Furuno SC-33 Operator's Manual
  1. Manuals
  2. Brands
  3. Furuno Manuals
  4. Marine GPS System
  5. SC-33
  6. Operator's manual

Furuno SC-33 Operator's Manual

Sc setting tool
Hide thumbs Also See for SC-33:
Table of Contents

Advertisement

Quick Links

OPERATOR'S MANUAL
SC Setting Tool
SC-33
SCX-20
SCX-21
Applicable model
www.furuno.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SC-33 and is the answer not in the manual?

Questions and answers

Related Manuals for Furuno SC-33

Summary of Contents for Furuno SC-33

  • Page 1 OPERATOR'S MANUAL SC Setting Tool SC-33 SCX-20 SCX-21 Applicable model www.furuno.com...
  • Page 3 • The operator of this equipment must read and follow the instructions in this manual. Wrong operation or maintenance can void the warranty or cause injury. • Do not copy any part of this manual without written permission from FURUNO. • If this manual is lost or worn, contact your dealer about replacement.

  • Page 4: Table Of Contents

    2.1 Display Layout....................... 9 2.2 [GNSS Setup] Tab ...................... 10 2.3 [Sensor Setup] Tab ..................... 11 2.4 [PGN Setup] Tab (SC-33/SCX-20 Only) ..............14 2.5 [Port Setup] Tab (SCX-21 Only).................. 15 2.6 [Simple Diagnostic] Tab ....................16 2.7 [Advanced Diagnostic] Tab (SCX-21 Only)..............18 2.8 [System Information] Tab (SCX-20/SCX-21 Only) ............

  • Page 5: Foreword

    (SCX-21). Use this software for the initial setting after the installation, setting adjust- ment, or performance check in the maintenance. This software is available for the SC-33. This software can be downloaded from the quick response code shown right.

  • Page 6: Operational Overview

    1.2.1 NMEA2000 network connection (SC-33/SCX-20) ™ You can connect the PC and SATELLITE COMPASS (SC-33/SCX-20) via the NMEA2000 net- ™ work. Prepare a CAN-USB converter to connect the PC to the SATELLITE COMPASS . When your CAN-USB converter is USBcan II or CANUSB, a drop cable is also required to connect the CAN-USB converter to the NMEA2000 backbone.
  • Page 7 1. OPERATIONAL OVERVIEW CAN-USB converter Prepare either one of the following converters: Manufacturer Model Kvaser Inc. USBcan II Kvaser Leaf Light HS v2 M12 LAWICEL AB CANUSB Note: A software driver is required to use the CAN-USB converter or NMEA2000 gateway. For detailed installation instructions, refer to the operator’s manual of the converter or the official web- site of the manufacturer.

  • Page 8: Nmea0183 Serial Connection (Scx-21)

    1. OPERATIONAL OVERVIEW 1.2.2 NMEA0183 serial connection (SCX-21) ™ You can connect the PC and SATELLITE COMPASS (SCX-21) via the NMEA0183 serial con- nection. Prepare a serial-USB converter (local supply), between the PC and the NMEA0183 port. For the serial-USB converter, use the HuMANDATA USB-003 Rev6. A software driver is required to use the HuMANDATA USB-003 Rev6.
  • Page 9 1. OPERATIONAL OVERVIEW 2. Click the [Next] button to continue. 3. Click the [Next] button to continue. 4. Click the [Next] button to start the software installation. The progress bar is shown while the SC setting tool is being installed. After completing the installation, the confirmation message appears.

