Related Manuals for Pentair Hydromatic S4L(X)P
Summary of Contents for Pentair Hydromatic S4L(X)P
- Page 1 SUBMERSIBLE SOLIDS HANDLING PUMP C4H(X*)P H4Q(X*)P S4K(X*)P S4L(X*)P S4LV(X*)P S4B(X*)P S6L(X*)P S6A(X*)P S8F(X*)P (* Used in hazardous locations Class I, Division I, Groups C & D): FM INSTALLATION AND OPERATION MANUAL pentair.com...
-
Page 2: Table Of Contents
TABLE OF CONTENTS: SECTION ........................................PAGE Safety Information ....................................3 General Information ....................................4 Pump Installation ...................................... 5 Pump Operation & Maintenance ................................6 Troubleshooting ....................................... 7 Parts List ........................................8 Wiring Diagrams ......................................15 Warranty ........................................16... -
Page 3: Safety Information
SAFETY INFORMATION READ AND FOLLOW SAFETY INSTRUCTIONS! ELECTRICAL SAFETY ELECTROCUTION HAZARD: Must be installed by This is the safety alert symbol. When you see this symbol a qualified professional. First disconnect all electrical power on your pump or in this manual, look for one of the following before attempting service. -
Page 4: General Information
GENERAL INFORMATION the starter in the panel breaks power to the pump. This manual contains important information for the safe use of this product. Read completely and do not throw away. Once the sensor resets, the starter is automatically reset for FM for continued operation of the pump. -
Page 5: Pump Installation
PUMP INSTALLATION INSTALLING PUMP IN SUMP For record keeping purposes, we suggest the pump be marked Before installing the pump in the sump, lay it on its side and rotate externally with the new voltage and qualified personnel that impeller. Impeller may be slightly stuck due to factory test water. performed the change. -
Page 6: Pump Operation & Maintenance
Any pump that is in warranty must be returned to the factory for Double check all wire connections. service or repaired at an authorized Pentair Hydromatic service center. Charges will not be allowed if (in warranty) pump is not Turn pumps to Off position on H-O-A switches. -
Page 7: Troubleshooting
TROUBLESHOOTING Pump operates with selector switch in Hand position but will Pump Troubleshooting not operate in Auto position. Below is a list of common problems and the probable causes: This indicates trouble in the float level control or the Pump will not start. alternator relay. -
Page 8: Parts List
PUMP PARTS LIST C4H(X)P, H4Q(X)P, S4K(X)P, S4L(X)P, S4LV(X)P, S4B(X)P, S6L(X)P, S6A(X)P and S8F(X)P For use with product built with Premium Efficient motor. 3, 4 250 FRAME PUMPS 280 FRAME PUMPS Ref. Part No. Part Description Qty. Ref. Part No. Part Description Qty. - Page 9 HYDRAULIC ENDS PART LIST H4Q(X)P S4K(X)P S4L(X)P S4LV(X)P S4B(X)P S6L(X)P S6A(X)P S8F(X)P C4H(X)P D3, D6, D15 - Not shown in this view Item Description S4L(X)P S4B(X)P S4K(X)P S4LV(X)P H4Q(X)P S6L(X)P S6A(X)P S8F(X)P C4H(X)P IMPELLER 025940002 136920012 137200012 110430002 151510012 025940002...
- Page 10 MOTOR PARTS GROUP 250 FRAME PUMPS MOTOR PARTS GROUP 40 HP 40 HP 30 HP 30 HP 30 HP 20 – 25 HP 20 – 25 HP 20 – 25 HP 460/3/60 575/3/60 230/3/60 460/3/60 575/3/60 208-230/3/60 460/3/60 575/3/60 ITEM 4-POLE 1750 RPM STATOR 27904D003...
- Page 11 IMPELLER PARTS LIST 250 FRAME PUMPS IMPELLER PARTS LIST H4Q(X)P S4K(X)P CAT. NO. VOLT/PH CORD TRIM IMPELLER CAT. NO. VOLT/PH CORD TRIM IMPELLER 1750 RPM 1750 RPM H4Q(X)P2000DC 208/3 151510062 S4K(X)P2000DC 208/3 9.25 137200122 S4K(X)P2000EC 230/3 9.25 137200122 H4Q(X)P2000EC 230/3 151510062 S4K(X)P2000FC 460/3...
- Page 12 MOTOR PARTS GROUP 250 Frame Pumps Impeller Parts List S4L(X)P S6L(X)P CAT. NO. VOLT/PH CORD TRIM IMPELLER Cat. No. Volt/Ph Cord Trim Impeller 1750 RPM 1750 RPM S4L(X)P2000DC 208/3 9.88 025940372 S6L(X)P2000DC 208/3 9.88 025940372 S4L(X)P2000EC 230/3 9.88 025940372 S6L(X)P2000EC 230/3 9.88...
- Page 13 IMPELLER PARTS LIST 250 Frame Pumps Impeller Parts List S8F(X)P S6A(X)P Cat. No. Volt/Ph Cord Trim Impeller CAT. NO. VOLT/PH CORD TRIM IMPELLER 1750 RPM 1750 RPM S8F(X)P2000DC 208/3 9.63 025940302 S6A(X)P2500DC 208/3 136940132 S8F(X)P2000EC 230/3 9.63 025940302 S6A(X)P2500EC 230/3 136940132 S8F(X)P2000FC 460/3...
- Page 14 WIRING DIAGRAMS 280 FRAME PUMPS IMPELLER PARTS LIST S4L(X)P S4LV(X)P CAT. NO. VOLT/PH CORD TRIM IMPELLER CAT. NO. VOLT/PH CORD TRIM IMPELLER 1750 RPM 1750 RPM S4L(X)P5000FC 460/3 11.63 025940002 S4LV(X)P5000FC 460/3 110430002 S4L(X)P5000GC 575/3 11.63 025940002 S4LV(X)P5000GC 575/3 110430002...
-
Page 15: Wiring Diagrams
WIRING DIAGRAMS E-03-558 (07-05-20) -
Page 16: Warranty
Pentair Hydromatic authorized control panels are used. All seal fail and heat sensing devices must be hooked up, functional and monitored or this warranty will be void. Pentair Hydromatic will cover only the lower seal and labor thereof for all dual seal pumps.