Renesas PORTER R-CarM2 Setup Manual
  1. Manuals
  2. Brands
  3. Renesas Manuals
  4. Motherboard
  5. PORTER R-CarM2
  6. Setup manual
Renesas PORTER R-CarM2 Setup Manual

Renesas PORTER R-CarM2 Setup Manual

System evaluation board
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
[Preliminary] R-CarM2 System Evaluation Board PORTER Rev.B Setup Manual Rev.0.01
R-CarM2 System Evaluation Board
RTP0RC7791LCB00010S (PORTER Rev.B)
Setup Manual
Rev.0.01
Feb 2015
Renesas Electronics Corp.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PORTER R-CarM2 and is the answer not in the manual?

Questions and answers

Related Manuals for Renesas PORTER R-CarM2

Summary of Contents for Renesas PORTER R-CarM2

  • Page 1 [Preliminary] R-CarM2 System Evaluation Board PORTER Rev.B Setup Manual Rev.0.01 R-CarM2 System Evaluation Board RTP0RC7791LCB00010S (PORTER Rev.B) Setup Manual Rev.0.01 Feb 2015 Renesas Electronics Corp.

  • Page 2: Revision History

    [Preliminary] R-CarM2 System Evaluation Board PORTER Rev.B Setup Manual Rev.0.01 Revision History Date Revision Description Feb 2015 0.01 Released. Feb 2015 Renesas Electronics Corp.

  • Page 3: Table Of Contents

    SW26 (Board Power-Supply Circuit Control) Specifications ............... 10 2.4. Appendix (Resister installation option) ..................... 11 2.4.1. DDR1600 => DDR1333 mode ......................11 2.4.2. R-CarM2W => R-CarM2N ........................11 2.4.3. Non Secure mode => Secure mode ....................... 11 Feb 2015 Renesas Electronics Corp.
  • Page 4 [Preliminary] R-CarM2 System Evaluation Board PORTER Rev.B Setup Manual Rev.0.01 Table Numbers Table 2.1.1 Initial Setting of Jumper Switches ....................6 Table 2.2.1 System Reset Switch ......................... 10 Table 2.3.1 Accessory Power-Supply Switch ..................... 10 Feb 2015 Renesas Electronics Corp.
  • Page 5 Figure 1.1.3 Locations of Switches on the PORTER(REV.B) Board (Bottom Side) ........2 Figure 2.1.1 JP1 Settings ............................7 Figure 2.2.1 SW9 System Reset Switch ......................10 Figure 2.3.1 SW26 Accessory Power-Supply Switch ..................10 Feb 2015 Renesas Electronics Corp.

  • Page 6: Introduction

    JTAG microSD Sot ch2 (back side) CN23 EXIO_A (back side) CN18 SW26 CN21 EXIO PWR CN25 Debug Console ACC Switch CPUFAN PWR POWER IN (SCIF0) (+12V) Figure 1.1.1 Location of Connectors on the PORTER(REV.B) Board Feb 2015 Renesas Electronics Corp.

  • Page 7: Location Of Switches And Jumper On The Porter(Rev.b) Board

    Location of Switches and Jumper on the PORTER(REV.B) Board JP10 JP11 JP12 SW18 Figure 1.1.2 Location of Switches on the PORTER(REV.B) Board (Top Side) NO Switches on Bottom Side Figure 1.1.3 Locations of Switches on the PORTER(REV.B) Board (Bottom Side) Feb 2015 Renesas Electronics Corp.

  • Page 8: Quick Setup Of The Porter(Rev.b) Board

    The PORTER(REV.B) board is activated and the following message is displayed on the screen of the terminal emulation software. KOELSCH SPI_LOADER(DDR3L_1333) V0.16a 2014.10.03 DEVICE S25FL512 U-Boot 2013.01.01-gc4d5d6e (Nov 13 2014 - 17:21:53) CPU: Renesas Electronics R8A7791 rev 2.0 Board: Porter Board DRAM: 1 GiB MMC: sh-sdhi: 0, sh-sdhi: 1, sh-sdhi: 2...
  • Page 9 Alternatively, the board can be booted through the QSPI interface by shorting the JP8 jumper as described in Section 2.1.8. When booting with the QSPI flash, the screen should look similar to the one below. U-Boot 2013.01.01-g0308ea0-dirty (Jan 09 2015 - 20:09:53) CPU: Renesas Electronics R8A7791 rev 2.0 Board: Porter Board DRAM: 1 GiB...

  • Page 10: Precautions

    In evaluation of the MLB, HSCIF1, and so on (evaluation which entails data output from the peripheral devices) with the PORTER(REV.B) board, be sure to change the settings for pin function control beforehand in order to avoid collision of the R-CarM2 and output signals. Feb 2015 Renesas Electronics Corp.

  • Page 11: Switch Settings

    3.3K pullup to 3.3v JP11 Color Resolution Floating JP12 Only for use with AVB extension board Settings Switch Switch Switch Number Name Surface (ON) (OFF) SW18 Address ALL OFF -> Address lines reserved for QSPI Feb 2015 Renesas Electronics Corp.

  • Page 12: Jp1 (Trst#) Specifications

    Connects the SSI_SDATA1 pin of the R-CarM2 to the I2S1 pin (pin 6) of the ADV7511W (U44). • [2-3] short Sets the SSI_SDATA1 pin of the R-CarM2 to output. • N.C. Setting Inhibited (No Connect) • Feb 2015 Renesas Electronics Corp.

  • Page 13: Jp4 (Can Termination Selection) Specifications

    JP8 selects whether to boot from the QSPI flash chip or the NOR flash chip. The following shows the initial setting at shipment. [JP8] Function: EtherAVB Clock Selection Short Boot from NOR flash Open Boot from QSPI flash Figure 2.1.5 JP8 Settings Feb 2015 Renesas Electronics Corp.

  • Page 14: Jp9 (Debug Mode Selection) Specifications

    [JP11] FRC/Color Resolution Selection Function: 1-2 short 8bit Resolution (16,777,216 colors) (‘H’) 1 8bit Resolution JP11 2-3 short 6bit Resolution (262,144 colors) (‘L’) Open Not specified 3 6bit Resolution Figure 2.1.8 JP11 Settings Feb 2015 Renesas Electronics Corp.

  • Page 15: Push-Switch Specifications

    Turns on the PORTER(REV.B) board accessory power. As a result, the power-supply voltage is supplied of ’OFF’ to the system. marking When the switch is ‘ON,’ the switching regulator (such as U576: IR3838MPbF) starts generating the power. Feb 2015 Renesas Electronics Corp.

  • Page 16: Appendix (Resister Installation Option)

    Install R560(10k) for ‘R-CarM2N’. Remove R560(10k) for ‘R-CarM2W’. 2.4.3. Non Secure mode => Secure mode MD5=’L’ … Secure mode MD5=’H’… Non Secure mode (default) Procedure) Install R616(10k) for ‘Secure mode’. Remove R616(10k) for ‘Non Secure mode’. Feb 2015 Renesas Electronics Corp.

Table of Contents