  • Page 10: How To Start And Close The Sc Setting Tool

    How to Start and Close the SC Setting Tool ™ 1.4.1 How to connect a PC to the SATELLITE COMPASS 1. Make the connections shown below. NMEA2000 network connection (SC-33/SCX-20) SATELLITE COMPASS Power supply 12 VDC (Example drawing: SC-33) Converter...
  • Page 11 1. OPERATIONAL OVERVIEW 3. Activate the executable file of the SC setting tool (file name: "SC_Setting_Tool.exe") on your PC to show the [Select Device] dialog box. Note: When the following message appears the first time the SC setting tool is activated, install “Microsoft Vi- ®...
  • Page 12 [Connect] button. : Grayed out when the SCX-21 is connected. : Grayed out when the SC-33 or SCX-20 is connected. 4. Set the items referring to the table at step 3, then click the [Connect] button to connect the ™...

  • Page 13: How To Close The Sc Setting Tool

    1. OPERATIONAL OVERVIEW 1.4.2 How to close the SC setting tool ™ 1. If the settings are not applied to the SATELLITE COMPASS , click the [Apply] or [Apply All] button on the [SC_Setting_Tool] dialog box to apply the settings. 2.

  • Page 14: How To Setup The Menu

    HOW TO SETUP THE MENU Display Layout ™ Note: If connection between the PC and SATELLITE COMPASS is interrupted or stopped (PC battery, cable connection issues, etc.), some or all settings may not be applied to the SATELLITE ™ COMPASS .

  • Page 15: Gnss Setup] Tab

    2. HOW TO SETUP THE MENU Name Remarks [Apply] button Click this button to apply the settings on the currently displayed tab. The [Apply] and [Apply All] buttons are grayed out while applying the settings. [Apply All] button Click this button to apply the settings on all tabs. The [Apply] and [Ap- ply All] buttons are grayed out while applying the settings.

  • Page 16: Sensor Setup] Tab

    SBAS* mum of three satellites can be ignored. Note: A satellite number entered at [Satellite Selection] will be rejected. *: Grayed out when the SC-33 is connected. [Sensor Setup] Tab ™ Enter the ship’s information and mounting position of the SATELLITE COMPASS and adjust the sensor offset values from the [Sensor Setup] tab.
  • Page 17 2. HOW TO SETUP THE MENU Menu Item Remarks Setting range Dimensions/ Enter the appropriate value according to the ship’s size, to improve the accuracy CCRP of the 3-axis speed. The reference position for mounting position and calculating po- sition of the 3-axis speed are shown in the following figure: Reference position ( 0.0 )
  • Page 18 If the signal from the satellite can- not be retrieved within the time set here, ™ the SATELLITE COMPASS stops outputting the heading data. : Grayed out when the SC-33 is connected.

  • Page 19: Pgn Setup] Tab (Sc-33/Scx-20 Only)

    2. HOW TO SETUP THE MENU [PGN Setup] Tab (SC-33/SCX-20 Only) ™ You can enable/disable PGN output from the SATELLITE COMPASS and adjust transmission rate from the [PGN Setup] tab. Note: The [PGN Setup] tab is not used in the SCX-21. You can open the tab, however all setting items are grayed out and cannot be adjusted.

  • Page 20: Port Setup] Tab (Scx-21 Only)

    You can setup output data format for each serial channel (data port) on the SCX-21. Note: The [Port Setup] tab is not used in the SC-33 and SCX-20. You can open the tab, however all setting items are grayed out and cannot be adjusted.

  • Page 21: Simple Diagnostic] Tab

    2. HOW TO SETUP THE MENU Menu item Remarks Port1 Setup/ Sentence Click the [Open] button, and the [SentenceList] dialog box appears. All Port2 Setup/ Information ™ sentences that the connected SATELLITE COMPASS can output Port3 Setup are shown on the [SentenceList] dialog box. You can turn each sen- tence on or off and adjust the transmission rate.
  • Page 22 Common test results ROM/RAM ROM test result (OK or NG). Internal RAM Internal RAM test result (OK or NG). Test result for SC-33 TEST/RESULT GYRO Gyro sensor test result (OK or NG). From left: X-axis, Y-axis, Z- axis test result Acceleration sensor test result (OK or NG).

