Table of Contents
Advertisement
S
A S A P 1 D S
®
O N A M P
T E R E O
Front Panel Indicators and Controls
Volume Controls
The
front-panel
V
O L U M E
C
potentiometers (see
ONTROL
Figure 9 ) control the volume
of the Local source. These can
be
used
to
balance
volume of the Local source
against the volume of the
House source (the volume of
which is determined by the
source component feeding the house source speaker input
connections). Use a small screwdriver or similar tool to adjust
the potentiometers.
Trigger Sensitivity Adjustment
The amount of Local-source audio
input voltage required to switch the
ASAP1D from the House source to the
Local source can be adjusted with the
front-panel T
S
RIGGER
ENSITIVITY
tiometer (see Figure 10 ). Turning the
control
clockwise
increases
trigger sensitivity — requiring less
signal to trigger the input change.
The full clockwise position is 1mV;
the full counter-clockwise position is OFF.
Switching Delay Time Adjustment
The amount of time it takes for the
ASAP1D to revert back to the House
source after the L
OCAL
signal has ceased can be adjusted with
the front-panel B
A D
TO
potentiometer (see Figure 11 ). Turning
the control clockwise decreases the
delay time.
The minimum delay time is 3 seconds;
the maximum is 2 minutes.
N
: S
O T E
E T T H E D E L AY T O A S O M E W H AT L O N G E R T I M E I F T H E
V
T
I D E O
R I G G E R I S N O T B E I N G U S E D
O F T E N P L AY S C L A S S I C A L M U S I C O R O T H E R P R O G R A M M AT E R I A L
,
W I T H L O N G
Q U I E T PA S S A G E S
6
P
A
O W E R
M P L I F I E R
L
the
VOLUME CONTROL
F
9:
IGURE
V
C
OLUME
ONTROLS
TRIGGER
poten-
SENSITIVITY
F
IGURE
the
T
RIGGER
S
ENSITIVITY
A
DJUSTMENT
input audio
B TO A
A
ELAY
DJUST
DELAY ADJUST
F
IGURE
S
WITCHING
D
A
ELAY
DJUSTMENT
,
O R I F T H E L O C A L S O U R C E
.
Active Input Indicators
The ASAP1D front panel has two LEDs
(see Figure 12 ) that indicate which
input is active:
A: Illuminates Red when the House
source is active.
B: Illuminates Green when the Local
R
source is active.
Specifications
Number of Channels:
Power Output
(both channels driven): 35 watts per channel @ 4 ohms
Frequency Response:
Total Harmonic Distortion: 0.10% (1kHz, 8 ohms)
Signal to Noise Ratio:
Input Sensitivity:
10:
Input Impedance:
Power Consumption:
Heat Output:
AC Fuse (120V ver):
AC Fuse (230V ver):
Dimensions (W x H x D): 12
Shipping Weight:
11:
A
F
IGURE
A
CTIVE
I
NDICATORS
2 (one stereo pair)
25 watts per channel @ 8 ohms
20Hz – 20kHz +1/–3dB (hi-pass filter OFF);
–3dB @ 27Hz (hi-pass filter ON)
0.25% (1kHz, 4 ohms)
95dB (w/22kHz A-WTG filter)
485mV for 25W RMS output
47kohms
140 watts maximum (4 ohms, full power)
18 watts idle (no signal)
43 BTU/hour @ 8 ohms (rock music)
60 BTU/hour @ 4 ohms (rock music)
2A (T2AL ~ 250V)
1A (T1AL ~ 250V)
5
5
⁄
" x 3" x 4
"
/
8
8
(321mm x 77mm x 118mm)
7 lbs. (3.2kg)
B
12:
I
NPUT
Advertisement
Table of Contents
