Table of Contents
Advertisement
Quick Links
INSTALLATION AND SERVICE MANUAL
SUBMERSIBLE
SOLIDS HANDLING
PUMP
HYDROMATIC
NOTE! To the installer: Please make sure you provide this manual to the owner of the equip ment or to the responsible
party who maintains the system.
Item # E-03-554 | Part # 5625-554-1 | © 2018 Pentair plc | 09/05/18
ENGLISH: PAGES 2-12
Installation and Service Manual
For use with product built with Marathon®
motor.
NOTE! To the installer: Please make sure you provide
this manual to the owner of the equip ment or to the
responsible party who maintains the system.
(*Hazardous Location
Motor End)
(S3RX Only)
Models
S3R(X
*Used in Hazardous Locations Class I,
Division 1, Groups C and D
)
*
Advertisement
Table of Contents
Related Manuals for Pentair Hydromatic S3R
Summary of Contents for Pentair Hydromatic S3R
- Page 1 INSTALLATION AND SERVICE MANUAL Models SUBMERSIBLE S3R(X *Used in Hazardous Locations Class I, Division 1, Groups C and D SOLIDS HANDLING PUMP ENGLISH: PAGES 2-12 Installation and Service Manual For use with product built with Marathon® motor. NOTE! To the installer: Please make sure you provide this manual to the owner of the equip ment or to the responsible party who maintains the system.
-
Page 2: Safety Warnings
Safety Warnings When using the cord and plug, plug rotated (6 revolutions) after setting into a grounded outlet only. When nonop er a tion al for 3 months or wiring to a system control, connect longer and prior to electrical Before Installation: the pump ground lead to the start-up. - Page 3 However, some engineers set for turn-on for two pumps. The S3R submersible pump is sup- prefer to have the alarm level set Pumps alternate op er a tion on each plied for 1 and 3 phase and for 200, be low the override level as it is successive cycle.
- Page 4 Pump Installations made. An ohm me ter or Megger can IMPORTANT: If equipment is not be used to check wire continuity. properly wired and pro tect ed as recommended, the warranty is void. Installing Pump in Sump: Installing Switch Controls: Before installing pump in sump, lay Caution: The 230 volt 3 phase pump The controls are supported by a it on side and turn impeller manually.
-
Page 5: Pump Operations
sump to fill to the override shows satisfactory operation. required), the cord cap should be re- control level. attached reversing the steps above. If seal failure is not used, the pump Ensure the o-ring is in place and 7. Turn both switches to Auto should be lifted once every two years perform a hi-pot test for safety once and the oil drained from the seal... - Page 6 at an authorized Hydromatic service CAUTION: Do not reconnect 3. After chamber is drained, center. Charges will not be allowed pow er to a cord and cap assembly remove hold-down bolts and if (in war ran ty) pump is not taken to while removing from the pump.
- Page 7 ® IMPORTANT: Use only com pres- only Hydromatic submersible IMPORTANT: The impeller is sion type insulated connectors on oil in this chamber or high designed to be self-tightening when the wires. running so impeller may be difficult grade transform er oil. to break loose.
-
Page 8: Pump Troubleshooting
2. Lower float control may be of liquid due to a failed level hung-up in the closed position. ® control. All Hydromatic Check in sump to be sure con- S3R sub mers ible motors trol is free. can operate for extended periods out of water without... -
Page 9: Wiring Diagrams
Wiring Diagrams... - Page 10 S3R Parts List For use with product built with Marathon motor. ® Ref. Part Part Ref. Part Part Description Qty. Description Qty. Wire Connector (230V 3 f Only) 008530001 001500231 O-ring 005570001 Wire Connector (460/3/60) 054540011 Spring Pin 005570001 Wire Connector (200/230/1/60 & 200/575/3/60) 049160001 Seal (Ceramic) Std.
- Page 11 S3RX Parts List For use with product built with Marathon motor. ® Ref. Part Part Ref. Part Part Description Qty. Description Qty. 152730355 35' Cord Assembly 14-4 007400175 Rotor & Shaft 2 HP 1 ph. 1750 152730345 35' Cord Assembly 12-4 077730145 Rotor &...
- Page 12 Pentair Hydromatic will cover only the lower seal and labor thereof for all dual seal pumps. Under no circumstance will Pentair Hydromatic be responsible for the cost of field labor, travel expenses, rented equipment, removal/reinstallation costs or freight expenses to and from the factory or an authorized Pentair Hydromatic service facility.