Fittings into the larger pre-drilled holes at each end of the center panel (4 total). Turn fitting so that arrow points toward edge of material. display after covers are applied Questions: Call 1 (855) ASK - AXIS...
- Page 9 Installation Instructions: T26B Display Tools/Time Parts List Cordless Screwdriver with Phillips Bit or Phillips Screwdriver. Male RTA Fitting Special Instructions Screw in Male RTA Fittings into pre-drilled holes on leg panels (2 per leg panel) Questions: Call 1 (855) ASK - AXIS...
- Page 10 Installation Instructions: T26B Display Step 5- Insert Male RTS Fittings into the pre-drilled holes towards middle of each leg panel (4 total). Leg panel shown mounted to countertop underside here. Questions: Call 1 (855) ASK - AXIS...
- Page 11 RTA Fittings with phillips screwdriver. Make sure “bullnose” on leg panels faces towards front of of countertop (curved edge). Holes on sides of leg panels face inward, toward center. There is a Left and Right leg panel. Questions: Call 1 (855) ASK - AXIS...
- Page 12 RTA fittings AND the remaining (3) undercounter RTA fittings simultaneously. *May require 2 people. Once “sandwiched” between the leg panels and sitting on the counter underside correctly, tighten all RTA fittings with screwdriver. Questions: Call 1 (855) ASK - AXIS...
- Page 13 Installation Instructions: T26B Display Tools/Time Parts List Special Instructions Install Levelers (4) on leg panels. Once levelers are installed, flip unit right- Levelers (4) side-up onto it’s feet (requires 2 people). Questions: Call 1 (855) ASK - AXIS...
- Page 14 Flip unit over when complete. Screw levelers all the way down flush. Once all 4 levelers are installed, flip table back over on it’s feet. This will require 2 people. Questions: Call 1 (855) ASK - AXIS...
- Page 15 Installation Instructions: T26B Display Tools/Time Parts List Cordless Screwdriver with Phillips Bit or Phillips Screwdriver Riser (1) Special Instructions No.8 x 1/2” Pan Head Sheet Metal Screw (4) Riser Clamping Bracket (2) Questions: Call 1 (855) ASK - AXIS...
- Page 16 Installation Instructions: T26B Display Step 8- Using provided screws, attach ‘Riser Clamping Bracket’ to ‘Riser’ from underneath. See next page for more details. Screw riser clamping bracket to bottom of riser Questions: Call 1 (855) ASK - AXIS...
- Page 17 Align bracket holes with pre-drilled holes. 3) Note that threaded hole aligns over straight 4) Repeat for other bracket. Turn right-side-up and channel. place Riser into position. Questions: Call 1 (855) ASK - AXIS...
- Page 18 Installation Instructions: T26B Display Tools/Time Parts List Cordless Screwdriver with Phillips Bit or Phillips Screwdriver Large-Diameter Flat Washer (2) Special Instructions 1/4-20 x 1-1/4” Truss head Screw (2) Phillips head. Questions: Call 1 (855) ASK - AXIS...
- Page 19 1) Truss head screw through flat washer. 2) Insert up through straight (rear) channel into thread in bracket 3) Tighten with phillips scredriver. 4) Note screw being threaded up through bracket. Questions: Call 1 (855) ASK - AXIS...
- Page 20 Installation Instructions: T26B Display Tools/Time Parts List Tape measure Utility knife Straight edge Front Panel Graphic (1) Special Instructions Double-sided Tape Questions: Call 1 (855) ASK - AXIS...
- Page 21 5) 10b-Place foam tape pieces (provided) on 6) 10c-Align bottom of graphic with bottom of center the center panel (Not On Graphic –see illus). panel. Press down to adhere to foam tape Questions: Call 1 (855) ASK - AXIS...
- Page 22 Installation Instructions: T26B Display Reinstalling Cradle Mounts with New Adapters Tools/Time Parts List Wrench Allen Wrench Hex Bolt Rubber Washer Special Instructions Washer Adapter (Adapter Kit provides 5 of each per kit) Questions: Call 1 (855) ASK - AXIS...
- Page 23 8) Run wiring down through back 4 cradle mounts shown here–your store step 1) into new adapters and tighten channel to power/security. may vary. Position cradles to follow Allen Nut on the side. contour of riser front. Questions: Call 1 (855) ASK - AXIS...
- Page 24 Installation Instructions: T26B Display Step 12- Position table back against the wall/ mural. Upon successful completion of the T26B fixture, the display will look similar to the one shown here. Questions: Call 1 (855) ASK - AXIS...