Specifications - Sonance Sonamp ASAP3D SE Instruction Manual

S A S A P 3 D S E S
®
O N A M P
AC T [AC Trigger] Pinhole Switch
RIG
The AC T pinhole switch (see Figure
RIG
21 ) lets the ASAP3D SE determine the
precise voltage appearing at its AC
T O that will trigger the
RIGGER UTLET
amplifier to switch from the House to
the Local source:
1. Place the TV that is connected to the
AC T O in the Standby or
RIGGER UTLET
OFF mode.
2. Push the AC T button.
RIG
• The H BBE LEDs on the ASAP3D SE's front panel
OUSE AND
will flash and the amplifier's microprocessor records the
[minimum] voltage level at the AC T
3. Turn the TV's power ON.
4. Push the AC T button again.
RIG
• The ASAP3D SE's microprocessor records the [maximum]
voltage level at the AC Trigger Outlet,
5. The ASAP3D SE calculates an AC trigger voltage that is
between the maximum and the minimum voltage levels that
will appear at the AC T
amplifier to switch sources when the TV turns ON.)
• When this process is completed the H
will stop flashing.
N : T A S A P 3 D S E
O T E H E
M O D E F O R A P P R O X I M AT E LY
O N . T
H I S P R E V E N T S A N Y A N N O Y I N G
F R O M B E I N G A M P L I F I E D T H R O U G H T H E S Y S T E M
To reset the AC Trigger Voltage to its factory level, unplug the
amplifier's AC cord and plug it back in while holding in the
AC T pinhole switch.
RIG
Status LEDs
The ASAP3D SE front
panel has three LEDs (see
Figure 22 ) that provide
the amplifier's normal
operating status:
H : Illuminates when
O U S E
the House source is active.
L : Illuminates when the Local source is active.
OCAL
BBE: Illuminates when BBE Sound Enhancement is active.
The H LED also flashes to indicate various protection and
OUSE
operational error conditions (see table in Appendix 3 , on
page 14).
P A
T E R E O O W E R M P L I F I E R
F
IGURE
AC T
[AC T
RIG
O
RIGGER UTLET
O . (This allows the
RIGGER UTLET
OUSE AND
H
W I L L S TAY I N T H E O U S E
2 T V
S E C O N D S A F T E R T H E
T V
S W I T C H I N G N O I S E S
'
S S P E A K E R S
F 22:
IGURE
F -P S
RONT ANEL TATUS
BBE Sound Enhancement
The Sonamp ASAP3D SE incorporates
BBE ® Sound Enhancement. The BBE
process improves music's presence and
detail, especially at lower listening vol-
umes. This improves the sound of your
audio system, particularly distributed
21:
audio systems playing background
RIGGER
music. BBE also restores clarity and
] B
UTTON
definition (or focus) to spoken voices,
which makes paging systems easier to
understand without having to run them at high volumes.
The ASAP3D SE has 2 individual switches to set the BBE
enhancement (see Figure 23 ):
.
• If the BBE ON/OFF switch is set to OFF, BBE enhancement
is not applied.
• If the BBE ON/OFF switch is set to ON, BBE enhancement
is applied
LO/HI switch: LO = +3dB of BBE enhancement; HI = +6dB
of BBE enhancement.

Specifications

Number of Channels:
BBE LEDs
Output Power (Stereo):
S O U R C E
S W I T C H E S
.
Frequency Response:
Total Harmonic Distortion: 0.10% (1kHz, 8 ohms);
Signal to Noise Ratio:
Input Sensitivity:
Input Impedance:
Maximum Source Input: 2.3VAC RMS
LED
S
Voltage
Power Consumption:
Heat Output:
AC Fuse:
Dimensions (W x H x D):
Rack Space Requirements: 1U (½-rack width)
Weight:
according to the
2 (one stereo pair)
25 watts RMS per channel, 0.25% THD,
20Hz – 20kHz, @ 8 ohms
50 watts per channel, 0.25% THD,
1kHz, @ 4 ohms
20Hz – 20kHz +1/-3dB
0.25% (1kHz, 4 ohms)
-94dB (w/22kHz A-WTG filter);
-88dB (with AC-sensing trigger)
0.9V for 25W RMS output
0.7V w/BBE ON (+3dB)
0.5V w/BBE ON (+6dB)
13k ohms
1.3VAC RMS w/BBE ON
250 Watts maximum (4 ohms, full power)
17 Watts idle (no signal)
28 BTU/HR @ 8 ohms (rock music)
55 BUT/HR @ 4 ohms (rock music)
1.25A (T1.25AL ~ 250V)
9½" x 1¾" x 12½"
(241mm x 45mm x 318mm)
7 lbs (3.2kg)
F 23:
IGURE
BBE M DIP
ODE
S
WITCHES
setting of the
9