Haier Super Match Series Service Manual page 408

Operation
Base Operation
Remote controller
1. Unit start
Press ON/OFF on the remote controller, unit starts.
2.Select temp.setting
button
Press /
Every time the button is pressed, temp.setting
o
increase 1 C,if kept depressed, it will increase
rapidly
Every time the button is pressed, temp.setting
o
decrease 1 C,if kept depressed, it will
decrease rapidly
Select a desired temperature.
3.Fan function
Press button to enter additional options, when
cycle display to ,
enter to FAN function.
For each press button fan speed
changes as follows:
Remote controller:
MED
LOW
Air conditioner is running under displayed fan speed.
When FAN is set to AUTO, the air conditioner
automatically adjusts the fan speed according to room
temperature.
Remote
Operation
Controller
Mode
Under the mode of auto operation, air conditioner will
automatically select Cool or Heat operation according
AUTO to room temperature.
air conditioner automatically adjusts the fan speed
according to room
Cooling only unit do not have displays and functions
COOL
related with heating
In DRY mode, when room temperature becomes
DRY
lower than temp.setting+2
at LOW speed regardless of FAN setting.
In HEAT mode,warm air will blow out after a short
HEAT periodof the time due to cold-draft prevention function.
In FAN operation mode, the unit will not operate in
COOL or HEAT mode but only in FAN mode ,AUTO is
not available in FAN mode.And temp.setting is disabled.
FAN
When FAN is set to AUTO, the air conditioner automatically
adjusts the fan speed according to room temperature.
In FAN mode,SLEEP operation is not available.
1
Turbo/Quiet Auto
Cool Heat Dry
Temp+
2
Swing Swing
4
Temp-
2
3
Health Extra Function
Timer On
Sleep Confirm/Cancel
Timer Off
Reset
Lock
Light
will flash. And then press
Display
circulated
HI
Note
When FAN is set to AUTO, the
temperature.
o
C,unit will run intermittently
Emergency operation and test operation
Emergency Operation:
Use this operation only when the remote controller is defective
or lost, and with function of emergency running, air conditoner
can run automatically for a while.
When the emergency operation switch is pressed, the " Pi "
sound is heard once, which means the start of this operation.
When power switch is turning on for the first time and
emergency operation starts, the unit will run automatically in
the following modes:
Room Timer
Designated Fan
temperature mode
temperature speed
o o
Above 23 C 26 C AUTO
No
It is impossible to change the settings of temp. and fan speed,It
is also not possible to operate in timer or dry mode.
Test operation:
Test ope ration switch is the same as emergency switch.
Use this switch in the test operation when the room
o
C, do not use it in the
temperature is below 16
normal operation.
Continue to press the test operation
switch for more than 5 seconds . After
you hear the "Pi" sound twice, release
your finger from the switch: the cooling
operation starts with the air flow speed "Hi".
Under this operation mode,the fan motor of indoor
unit will run in high speed.
Air Flow Direction Adjustment
1.Status display of air flow
For each press of
displays as follows :
remote controller:
Pos.1
Initial state
Pos.2 No initial state disaplayed on remote controller, the
vertical flap will be fixed on the current position
2.Left and right air flow adjustment
For each press of
displays as follows :
remote controller:
Pos.1 Pos.3
Pos.2
Pos.6
Pos.5
Cautions:
When adjusting the flap by hand,turn off the unit.
When humidity is high,condensate water might occur
adjusted to left or at air outlet if all vertical louvers are right.
It is advisable not to keep horizontal flap at downward
position for a long time in COOLor DRY
otherwise, condensate water might occur.
Note:
When restart after remote turning off, the remote controller
controller will automatically memorize the previous set swing position.
407
System configuration
Pi
Operation
mode
COOL
Pi Pi
Vertical flap
button, remote controller
button, remote controller
Pos.4
mode ,
Domestic air conditioner