Related Manuals for OneVue OneVue Sense E121
Summary of Contents for OneVue OneVue Sense E121
- Page 1 OneVue™ Sense Water Leak Sensor Installation Guide Product Models: E121, E123 09/25/19...
- Page 2 Primex. OneVue is a trademark of Primex. All other trademarks are the property of their respective owners. The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Primex, Inc.
-
Page 3: Table Of Contents
Step 3: Mount Water Leak Sensor .................... 14 Step 4: Place Water Detector ....................15 Step 5: Establish connections ....................16 Step 6: Verify connection to OneVue ..................16 Step 7: Verify OneVue settings ....................16 Step 8: Test water detection ....................17 OneVue Network Requirements ....................... -
Page 4: Water Leak Sensor Application Uses
Water Leak Sensor application uses The OneVue Water Leak Sensor is designed to support a wide range of applications and placement options. Application uses Monitor areas to prevent serious interruptions to your facility's systems or a loss of assets. • HVAC and Electrical Rooms •... - Page 5 Water Leak Sensor Page 5...
-
Page 6: Water Leak Sensor And Water Detector Specifications
• Data Packet Size: typically less than 5 kilobytes (kB) Power over Ethernet (PoE) and Ethernet supported specifications Applies to: OneVue Temperature Sensor, Differential Pressure Sensor, Water Leak Sensor, Contact Closure Sensor, OneVue Sync Transmitters, OneVue Bluetooth Bridge, OneVue Bell Controller •... -
Page 7: Water Detector Specifications
Enclosure Enclosure: ABS plastic Dimension: 4.7" H x 3.7" W x 1.3" D (11.93cm x 9.39cm x 3.30cm) Weight: 0.3 lb (136 gram) with 2 AA Lithium batteries Display: Liquid crystal display (LCD), HTN reflective glass, dimension: 0.75" H x 1.38" W (1.90 cm x 3.50 cm) LCD Display: current sampled reading and operating status LED Status Indicator Water Detector input: USB Mini B (5 pin) connector... - Page 8 If the unit’s metal contacts come into contact with a foreign material (oil, detergent, etc.), then contacts may repel water and therefore will not be able to properly detect water. • Water Detector is water-resistant, but is not waterproof. If the detector has been submerged in water or becomes wet for an extended period of time, test the unit to verify water detection.
-
Page 9: Water Leak Sensor Device Features
Segment Description Signal OK Indicates its last check-in to OneVue was successful. No Signal Indicates the last check-in to OneVue failed. For wireless network use, a failed check-in may be due to the device is not within range of its configured wireless access point or the wireless signal strength is not adequate for normal operation. -
Page 10: Service Buttons
OneVue. During a check-in, all logged in button readings are transmitted to OneVue and any pending updates are downloaded to the device. During an active check-in connection, additional pressing of the check-in button is ignored. -
Page 11: Water Detector
State/Status Device power Yellow LED flashing Warning state AC or PoE power: LED illuminated and flashes Refer to the LCD display to identify the condition • Low battery • Unresponsive Red LED flashing Reading Alarm All power methods: LED illuminated and flashing •... -
Page 12: Install Water Leak Sensor And Water Detector
Install Water Leak Sensor and Water Detector Supplied components Inspect the package contents to verify the supplied components are present and no damage has occurred during shipping. Quantity Component Water Leak Sensor Water Detector AC power adapter: 5V DC USB Mini B (5 pin) connector interface, 5 ft (1.5 m) cable, Input: 100-240 VAC, 50/60 Hz, 0.4A, Output: 5V DC, 1.0A max Primex 3.0v Lithium/Iron Disulfide Battery Pack (contains 2 AA 1.5V Energizer®... -
Page 13: Step 1: Verify Sensor Configuration
• To prevent damage to the Water Detector components the input plug should remain in place while not in use. Step 1: Verify sensor configuration Prior to installation, a sensor device must be configured for use with OneVue. A sensor is either configured prior to shipment through Device Preconfiguration or onsite using the OWDC app. -
Page 14: Step 2: Insert Batteries And Turn On Battery Backup Power
Step 2: Insert batteries and turn on battery backup power 1. Remove device cover; simultaneously press the two tabs located on the top side of the device (A). 2. Insert the 3.0v Primex Lithium/Iron Disulfide Battery Pack or two 1.5v Lithium AA batteries. Follow the symbols showing the correct way to position the positive (+) and negative (-) ends of the battery pack. -
Page 15: Step 4: Place Water Detector
Method Steps Wall mount Key-hole mount (A) Determine the mounting location by referencing the key-hole slot located on the back of the device. Pre-drill mounting hole into the wall surface and insert wall anchor. Insert a wall anchor into mounting hole. Insert a #6 drywall screw into the wall anchor, leaving approximately 3/8 in. -
Page 16: Step 5: Establish Connections
Connect Water Detector to sensor device (B). Step 6: Verify connection to OneVue A Water Leak Sensor does not monitor for water until it has connected to OneVue. Verify Signal OK is displayed on the LCD screen, which indicates it successfully checked-in. When power was applied, the sensor initiated a check-in to OneVue. -
Page 17: Step 8: Test Water Detection
By default, set to 0 (zero). A Wet reading automatically results in an Alarm state. The Alarm Delay is the amount of time OneVue delays setting the sensor and Monitored Asset to an Alarm state when in an Out of Range status. When it remains in an Out of Range for time period set in its Alarm Delay setting, the sensor and its Monitored Asset are set to an Alarm state with a status of Out of Range, Past Alarm Delay. -
Page 18: Onevue Network Requirements
Primex Ethernet, PoE, and Wi-Fi enabled devices communicate to OneVue over your facility’s network using the Hypertext Transfer Protocol Secure (HTTPS) protocol. OneVue client and device data is encrypted in transmit and all sensitive data is encrypted at rest. An outbound HTTPS connection is established by each device and once complete the IP address is released. - Page 19 Domains and URLs. The files downloaded include the Sync device clock list, Notify device schedules, and device setting updates. OneVue is a high-availability (HA) platform that may change IP addresses at anytime, therefore OneVue does not support the use of firewall IP address filtering.
-
Page 20: Safety, Regulatory, Warranty
Safety, Regulatory, Warranty The following applies to a OneVue Sense models T101, T102, A120, A100, E121, E122, E123. SAFETY PRECAUTIONS READ THIS DOCUMENT THOROUGHLY BEFORE PERFORMING INSTALLATION OR SERVICE PROCEDURES. Safety Precautions • Device is designed for indoor use only and is not weather protected. Operating a device outdoors or in wet areas is an electrical hazard and may damage the device while nullifying its warranty. - Page 21 To assure continued appliance, any changes or modifications not expressly approved by the party responsible for compliance could voice the user's authority to operate this equipment. (Example -use only shielded interface cables when connecting to computer or peripheral devices). FCC Warning Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
-
Page 22: Primex One Year Limited Warranty
PRIMEX ONE YEAR LIMITED WARRANTY Warranty applies to: Sense models T101, T102, A120, A100, E121, E122, E123, LD100STRD, MSW1, SMRTGRP, T100, Notify Bell Controller E130 Primex, Inc. warrants this product to be free from defects in materials and workmanship for a standard of one (1) year from the date of purchase. -
Page 23: Technical Support
Technical Support You may require technical support when you have questions about product features, installation and configuration, or troubleshooting. Support services are delivered in accordance with your organization's support agreement, end user licenses agreements, and warranties, either with a Primex Certified Sales and Service Partner or directly with Primex. Support through Primex Certified Sales and Service Partners Ensuring our customers experience excellent service is of utmost importance to Primex.