Related Manuals for Pentair Hydromatic HPS4SDX
Summary of Contents for Pentair Hydromatic HPS4SDX
- Page 1 SUBMERSIBLE SOLIDS HANDLING PUMP HPS4SD(X) HPS4HD (X) HPS6MD(X) INSTALLATION & OPERATION MANUAL pentair.com ©2022 Pentair. All Rights Reserved.
-
Page 2: Table Of Contents
TABLE OF CONTENTS SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 SPECIFICATIONS . - Page 3 PAGE INTENTIONALLY LEFT BLANK E-03-601 (02-15-22)
- Page 4 SAFETY INFORMATION SAFETY SYMBOLS GENERAL SAFETY Do not touch a pump while in operation as This is the safety alert symbol. When you see this symbol on they can operate at high temperatures. To avoid burns when your pump or in this manual, look for one of the following signal servicing the pump, shut off, allow it to cool for 30 minutes words and be alert to the potential for personal injury: after shutdown before handling.
- Page 5 SAFETY INFORMATION ELECTRICAL SAFETY OTHER DANGERS RISK OF FIRE OR EXPLOSION. cause severe personal injury, property damage or death. Hazardous voltage. Can shock, burn, Do not smoke or use open flames in or around this system. or kill. When installing, operating, or servicing this pump, Do not pump flammable liquids.
- Page 6 GENERAL INFORMATION If the lower seal leaks and moisture enters this chamber, the This manual contains important information for the safe use of moisture will settle to the bottom of the chamber and will this product. Read completely and do not throw away. complete (significantly less than 330K ohms) the circuit between Reasonable care and safe methods should be practiced.
- Page 7 GENERAL INFORMATION OVERLOAD HEATERS INSTALLING PUMP IN SUMP If the electrical panel is not used, starters with 3 leg overload relay must be supplied on 3 phase pumps. Each leg is to have an HAZARDOUS VOLTAGE. Can shock, burn, or kill. identical heater sized in accordance with the nameplate amps on When installing, operating, or servicing this pump, carefully the motor housing.
-
Page 8: Installation
INSTALLATION MAKING ELECTRICAL CONNECTIONS volt 3 phase cannot be rewired to any other voltage. TO RE-WIRE THE PUMP FROM 230V TO 460V 3 PHASE ElECTROCUTION HAZARD: Must be Only a 230V pump from the factory is considered dual voltage, a installed by a qualified professional. -
Page 9: Operation / Maintenance
OPERATIONS & MAINTENANCE PUMP MAINTENANCE RISK OF FIRE OR EXPLOSION. Do not smoke or use open flames in or around this system. Only the FM listed As the motors are oil filled, no lubrication or other maintenance is products are to be used in a hazardous location applications required. -
Page 10: Troubleshooting
TROUBLESHOOTING ADJUST CUTTER CLEARANCE ON CHOPPING MECHANISM Next back off the same 3/8-16 (Item C) screws away from CUTTING RISK. Risk of serious cutting liner plate 1/8 - 1/4 turn for the recommended .008-.015 or amputation exists. Use caution as liner plate is extremely clearance. - Page 11 TROUBLESHOOTING PUMP TROUBLESHOOTING PUMP DOES NOT DELIVER PROPER CAPACITY Discharge gate valve may be partially closed or partially Below is a list of common problems and the probable causes. clogged. PUMP WILL NOT START Check valve may be partially clogged. Raise level up and No power to the motor.
-
Page 12: Parts List
PARTS LIST HPS4SD(X), HPS4HD(X), HPS6MD(X) For use with product built with Premium Efficient motor. F4 F26 CONFIDENTIAL contains trade secrets and All drawings and specifications as well as processes, materials, CIRCLED DIMENSIONS ARE DESIGNED IN INCHES other proprietary information of Pentair compounds and other similar criteria are to be strictly adhered to. - Page 13 PARTS LIST ITEM PART DESCRIPTION PART # 4SD / 4HD / 6MD CORD CAP 10-4 35' 152880315 CORD CAP 8-4 35' 152880325 CORD CAP 6-4 35' 152880335 STATOR SEE MOTOR PARTS GROUP ROTOR/SHAFT ASSEMBLY SEE MOTOR PARTS GROUP SPACER SEE MOTOR PARTS GROUP 153620017 BOLT-STATOR 06106A027...
- Page 14 PARTS LIST HYDRAULIC ENDS PARTS LIST B7 F26 B11 F26 B3 F26 B11 F26 B3 F26 B11 F26 TYPICAL: GAP BETWEEN LINER(B15) AND IMPELLER(1) TO BE .008-.015" FROM FACTORY. ITEM DESCRIPTION PART # O-RING VOL COVER ** 05876A108 SCREW-HEX HEAD VOL COVER 002380301 SCREW-SOCKET HEAD CAP LINER BOLT 005560081...
- Page 15 PARTS LIST MOTOR PARTS LIST 25HP 25HP 30/40HP 30/40HP ITEM 2-POLE 3450 RPM 230/460/3/60 575/3/60 460/3/60 575/3/60 STATOR 27906D003 27906D603 27907D003 27907D603 ROTOR/SHAFT ASSEMBLY 27906D130 27906D130 27907D130 27907D130 153620017 (4 .8) 153620017 (4 .8) 153620017 (4 .25) 153620017 (4 .25) BOLT-STATOR 06106A027 (4)
- Page 16 PARTS LIST IMPELLER PARTS LIST - HPS4HD(X) 1750 RPM DESCRIPTION PART # VOLTAGE/PH CORD TRIM IMPELLER HPS4HDP025403 528650017 208/3 10 .75 154641142 HPS4HDP025423 528650027 230-460/3 10 .75 154641142 HPS4HDP025443 528650037 460/3 10 .75 154641142 HPS4HDP025453 528650047 575/3 10 .75 154641142 HPS4HDXP025403 528656017 208/3...
-
Page 17: Wiring Diagrams
WIRING DIAGRAMS E-03-601 (02-15-22) - Page 18 WIRING DIAGRAMS E-03-601 (02-15-22)
-
Page 19: Warranty
Pentair Hydromatic will cover only the lower seal and labor thereof for all dual seal pumps. under no circumstance will Pentair Hydromatic be responsible for the cost of field labor, travel expenses, rented equipment, removal/reinstallation costs or freight expenses to and from the factory or an authorized Pentair Hydromatic service facility. - Page 20 1101 Myers Parkway 490 Pinebush Road, Unit 4 pentair.com Ashland, OH 4805 Cambridge, Ontario, Canada N1t 0a5 Ph: 855.274.8947 Ph: 800.363.7867 Fx: 800.426.9446 Fx: 888.606.5484 All indicated Pentair trademarks and logos are property of Pentair . Third party registered and unregistered trademarks and logos are the property of their respective owners . Because we are continuously improving our products and services, Pentair reserves the right to change specifications without prior notice .