ORiNG TGS-1080-M12 Series Quick Installation Manual

EN50155
Switch
Q I
I N D U S T R I A L
uick nstallation
Introduction
The TGS-1080-M12 and TGS-1080-M12-BP2
are designed for industrial applications, such as rolling stock, vehicle, and
railway applications. The switches boast EN50155 compliance and M12
connectors to ensure tight and robust connections, and guarantee reliable
operation against environmental disturbances, such as vibration and shock.
Both models feature eight 10/100/1000Base-T(X) ports, but the
M12-BP2 model also provides two sets of bypass ports that ensure constant
network connectivity during power failure. Even if the switch loses power,
traffic will continue to flow unimpeded through the link. Besides standard
voltage range (12~48VDC), models with mediume voltage range
(72~110VDC) are also avaialble.
Package Contents
The devices are shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative for
assistance.
Contents Pictures
TGS-1080-M12 or
TGS-1080-M12-MV or
TGS-1080-M12-BP2 or
TGS-1080-M12- BP2- MV
QIG
Preparation
Before you begin installing the device, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Safety & Warnings
Elevated Operating Ambient: If installed in a closed environment, make sure
the operating ambient temperature is compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Reduced Air Flow: Make sure the amount of air flow required for safe operation
of the equipment is not compromised during installation.
Mechanical Loading: Make sure the mounting of the equipment is not in a
hazardous condition due to uneven mechanical loading.
Circuit Overloading: Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing
this concern.
Q I G
TGS-1080-M12 Series
TGS-1080-M12 Series
G
uide
Dimension
unmanaged Ethernet switches
TGS-1080-
15.0
65.0 21.3
TGS-1080-M12(-MV)
Panel Layouts
Number
Front View
1
TGS-1080-M12
PWR PWR1 PWR2
1
2
3
4
1 1 BI_DC+
2 BI_DD+ 1 2
3 BI_DD-
5 4 BI_DA- 7
5 BI_DB+
6 BI_DA+ 6 4
7 BI_DC-
5 8
8 BI_DB-
V1+
V1-
6
Power
Installation
Wall-mount
The device can be fixed to the wall. Follow the steps below to install the device on the wall.
Step 1: Hold the
Step 2: Insert four screws through the large opening of the keyhole-shaped apertures at the
top and bottom of the unit and fasten the screw to the wall with a screwdriver.
Step 3: Slide the
1907-2-29-TGS1080M12-1.1
125.0
86.0
56.5
R2.5
15.0
R4.00
Relay N.C. Relay Output
3A@24VDC
TGS-1080-M12 TGS-1080-M12-BP2
PWR PWR1 PWR2 Fault PWR PWR1 PWR2
LNK/ACT
DPX/COL
1 BI_DC+ 1 BI_DC+
2 BI_DD+ 1 2 G4 G8 2 BI_DD+ 1
4 BI_DA- 3 BI_DD- 7 3 4 BI_DA- 3 BI_DD- 7
5 BI_DB+ 5 BI_DB+
6 BI_DA+ 6 4 6 BI_DA+ 6
7 BI_DC- 5 8 7 BI_DC- 5
8 BI_DB- LNK/ACT 8 BI_DB-
DPX/COL
G3 G7
V1+ V2+ LNK/ACT V1+
DPX/COL
V1- V2- V1-
G2 G6
LNK/ACT
DPX/COL
G1 G5
Power Power
65.0 21.3
TGS-1080-M12-BP2(-MV)
1. Power status LED
Relay
N.C. Relay Output
3A@24VDC 2. Power1 status LED
7
(TGS-1080-M12 and TGS-1080-M12-BP2 only)
Fault
3. Power2 status LED
LNK/ACT
8
DPX/COL
(TGS-1080-M12 and TGS-1080-M12-BP2 only)
G4 G8
3 4. Fault LED
LNK/ACT
(TGS-1080-M12 and TGS-1080-M12-BP2 only)
DPX/COL
5. M12 pin definition
G3 G7
9
6. Power port
V2+
LNK/ACT
7. Relay output port
V2- DPX/COL
10
G2 G6
8. Gigabit Ethernet ports (G5-G8 of
TGS-1080-M12-BP2 as bypass ports)
LNK/ACT
DPX/COL
9. LAN port LNK/ACT LED
G1 G5
10. LAN port Duplex/Collision LED
d evice upright against the wall
d evice downwards and tighten the four screws for added stability.
Instead of screwing the screws in all the way, it is advised to
leave a space of about 2mm to allow room for sliding the switch
between the wall and the screws.
PRINTED ON RECYCLED PAPER
EN50155 8-port unmanaged

Ethernet switch

Wiring
For pin assignments of power, console and relay output ports, please refer to the following tables.
Grounding
Grounding and wire routing help limit the effects of noise due to electromagnetic interference
(EMI). Run the ground connection from the grounding pin on the power connector to the grounding
surface prior to connecting devices.
125.0
86.0
56.5
R2.5
Power port pinouts
R4.00
The device supports two sets of power supplies and uses the M23 5-pin
Relay N.C. Relay Output
3A@24VDC
female connector on the front panel for the dual power inputs.
Fault
LNK/ACT
Step 1: Insert a power cable to the power connector on the device.
DPX/COL
2 G4 G8
3
Step 2: Rotate the outer ring of the cable connector until a snug fit is
4
8
LNK/ACT
DPX/COL
Power
G3 G7 Failure achieved. Make sure the connection is tight.
Bypass
V2+ LNK/ACT
DPX/COL
V2-
G2 G6
LNK/ACT
Relay output port pinouts
DPX/COL
G1 G5
The switch uses the M12 A-coded 5-pin male connector on
the front panel for relay output. Use a power cord with an
M12 A-coded 5-pin female connector to connect the relay.
The relay contacts will detect user-configured events and
form an open circuit when an event is triggered.
Gigabit Ethernet port pinouts
TGS-1080-M12-BP2 has 8 gigabit Ethernet ports
sets of bypass ports that protect the network from
failures by ensuring network integrity during power loss.
Network Connection
The switch has eight 10/100/1000Base-T(X) Ethernet ports in the form of M12 connector.
Depending on the link type, the switch uses CAT 3, 4, 5,5e UTP cables to connect to network
devices (Pcs, servers, switches, routers, or hubs). Please refer to the following table for cable
specifications.
Cable Type Max. Length
10BASE-T Cat. 3, 4, 5 100-ohm UTP 100 m (328 ft)
100BASE-TX Cat. 5 100-ohm UTP UTP 100 m (328 ft)
Cat. 5/Cat. 5e 100-ohm
1000BASE-T UTP 100 m (328ft)
UTP
M12/8P Pin Definition
For pin assignments of the LAN ports, please refer to the following tables.
1 2
10/100/1000Base-T(X) M12 ports
7 3
Pin No. Description
6 4
#1 BI_DC+
5 8
#2 BI_DD+
#3 BI_DD-
#4 BI_DA-
#5 BI_DB+
#6 BI_DA+
#7 BI_DC-
#8 BI_DB-
Version 1.1
V1+ V2+
V1- V2-
Relay
N.C.
3A@24VDC
includes 2
1 2
7 3
6 4
5
8
Connector
8-pin female M12
A-coding connector
8-pin female M12
A-coding connector
8-pin female M12
A-coding connector
Quick Installation Guide