  • Page 23: Advanced Diagnostic] Tab (Scx-21 Only)

    You can perform the advanced diagnostic test from the [Advanced Diagnostic] tab. Note: The [Advanced Diagnostic] tab is not used in the SC-33 and SCX-20. You can open the tab, however all contents are grayed out and cannot be adjusted.

  • Page 24: System Information] Tab (Scx-20/Scx-21 Only)

    ™ The [System Information] tab shows the system information of the SATELLITE COMPASS Note: The [System Information] tab is not used in the SC-33. You can open the tab, however all contents are grayed out and cannot be adjusted. How to show the system information Click the [Get Information] button to show the system information.

  • Page 25: Restart/Reset] Tab

    2. HOW TO SETUP THE MENU [Restart/Reset] Tab ™ You can restart the SATELLITE COMPASS and restore factory default settings from the [Re- start/Reset] tab. Note: If the hdcom (Sp) sentence is turned on at the [SentenceList] dialog box (see section 2.5), ™...

  • Page 26: Sky Plot] Tab

    Select the antenna number for which to show the satellite information ([Antenna 1] to [Antenna 4]). Note: [Antenna 1] and [Antenna 2] are available for SC-33. However you can select [Antenna 3] and [Antenna 4] - the satellite information is not displayed.

  • Page 27: Debug Monitor] Tab (Scx-20/Scx-21 Only)

    You can export the received PGNs or sentence information, offline data and system log file from the [Debug Monitor] tab. Note 1: The [Debug Monitor] tab is not used in the SC-33. You can open the tab, however all con- tents are grayed out and cannot be adjusted.
  • Page 28 2. HOW TO SETUP THE MENU Item Remarks SCX-20 Record Export received PGNs and time information. Click the [Start] button. The file destination Received dialog box appears. Select the file location for the export file. After selecting the file lo- PGNs cation, recording process is started and the [Start] button is replaced with the [Stop] but- ton.

  • Page 29: Menu Tree

    127252 (Heave) (Off, 20, 25, 50, 100, 200, 1000, 2000 msec) 127257 (Attitude) (Off, 20, 25, 50, 100, 200, 1000, 2000 msec) 127258 (Magnetic Variation) (SC-33: Off, 100, 1000, 2000 msec; SCX-20: Off, 1000, 2000 msec) 129025 (Position, Rapid Update) (Off, 100, 200, 1000, 2000 msec)
  • Page 30 APPENDIX 1 MENU TREE 130316 (Temperature, Extended Range) (Off, 1000, 2000 msec) 130577 (Direction Data) (Off, 20, 25, 100, 200, 1000, 2000 msec) 130578 (Vessel Speed Components) (Off, 200, 250, 1000, 2000 msec) 130842 (Six Degrees of Freedom Movement) (Off, 20, 25, 50, 100, 200 msec) 130843 (Heel Angle, Roll Information) (Off, 20, 25, 50, 100, 200 msec) 130845 (Multi Sats in View Extended) (Off, 1000 msec) 130846 (Motion Sensor Status Extended) (Off, 1000 msec)
  • Page 31 APPENDIX 1 MENU TREE System Information Get Information (Shows system information.) Restart/Reset Restart Antenna Unit Restart (Restarts the SATELLITE COMPASS Reset Menu Settings Restart (Reset the user setting menu.) Factory Reset (Restore all factory default settings.) Sky Plot (Shows the available satellites and their elevation.) Debug Monitor SCX-20 Record Received PGNs (Exports received PGN information.)
  • Page 32 ・FURUNO Authorized Distributor/Dealer 9-52 Ashihara-cho, Nishinomiya, 662-8580, JAPAN A : MAY 2018 Printed in Japan All rights reserved. B : JAN . 20, 2020 Pub. No. OME-72851-B (REFU ) SC-33(SW) 0 0 0 1 9 4 9 6 6 1 1...

This manual is also suitable for:

Scx-20Scx-21Sc series

Table of Contents