Important Safety Instructions - Televes OSSGT Operating Instructions Manual

ELECTRIC-ARC FUSION SPLICER

Important safety instructions

General conditions for installation
1 . Read this manual before operating or connecting the
equipment.
2 . Keep these operating instructions in a safe place.
3 . Pay attention to all the warnings.
4 . Follow all instructions.
5 . Do not use this equipment near water.
6 . Clean the outside with a dry cloth only.
7 . Only use attachments/accessories specifi ed by the
manufacturer.
8 . Do not step on or pinch the network cable of the power supply
unit; pay special attention to plugs, power connections, and
the spots where they leave the equipment.
9 . Refer all servicing to qualifi ed service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped .
Warning
Equipment shall not be immersed in any kind of liquid. It is
recommended to avoid placing the device next too objects
fi lled with liquids, such as glasses.
Ambient temperature should not be higher than 50 °C .
Do not place the equipment near heat sources or in a highly
humid environment .
Do not place the equipment in a place where it can suff er
vibrations or shocks .
Please allow air circulation around the equipment .
Do not place naked fl ames, such as lighted candles on or near
the product.
How to charge the equipment safely
Power requirements for the power supply unit should be: 100-
240V~ 50/60Hz.
To disconnect the power supply from the mains pull the plug
never the cable.
It is strongly recommended not to connect the power supply
unit to the mains until all connections have been done.
Reduce the risk of fi re or electric shock, do not expose this
power supply unit to rain or moisture.
Fusion splicer precautions
1
The charging voltage of this fusion splicer is limited .
Always use the power supply unit provided with the equipment
to charge the internal battery .
2
Should the fusion splicer show any of the following anomalies
at some point:
- Weird smoke, smell or noise.
- Extreme heat.
- Weird liquid or matter inside the equipment.
- Breakdown or damage caused by falling o crashing.
You must switch off the equipment and immediately remove
the battery. Then, contact the Technical Support department
of Televés to proceed with its inspection or repair.
3
Internal manipulation of the fusion splicer involves losing the
product warranty (do not take the equipment apart).
4
Any errors in the equipment's external maintenance could
damage the fusion splicer or result in injury to the operator
(carefully follow the maintenance instructions).
5
Never use the fusion splicer in the presence of fl ammable
gases or liquids. Otherwise, it may lead to fi res, explosions or
other serious consequences.
6
This fusion splicer is only used for optical fi bre fusion, and
should not be used for any other purposes.
7
Do not expose the fusion splicer to high temperature or
humidity.
8
Avoid working in environments that are dusty or contain
airborne particles. This situation may cause failure in the fusion
operations or damage to the equipment.
9
Using the fusion splicer under diff erent climatic conditions
(going from a cold to a warm environment, for instance)
may generate condensation in the equipment. Wait for the
condensation to completely disappear before working with it.
10
To keep the appropriate performance of the fusion splicer
(based on the use that is made of it) we recommend cleaning
the equipment periodically.
11
The fusion splicer is calibrated infactory. Avoid strong
vibrations or impacts, and use its own case for transport and
storage.
12
Due to the high complexity of this equipment, it should only
be repaired by Televés.
Notes
Be aware that ignoring these warnings or using the fusion
splicer inappropriately may result in serious injuries: please
follow the recommended safety standards for this equipment.
Always use safety goggles when working with optical fi bre.
Symbology
The power supply unit is designed for indoor use.
The power supply unit meets the safety requirements
for class II equipment.
The equipmentcan not be treated as regular
house hold waste,and should be handed over to
the appropriate collection point for waste electrical
and electronics equipment (WEEE).
The equipment includes a recyclable battery;
prior to handing it over at the WEEE collection
premises, the battery should be removed from
the equipment and separately delivered for
appropriate management.
The equipment complies with the CE mark
requirements.
4