Related Manuals for Pentair Hydromatic C4S(X)P Series
Summary of Contents for Pentair Hydromatic C4S(X)P Series
- Page 1 SUBMERSIBLE SOLIDS HANDLING PUMP C4S(X H3H(X H4H(X S4M(X S4P(X S4HV(X S4MV(X *Used in Hazardous Locations Class I, Division I, Groups C & D): FM INSTALLATION AND OPERATION MANUAL pentair.com...
-
Page 2: Table Of Contents
TABLE OF CONTENTS: SECTION ........................................PAGE General Information ....................................3-4 Pump Installation ...................................... 5 Pump Operation & Maintenance ................................6-7 Parts List ........................................8 Hydraulic Ends Part List ................................... 9 Motor Parts Group ....................................10 Impeller Parts List ....................................10-11 Wiring Diagrams ......................................12 Warranty ........................................13... -
Page 3: General Information
GENERAL INFORMATION READ AND FOLLOW SAFETY INSTRUCTIONS! ELECTRICAL SAFETY ELECTROCUTION HAZARD: Must be installed by This is the safety alert symbol. When you see this symbol a qualified professional. First disconnect all electrical power on your pump or in this manual, look for one of the following before attempting service. - Page 4 GENERAL INFORMATION the starter in the panel breaks power to the pump. This manual contains important information for the safe use of this product. Read completely and do not throw away. Once the sensor resets, the starter is automatically reset for FM for continued operation of the pump.
-
Page 5: Pump Installation
PUMP INSTALLATION INSTALLING PUMP IN SUMP For record keeping purposes, we suggest the pump be marked Before installing the pump in the sump, lay it on its side and rotate externally with the new voltage and qualified personnel that impeller. Impeller may be slightly stuck due to factory test water. performed the change. -
Page 6: Pump Operation & Maintenance
Any pump that is in warranty must be returned to the factory for Double check all wire connections. service or repaired at an authorized Pentair Hydromatic service center. Charges will not be allowed if (in warranty) pump is not Turn pumps to Off position on H-O-A switches. - Page 7 TROUBLESHOOTING Pump does not deliver proper capacity. Pump Troubleshooting Discharge gate valve may be partially closed or partially Below is a list of common problems and the probable causes: clogged. Pump will not start. No power to the motor. Check for blown fuse or open circuit Check valve may be partially clogged.
-
Page 8: Parts List
PUMP PARTS LIST C4S(X)P, H3H(X)P, H4H(X)P, S4M(X)P, S4P(X)P, S4HV(X)P and S4MV(X)P For use with product built with Premium Efficient motor. 3, 4 Ref.No. Part No. Part Description Qty. Ref.No. Part No. Part Description Qty. 28010D000 MOTOR HOUSING 19103A048 CAPSCREW – S4M(X)P, S4MV(X)P, S4HV(X)P 27818D010 BEARING HOUSING CAPSCREW –... -
Page 9: Hydraulic Ends Part List
HYDRAULIC ENDS PART LIST S4M(X)P S4MV(X)P D6 D5 S4P(X)P H3H(X)P D10 D8 D9 D12 D11 D13 S4HV(X)P C4S(X)P D5 D6 H4H(X)P Item No. Description S4M(X)P S4MV(X)P S4HV(X)P S4P(X)P H3H(X)P H4H(X)P C4S(X)P O-RING 001500581 001500581 001500581 05876A136 05876A136 05876A136 05876A136 IMPELLER KEY 083460033 083460011 083460011... -
Page 10: Motor Parts Group
MOTOR PARTS GROUP 10 – 15 hp 10 – 15 hp 10 – 15 hp 7.5 hp 7.5 hp 7.5 hp Item 2-Pole 3450 RPM 208-230/3/60 460/3/60 575/3/60 208-230/3/60 460/3/60 575/3/60 STATOR 27889D003 27889D003 27889D603 27887D003 27887D003 27887D603 ROTOR/SHAFT 27887D011 27887D011 27887D011 27887D011... -
Page 11: Impeller Parts List
IMPELLER PARTS LIST S4M(X)P S4HV(X)P Description Voltage/PH Cord Trim Impeller Description Voltage/PH Cord Trim Impeller 1750 RPM 3450 RPM S4M(X)P500BC 208/1 6.75 070710312 S4HV(X)P750DD 208/3 4.63 082130172 S4M(X)P500CC 230/1 6.75 070710312 S4HV(X)P750ED 230/3 4.63 082130172 S4M(X)P500DC 208/3 10-4 6.75 070710312 S4HV(X)P750FD 460/3 10-4... -
Page 12: Wiring Diagrams
WIRING DIAGRAMS 1 PHASE BLACK, WHITE, AND RED MOTOR LEADS CAN ONLY BE CONNECTED TO PANEL TERMINAL BLOCKS AS SHOWN ON SCHEMATIC. INCORRECT CONNECTION CAN CAUSE DAMAGE TO PUMP AND/OR PANEL COMPONENTS THREE PHASE OVERLOAD RELAY MUST BE CLASS 1O TRIP & AMBIENT COMPENSATED & CONNECTED IN THE “DAISY CHAIN”... -
Page 13: Warranty
Pentair Hydromatic authorized control panels are used. All seal fail and heat sensing devices must be hooked up, functional and monitored or this warranty will be void. Pentair Hydromatic will cover only the lower seal and labor thereof for all dual seal pumps. - Page 14 NOTES E-03-577 (01-23-20)
- Page 15 NOTES E-03-577 (01-23-20)
- Page 16 1101 Myers Parkway | Ashland, OH 44805 | Ph: 855-274-8947 | Orders Fax: 419-281-4087 | pentair.com/hydromatic For a detailed list of where Pentair trademarks are registered, please visit www.pentair.com/en/registrations.html. Pentair trademarks and logos are owned by Pentair PLC. or its affiliates. Third party registered and unregistered trademarks and logos are the property of their respective owners. Because we are continuously improving our products and services, Pentair reserves the right to change specifications without prior notice.