Related Manuals for Pentair Hydromatic S4T Series
Summary of Contents for Pentair Hydromatic S4T Series
- Page 1 HYDROMATIC SUBMERSIBLE SOLIDS HANDLING PUMP S4T(X) S8L(X) S8LA(X) S12L(X) (X) Models are used in Hazardous Locations Class I, Division 1 INSTALLATION AND OPERATION MANUAL pentair.com...
-
Page 2: Table Of Contents
TABLE OF CONTENTS: SECTION ........................................PAGE General Information ....................................3 Pump Installation, Operations & Maintenance ............................4 Pump Maintenance ....................................5 Troubleshooting ....................................... 6 Wiring Diagrams ....................................... 7 S4T, S8L, S8LA, S12L Motor End Components (Standard Location) ......................8 S4T, S8L, S8LA, S12L Motor End Parts List (Standard Location) ....................... 8 Impeller Parts List / Cord Cap (For Use With Product Built With Usem Motor) .................. -
Page 3: General Information
Overload Heaters: the owner of the equipment or to the responsible party who maintains If the Pentair Hydromatic* electrical panel is not used, start ers with 3 leg the system. overload relay must be supplied on three phase pumps. Each leg is to have This is the safety alert symbol. -
Page 4: Pump Installation, Operations & Maintenance
Disconnecting Pump Cords: If a Pentair Hydromatic hazardous location pump is to be removed from its In a triplex system, the third or override control is usually set 24" above the loca tion, the pump cords may be disconnected at control panel (on sump one pump turn-on control, and the fourth or second override control is mounted con trol panels) and cord as sem bly are taken with the pump. -
Page 5: Pump Maintenance
Hydromatic* service center. Charges will not be allowed if in warranty 1. Drain all oil from motor chamber and seal chamber as described. pump is not taken to an authorized Pentair Hydromatic service center. 2. Remove motor housing as described. -
Page 6: Troubleshooting
TROUBLESHOOTING The following is a list of common problems and their probable causes. Pump will not start. DUAL VOLTAGE 1. No power to the motor. Check for blown fuse or open circuit breaker. 3 PHASE MOTOR WIRING 2. Selector switch may be in the OFF position. 230V 3ø... -
Page 7: Wiring Diagrams
WIRING DIAGRAM E-03-503 (07/31/19) -
Page 8: S4T, S8L, S8La, S12L Motor End Components (Standard Location)
S4T, S8L, S8LA, S12L MOTOR END COMPONENTS (STANDARD LOCATION) VOLTAGE/ RING – BOX – ROTOR/ ph/RPM STATOR SPACER CONNECTION SHAFT 15–20 200/3/870 141632031 086620121 137690035 141630125 15–20 230/3/870 141630031 086620121 137690065 141630125 15–20 460/3/870 141630031 086620121 137690075 141630125 15–20 575/3/870 141636031 086620121 137690045... -
Page 9: Impeller Parts List / Cord Cap (For Use With Product Built With Usem Motor)
IMPELLER PARTS LIST / CORD CAP For use with product built with motors from U.S. Electrical Motors (USEM). Haz. Loc. Haz. Loc. Description Volt/ph Trim Impeller Cord Cap Description Volt/ph Trim Impeller Cord Cap Cord Cap Cord Cap S8LA(X) S4T(X) 1750 RPM 1750 RPM S8LA7500M4-4... -
Page 10: S4Tx, S8Lx, S8Lax, S12Lx Motor End Components (Hazardous Location)
S4TX, S8LX, S8LAX, S12LX MOTOR END COMPONENTS (HAZARDOUS LOCATION) WIRING DIAGRAMS PROBE TEST RESISTOR PROBE TEST RESISTOR ON HAZARDOUS LOCATION ONLY ON HAZARDOUS LOCATION ONLY – – PROBE TEST RESISTOR PROBE TEST RESISTOR PROBE TEST RESISTOR PROBE TEST RESISTOR PROBE TEST RESISTOR ON HAZARDOUS LOCATION ONLY ON HAZARDOUS LOCATION ONLY ON HAZARDOUS LOCATION ONLY... -
Page 11: S4Tx, S8Lx, S8Lax, S12Lx Motor End Parts List (Hazardous Location)
S4TX, S8LX, S8LAX, S12LX MOTOR END PARTS LIST (HAZARDOUS LOCATION) For use with product built with motors from U.S. Electrical Motors (USEM). Ref. Part Part Ref. Part Part Ref. Part Part Description Qty. Description Qty. Description Qty. 009750141 RING–RETAINING 107820013 RING–LABYRINTH 08565A026 BEARING–BALL (UPPER) -
Page 12: Standard Limited Warranty
(e) if the unit is moved from its original installation location; (f) if unit is used for purposes other than for what it is designed and manufactured; (g) to any unit that has been repaired or altered by anyone other than Pentair Hydromatic or an authorized Pentair Hydromatic service provider;...