Download Print this page
SolaX Power X3-Hybrid Series Quick Installation Manual

SolaX Power X3-Hybrid Series Quick Installation Manual

5-10kw
Hide thumbs Also See for X3-Hybrid Series:

Advertisement

Quick Links

Quick Installation Guide

X3-Hybrid 5kW-10kW
Packing List
Inverter X1
Bracket X1
Battery connectors
(positive X1, negative X1)
DC pin connectors
(positive X3, negative X3)
AC terminal X12
X3-Hybrid 5kW-10kW
User manual X1
Warranty card X1
Quick installation guide X1
EPS Connection(for E Version )
I
EPS wiring diagram
E Version
For AU/NZ
SolaX X3-Hybrid inverter
PV1+
PV1 -
PV2+
PV2 -
L1
L2
L3
N
L1
L2
L3
N
Main switch
SolaX meter
L1
L2
L3
N
PE
Changeover device with
interlocked switching
N-BAR
E-BAR
RCD
RCD
E
L1
L2
L3
N
E
L1
L2
L3
N
EPS
Loads
Loads
E Version
For Other Countries
PV1+
SolaX X3-Hybrid inverter
PV1 -
PV2+
PV2 -
L1
L2
L3
N
L1
L2
L3
N PE
Main switch
SolaX meter
L1
L2
L3
N
PE
RCD
RCD
E-BAR
E
L1
L2
L3
N
E
L1
L2
L3
N
EPS
Loads
Loads
This function can be achieved manually or automatically according to
user's preference.
For manual solution, please install an external switch.
DC connectors
Expansion bolt X5
(positive X3, negative X3)
Ring terminal X2
NTC X1
Grounding nut X1
Set screw(for mounting) X2
Wifi module(optional) X1
Smart Plug(optional) X1
EPS connection steps:
1. Make wire(EPS cable size: refer to table 2)
the cable is not
12mm
L 1
required for
L 2
L 3
Australia
N
60mm
For Australia/New Zealand
+
-
12mm
L 1
L 2
L 3
N
P E
60mm
Battery
For other countries
table2: Cable and Micro-breaker recommended
X3-Hybrid-5.0-D
X3-Hybrid-6.0-D
X3-Hybrid-8.0-D
Model
X3-Hybrid-5.0-N
X3-Hybrid-6.0-N
X3-Hybrid-8.0-N
EPS Cable
≥5mm²
≥5mm²
≥5mm²
EPS breaker
25A
25A
2. Insert EPS cable into EPS port through screw cap.
+
-
Battery
DPDT
Australia/New Zealand
other countries
Note: The right most port
Note: ConnectPEwire into
should not be connected !
PE port at right !
-Mark position of five holes.
- Screw the expansion screws.
PVconnectionsteps
positive DC
pin contact
7 mm
negative DC
pin contact
cable
8 pin terminal X1
7 mm
AC connectionsteps(AC cable size:refer to table1):
Scope tape X1
1.Remove thetop-down cover.
3.Insert AC cable into Grid port
through screw cap.
Lithium Battery Connection
Battery connection diagram
Nonpolarized
DC breaker
Power connection
-
high-voltage lithium battery.
X3-Hybrid-10.0-D
X3-Hybrid-10.0-N
≥5mm²
32A
32A
A:Power Connection Steps:
B:Communication Connection Steps:
PE
Step1: Disassemble the BMS cable gland.
Step2: Prepare a communication
cable(without sheath)and insert
the communication cable through
the cable nut.
Mounting Steps
- Drill holes with φ10 drill.
- Depth: at least 60mm.
- Match the inverter with the bracket.
- Screw the cross recessed screw on the bracket.
PV and AC Connection
:
(PV cable size:12AWG)
male plug
tight nut
clamp contact
nut
female plug
12mm
L 1
L 2
L 3
N
P E
60mm
2. Make AC wires.
4. Connect the wire to the AC terminal in the inverter. 
X3-Hybrid-5.0-D
X3-Hybrid-6.0-D
X3-Hybrid-8.0-D
Model
X3-Hybrid-5.0-N
X3-Hybrid-6.0-N
X3-Hybrid-8.0-N
Cable
4-5mm²
4-5mm²
4-5mm²
Micro-breaker
20A
20A
25A
table1
Note: For lead-acid battery connection, please refer to Important Instruction for lead acid battery.
Battery breaker
Before connecting to battey, please install a nonpolarized DC breaker to make
sure inverter can be securely disconnected during maintanance.
X3-Hybrid-5.0-D
Model
X3-Hybrid-5.0-N
Voltage
Current[A]
BMS PIN De nition
Communication connection
Communication interface bewteen inverter and battery is CAN with a RJ45
connector.
PIN
1
2
Definition
NTC
GND
+
CAN
Note:
The battery communication can only work when the battery BMS iscompatible
withtheinverter.
Press down spring until it clicks audibly into place
wire strands
The ne wire strands must be seen in the champer
Step3: Assemble the cable gland and
screw the cable nut.
- Tighten the expansion tubes.
-Align the halves connectors
Overview of PV connection
a.L-wire,N-wire connection
b.PE wire connection
X3-Hybrid-10.0-D
X3-Hybrid-10.0-N
5-6mm²
32A
(optional)
X3-Hybrid-6.0-D
X3-Hybrid-8.0-D
X3-Hybrid-10.0-D
X3-Hybrid-6.0-N
X3-Hybrid-8.0-N
X3-Hybrid-10.0-N
Nominal voltage of DC breaker should be larger than maximum
voltage of battery.
32A
3
4
5
6
7
8
BMS_CANH
BMS_CANL
BMS_485A BMS_485B
GND
GND

Advertisement

loading
Need help?

Need help?

Do you have a question about the X3-Hybrid Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for SolaX Power X3-Hybrid Series

  • Page 1: Quick Installation Guide

    Mounting Steps -Mark position of five holes. - Drill holes with φ10 drill. - Tighten the expansion tubes. - Depth: at least 60mm. Quick Installation Guide X3-Hybrid 5kW-10kW - Match the inverter with the bracket. - Screw the expansion screws. - Screw the cross recessed screw on the bracket.
  • Page 2 Meter Connection Earth Connection&Start Inverter Meter connection diagram 485A 485B Meter connection step To inverter-L To inverter-N Earth Connection Steps(mandatory): 1) Insert L/N wires and the 485cable Cable size: 12AWG. into the meter. 7 11 To grid-L To grid-N 2) Insertthe other side of the cable into the meter port on the ring terminal inverter.

This manual is also suitable for:

X3-hybrid-6.0-dX3-hybrid-6.0-nX3-hybrid-8.0-dX3-hybrid-8.0-nX3-hybrid-10.0-dX3-hybrid-10.0-n ... Show all